I watched and looked up a bunch of things trying to get my flashers working. With watching yours I started quick pushing my hazard button and bam, they worked. Ended up the hazard button was stuck. Can't thank you enough.
Thank you so much for this video David, I fixed my truck lights in 5 minutes thanks to your video, I didn’t know that specific relay is blue, someone had a regular grey relay in it, that is why it wasn’t working 👍🙏
Put the cover back on, the relay can vibrate loose if you don’t, especially if you have a Diesel engine. They need three relays, right side , left side , and hazards. That’s the way they are in road tractors and dump trucks.
I replaced the turn signal/multi-function switch, figuring the switch contacts had worn. I didn't notice that my hazard lights were working intermittently like my turn signals until after I had replaced the turn signal switch, and then proceeded to test all my functions. Since mine works intermittently, I'm wondering if the flasher unit relay is loose and making intermittent contact? I've decided to just buy a new flasher unit relay and make sure it's secure. Maybe I'll carry the old one for a back-up with my spare fuses if it is still good!?
I have no power going into the flasher (1995 e350 RV) I am trying to sell this damn thing and now the flashers dont work... of course it couldnt just be a bulb or the flasher unit. I am being told I need to trace the wires back and there is likely a problem with the ground or wiring... I dont see how I will be able to accomplish this. Not sure if replacing the switch is worth doing at this point, but I sure could use some advice.. thanks.
Play with the switch Push it in slow some will start working just before the click If it starts working it’s the switch If you have no power still to the flasher. Then it’s not a ground Ck the fuse if blown u have ether a short to ground. If it takes a while to blow u have high resistance. Sometimes I can just throw leds replacements and that will help
Interesting that the hazards and blinkers use the same relay because my Volkswagen Golf uses one relay for both the hazards and blinkers also. The Volkswagen one was much easier to change out.
I didn't find what you was talking about. Mine is a 97 f250 HD 7.3. But while I was looking for it I found another flashing relay that connects to the back of the fuse panel. Swapped it out and everything works. Iv never seen fuse panels with fuses on both sides. Hope this helps someone.
Sounds like this part needs to be replaced A-Premium Turn Signal Switch, Windshield Wiper Washer, Hazard Warning Flasher, Multifunction Switch, Compatible with Ford F-150 1999-2003, F-250/350/450/550 Super Duty, Blackwood, YL3Z13K359ABA a.co/d/1YNy38E
It does operate that as well but it is on a different circuit The blinkers and hazard is tied in together Brakes not as much but on some years it’s possible Ck for voltage at the brake light switch. If you have voltage I would say test the switch for continuity when the switch is pressed in. If the switch is fine and you have voltage Check the ground to make sure it’s ok Or run a new ground press the brake pedal see if lights work
thx, This is what the problem was. Still works i unplugged it plugged it back in worked good for a little while Doordashing went out one point and came right back on. Thinks its the connection. going to spray wd40 in it later
Quick question when you press the hazard button it's just 2 setting correct..1push for hazards on and 1 push for hazards off. (Have an issue where it is 4 settings with 1 of the settings being no turn signals 10 e350 bus)
change the relay they are cheap at autozone you can get 4 there for ONE Ford OE and they are the same. If that don't work then you have to get into the steering column and take out the cluster switch and replace it. Make sure the fuse is good as well (check it first) then flasher then cluster switch. Cheap to expensive. Easy to harder
Hey hoping you can help I have a 2004 Cadillac deville I purchased it like this no hazards ,blinkers or dash indicators I am hearing clicking every time I use blinkers or hazards but nothing happens what do you think ?
Just going to run down some stuff even if you probably check it already Start with the fuse at the fuse blocks Check engine compartment and inside cab, look for blinkers and the hazard Then check the relays for blinkers and the hazard make sure you have power going In and out of fuses and relays. The if all good you will need to check the blinker unit just because you hear it clicking doesn’t mean it works, they are electronic and that clocking is fake you need to make sure u have the pulse of electric going out . If all good then you need to start checking the steering column the hazard button and the switch arm for the blinkers make sure they are not worn out Good luck
@@DavidsHowtosReviews checked fuses and fuse box with light tester I haven’t replaced the turn signal flasher I’m hoping it’s that but if not I’ll look at my steering column like you said thanks for the response
So when I turn my hazards on only the green arrow indicating the right side shows up. Neither of my blinkers are working either. Would it be the same issue? I hear the clicking when using my hazards.
Check the ac fuse inside the cab Fuse 24. 10amp That’s for the clutch Under hood is #36 it is a diode that’s for ac clutch also Check the ac pressure, if the pressure is to low it will shutdown the system
My hazards work, but the blinkers don't. They usually won't work when it's cold or they take a while to work after the truck is warm. Is that the same issue?
@benl4707 the hazard/blinker switch unit needs to be replaced It on Amazon It can also be the flasher unit that unit works by heat This is what it will look like Depends on your yr ,make ,model EP27 Fits for Ford F150 (97-12), F250-F450 (99-10) Super Duty Trucks EP27 Flasher Realy, Fix Hyper Flash, Compatible LED/Stock Bulb Electronic Turn Signal and Hazard Warnning, Flasher Relay a.co/d/b2hGrKW
SOLVED! I've read many threads just like this and you guys mostly have my exact problem. Here's what the problem was and how I fixed it: First, in my 2012 Ford F150 the right blinker (flasher)/ brake light would not work. Turn signal blinked fast inside and for the front light and the mirror signal but tail light blinker would not flash. The bulbs were fine, I even replaced with new just to double down. The tail lights would light up when my headlights were on (running lights) but would not get brighter when brake depressed and would not flash for turn signal. I will tell some of you to keep in mind that yours may light up also so you don't think you have a bulb out but keep in mind there are two sepperate tungstan filaments (squiggly light wires) in each tail light and the brakes and flasher one could be bad and your running tail lights still work so definately change your bulbs FIRST, then do this if that was not it. So I had the problem for many months and refused to take my truck to the dealer where of course they will want to replace things and rewire and god knows what else and I've read where one guy says Ford charged him like $800 to fix this. I fixed this problem with $9.00. Saw a RUclips video with a guy with the same problem and he bought an ELM Interface scanner, plugged into the vehicle under the steering wheel and scanned his own truck with an Android app. So I bought the same one on Amazon (here is the link) www.amazon.com/gp/product/B081WYWZ6B/ref=ppx_yo_dt_b_asin_title_o09_s00?ie=UTF8&psc=1 I found a free app called Car Scanner ELM OBD2 by OvZ it's a generic looking logo of a blue square with a white engine. But I actually saw tons of these apps and I'm sure other apps would work fine as long as they're ELM OBD2 scanning apps with high ratings. I scanned my truck hoping to see some code come up about the BCM (body control module which is where the problem is) but did not see that code. Didnt matter. I CLEARED what unuseful codes I did see and that immediately fixed the problem and my damn flasher and brake lights are all working again. THANK GOD FOR THIS. Super cheap and easy. I'll never go to a dealership. Hope this helps y'all.
Lucia Aguirre No I would check the rear light wires and or the trailer socket and wires if your trailer harness uses same fuse, some of the truck have separate fuses for the trailer electric
Lucia Aguirre That’s a short to ground So the short is from the steering column where the lever is to fuse box Did anyone work on the inside of the truck in the steering column? Or even under the dash by the pedals? The blinker switch assembly may need to be looked at or even the fuse block Those are Notorious for water leaking on the fuse block and making truck do wacky things Even drain the battery for no reason Or radio to do wacky things
David Behr's Phantom Industries thank you I changed the single switch and it stop doing it. Had a lot of shortages but now all good. Thank you so much for your help.
I have a 2004 F350 and when I use my right or left turn signals my tail lights flash as if I have my hazard lights on could this be because of a bad relay shown in this video?
That sounds more like a ground wire in the back of truck Check and clean the tail light grounds Electric finds ground even if it’s going through another bulb to get to it. Or it’s possible the wires are crossed. If there was work done on truck I would check to see if something was done to cause this.
Hazards work and turn signals work but I have no clicking sound, (I also have no chime sound when turning the car on) could my problem be related to this part? 2008 Ford Explorer
I need some help with my 2018 Ford F-150 , Oem Led headlights and the left front blinker stopped working. All others till work. I am at a lost. I am Firefighter not a mechanic, Help ?????
So... my hazards went out the other day and I noticed that the blinkers also went at the same time. Now I’ve realized that my brake lights are out also. I’m guessing they all went out together. I checked the fuse and it’s fine. After looking at this video I’m guessing this is my next step. Do you agree? And just as a side note... who puts brake lights and blinkers and hazards all on the same unit? Seems like a safety hazard to me 🤷♀️
Yes try this for fist If this fixes only the blinkers then try the brake switch which is on the brake pedal I have a video on that as well. If it fixes everything then you’re all set. And yes Ford does some strange things that is unsafe in my opinion Everything should be separated especially the hazards
What happens if I'm getting power to the relay but no power to the flasher fuse. And the relay isn't clicking and I have no indication lights only dash either
That sounds like ur flasher lever is shot Check for voltage into the lever and out If you have voltage in but not out time to replace lever If u have no voltage in then u need to check for cut wires Also check the fuse block for sign of water the windshield on these tend to leak onto the fuse block
what could cause my running lights to stay on rather the switch is on or off the only way to turn them off to disconnect the batteries ? if you know the answer it would be appreciated!
@@DavidsHowtosReviews alrighty so I ordered a new headlight switch and installed it but it didn’t work do you have any other ideas when I turn it on they come on really bright but when everything‘s off they’re still on but you can tell it it’s not at the full power
Before you go crazy Check the relay make sure it’s not stuck on just swap relays with another that in in the fuse block. Also check the fuse block under dash, if the windshield leaks it goes right onto the fuse box look for signs of water that has leaked down or whet the roof where the lights are and windshield You are looking for bad relay first Water in fuse block second Last chase the wires for those lights see where it is getting the power. Good luck If that’s not to problem you will have to start chasing wires because
@@leviprine9490 I would start with the socket where the bulb is, as long as u roiled out the bulb itself. If the socket is good not corroded or melted, Then follow the wires. Also, dose the blinker work or only the back light? Check for voltage at plug. If you have voltage then check the ground. Good luck
I replaced the socket by borrowing the left one, the back right blinker works, its just the front right not working, the more i think about it the more i think its an isolated thing. I think its some kinda problem between the signal switch on the steering column and the harness for the blinker bulb(I replaced the blinker bulb , theres a crack in the plastic light cover, its a second hand truck I'm trying to maintainence up)
@@leviprine9490 did you find a solution my truck is doing the same thing but only my front right one is working my back right don’t work an I replaced the bulb so would a fuse still do that? Or is it something bigger
What is the issue, No blinkers, but hazard, no hazard, but blinkers. I would definitely check for voltage at both sides of fuse, then ck for voltage at the flasher unit then ck the switch up on top of steering column. The switch on top of the steering column tends to go bad.
I would first check for voltage before and after hazard button, the button tends to wear out but works like it should just dose not let voltage through If you have cked this already please let me know what u did thus far.
Change this A-Premium Turn Signal Switch, Windshield Wiper Washer, Hazard Warning Flasher, Multifunction Switch, Compatible with Ford F-150 1999-2003, F-250/350/450/550 Super Duty, Blackwood, YL3Z13K359ABA a.co/d/4KGTSQY
If you have over 100k more then likely it’s the blinker switch on the column. Also the hazard switch usually where is Al and you need to wiggle the switch for the hazards sometimes it will get everything to work again, but if it does replace the hazard switch.
Also make sure you check the common things like fuses and grounds just in case a wire got pinched by the frame or something like that and popped the fuse.
Unfortunately I did everything that you said in the video and it did go by an oem which was $46 but it turns out that this is not the problem my turn signal still doesn't work but my emergency flashers work's just trying to figure out which are the relays for the Flasher or the fuses is that something you can help me with?
I would start with the directional lever on steering column one viewer said their’s needed to be replaced. Check for voltage in and out of that. Check for voltage before replacing parts voltage in, voltage out. Just make sure all fuses are good Not that the flasher relay got hot and popped the fuse.
That really sounds like the signal lever needs to be replaced This is the part just make sure to check your application shop.advanceautoparts.com/p/motorcraft-original-equipment-o.e.-switch-assembly-direction-indicator-sw-6524/11865635-P
If you have power at fuse I would say the flasher switch/ arm needs replacement. If there is no voltage at fuse then there is a problem with ether the fuse block, follow the voltage.
I have that problem. Nothing happens when flashers on, except my brake lights don't work. Turn flasher off, brake lights work. No blinker lights or noise. Weird.
i was diagnosing my dads truck signals last night. they werent going, and neither were 2 of the 3 brake lights. weird right? the one on the back of the roof was still ok. meanwhile that freaky buzzy noise you demonstrate was happening cause i left the 4-ways "on" while i was upside down in the footwell. pressed n massaged the 4-way button and for some reason signals n brakes came back. im making him replace this blasted fuse tomorrow. 😎
You may have a BCM issue which you can fix for $9 with a scanner and a free app. See my other comment here on this video comment thread for full explanation
If they stay solid and dont blink but inside your signal is blinking fast its probably your BCM. Scan it and clear the code yourself with a cheap scanner. Easy cheap fix
@@DavidsHowtosReviews like my hazards and turn signal lights will be working on the outside of the vehicle, but I don’t see them working on the inside on the dash. Could it be the thermal flasher right?
That sounds like you have something going on with the wire leading to dash or the lights inside the dash for the indicators are burnt out Ck for voltage at input for the dash
I would think this blinker hazard unit is bad as long as you made sure there are no wires cut or crossed www.1aauto.com/ford-turn-signal-combination-lever-trq-swa41775/i/1azcc00017
![[SFM] Risky Recital](http://i.ytimg.com/vi/RzNkY1_Nk3o/mqdefault.jpg)
I watched and looked up a bunch of things trying to get my flashers working. With watching yours I started quick pushing my hazard button and bam, they worked. Ended up the hazard button was stuck. Can't thank you enough.
This is a good video, quick and succinct, really appreciate how streamline it was
Good video, other super "experienced" mechanics were saying to tear out the entire stereo to get to this relay. Thanks for the tip.
Thank you so much for this video David, I fixed my truck lights in 5 minutes thanks to your video, I didn’t know that specific relay is blue, someone had a regular grey relay in it, that is why it wasn’t working 👍🙏
Put the cover back on, the relay can vibrate loose if you don’t, especially if you have a Diesel engine. They need three relays, right side , left side , and hazards. That’s the way they are in road tractors and dump trucks.
Thank you, found the relay, gave it a smack with a big sharpie, and it started working again. At least long enough to get me legally to the dealership
Awesome glad it worked for u!
Stay safe..
Dude!!! You are the man !!! Thank you soooo much!!! Qas driving me crazy!!!
Thanks! Got me back on the road!
I replaced the turn signal/multi-function switch, figuring the switch contacts had worn. I didn't notice that my hazard lights were working intermittently like my turn signals until after I had replaced the turn signal switch, and then proceeded to test all my functions. Since mine works intermittently, I'm wondering if the flasher unit relay is loose and making intermittent contact? I've decided to just buy a new flasher unit relay and make sure it's secure. Maybe I'll carry the old one for a back-up with my spare fuses if it is still good!?
I have no power going into the flasher (1995 e350 RV) I am trying to sell this damn thing and now the flashers dont work... of course it couldnt just be a bulb or the flasher unit. I am being told I need to trace the wires back and there is likely a problem with the ground or wiring... I dont see how I will be able to accomplish this. Not sure if replacing the switch is worth doing at this point, but I sure could use some advice.. thanks.
Play with the switch
Push it in slow some will start working just before the click
If it starts working it’s the switch
If you have no power still to the flasher.
Then it’s not a ground
Ck the fuse if blown u have ether a short to ground.
If it takes a while to blow u have high resistance.
Sometimes I can just throw leds replacements and that will help
Thank you, just noticed my hazards and turn signals stopped working this morning.
Interesting that the hazards and blinkers use the same relay because my Volkswagen Golf uses one relay for both the hazards and blinkers also. The Volkswagen one was much easier to change out.
Yea they are all different
I didn't find what you was talking about. Mine is a 97 f250 HD 7.3. But while I was looking for it I found another flashing relay that connects to the back of the fuse panel. Swapped it out and everything works. Iv never seen fuse panels with fuses on both sides. Hope this helps someone.
Very helpful 👌
Would this issue effect brake lights aswell? Turn signals, hazard button and brake lights all went out at same time for me
Sounds like this part needs to be replaced
A-Premium Turn Signal Switch, Windshield Wiper Washer, Hazard Warning Flasher, Multifunction Switch, Compatible with Ford F-150 1999-2003, F-250/350/450/550 Super Duty, Blackwood, YL3Z13K359ABA a.co/d/1YNy38E
@DavidsHowtosReviews That's what I was thinking aswell but the wipers work perfectly fine 🤔
It does operate that as well but it is on a different circuit
The blinkers and hazard is tied in together
Brakes not as much but on some years it’s possible
Ck for voltage at the brake light switch.
If you have voltage I would say test the switch for continuity when the switch is pressed in.
If the switch is fine and you have voltage
Check the ground to make sure it’s ok
Or run a new ground press the brake pedal see if lights work
Does a e150 van ford have it in same place 1999
Mine was making a buzzing noise lets hope the swap will fix this!
Mine is doing the same thing. Did you fix it?
thx, This is what the problem was. Still works i unplugged it plugged it back in worked good for a little while Doordashing went out one point and came right back on. Thinks its the connection. going to spray wd40 in it later
Quick question when you press the hazard button it's just 2 setting correct..1push for hazards on and 1 push for hazards off. (Have an issue where it is 4 settings with 1 of the settings being no turn signals 10 e350 bus)
That unit needs to be replaced
Liked and subscribed thanks bro.. Keep the F250 videos coming 👍
How can you tell if it's your multi function switch or signal relay?
change the relay they are cheap at autozone you can get 4 there for ONE Ford OE and they are the same. If that don't work then you have to get into the steering column and take out the cluster switch and replace it. Make sure the fuse is good as well (check it first) then flasher then cluster switch. Cheap to expensive. Easy to harder
Hey hoping you can help I have a 2004 Cadillac deville I purchased it like this no hazards ,blinkers or dash indicators I am hearing clicking every time I use blinkers or hazards but nothing happens what do you think ?
Just going to run down some stuff even if you probably check it already
Start with the fuse at the fuse blocks
Check engine compartment and inside cab, look for blinkers and the hazard
Then check the relays for blinkers and the hazard make sure you have power going In and out of fuses and relays.
The if all good you will need to check the blinker unit just because you hear it clicking doesn’t mean it works, they are electronic and that clocking is fake you need to make sure u have the pulse of electric going out .
If all good then you need to start checking the steering column the hazard button and the switch arm for the blinkers make sure they are not worn out
Good luck
@@DavidsHowtosReviews checked fuses and fuse box with light tester I haven’t replaced the turn signal flasher I’m hoping it’s that but if not I’ll look at my steering column like you said thanks for the response
@@motivated_principles1056 hope it’s a easy fix
@@DavidsHowtosReviews me 2 thanks for the supports god bless
So when I turn my hazards on only the green arrow indicating the right side shows up. Neither of my blinkers are working either. Would it be the same issue? I hear the clicking when using my hazards.
Good video! Do you know where is the air conditioner relay located?? Thanks again!
Check the ac fuse inside the cab
Fuse 24. 10amp
That’s for the clutch
Under hood is #36 it is a diode that’s for ac clutch also
Check the ac pressure, if the pressure is to low it will shutdown the system
@@DavidsHowtosReviews OK, thank you, I will do that. I really appreciate it!
Thank you I found it had to dig - Back up and running SAFE!
Anybody got a part number for that flasher?
Would the brake lights not work because of this too?
Try replacing this unit
If you did I would check your fuse and grounds
ruclips.net/video/sYW0cDN4irk/видео.html
What model year?
So will I have to replace the relay if My turn signals don’t work but my hazard light works?
Thank you
Mine is doing the same thing. Did you fix yours?
Did any of you guys do it? My coworkers is like that
Yes most likely
My hazards work, but the blinkers don't. They usually won't work when it's cold or they take a while to work after the truck is warm. Is that the same issue?
Could be the multi switch (it consist of turn signal switch, wiper switch, hazards) or could be wires...check under the dashboard for bad wires
@benl4707 the hazard/blinker switch unit needs to be replaced
It on Amazon
It can also be the flasher unit that unit works by heat
This is what it will look like
Depends on your yr ,make ,model
EP27 Fits for Ford F150 (97-12), F250-F450 (99-10) Super Duty Trucks EP27 Flasher Realy, Fix Hyper Flash, Compatible LED/Stock Bulb Electronic Turn Signal and Hazard Warnning, Flasher Relay a.co/d/b2hGrKW
All this is said assuming you checked the basics 1st
SOLVED! I've read many threads just like this and you guys mostly have my exact problem. Here's what the problem was and how I fixed it:
First, in my 2012 Ford F150 the right blinker (flasher)/ brake light would not work. Turn signal blinked fast inside and for the front light and the mirror signal but tail light blinker would not flash. The bulbs were fine, I even replaced with new just to double down. The tail lights would light up when my headlights were on (running lights) but would not get brighter when brake depressed and would not flash for turn signal.
I will tell some of you to keep in mind that yours may light up also so you don't think you have a bulb out but keep in mind there are two sepperate tungstan filaments (squiggly light wires) in each tail light and the brakes and flasher one could be bad and your running tail lights still work so definately change your bulbs FIRST, then do this if that was not it.
So I had the problem for many months and refused to take my truck to the dealer where of course they will want to replace things and rewire and god knows what else and I've read where one guy says Ford charged him like $800 to fix this. I fixed this problem with $9.00. Saw a RUclips video with a guy with the same problem and he bought an ELM Interface scanner, plugged into the vehicle under the steering wheel and scanned his own truck with an Android app. So I bought the same one on Amazon (here is the link)
www.amazon.com/gp/product/B081WYWZ6B/ref=ppx_yo_dt_b_asin_title_o09_s00?ie=UTF8&psc=1
I found a free app called Car Scanner ELM OBD2 by OvZ it's a generic looking logo of a blue square with a white engine. But I actually saw tons of these apps and I'm sure other apps would work fine as long as they're ELM OBD2 scanning apps with high ratings.
I scanned my truck hoping to see some code come up about the BCM (body control module which is where the problem is) but did not see that code. Didnt matter. I CLEARED what unuseful codes I did see and that immediately fixed the problem and my damn flasher and brake lights are all working again. THANK GOD FOR THIS. Super cheap and easy. I'll never go to a dealership. Hope this helps y'all.
My 2004 f250 burns the fuse as soon as I flash the passenger side. Will the flasher relay help with fuse not burning?
Lucia Aguirre
No
I would check the rear light wires and or the trailer socket and wires if your trailer harness uses same fuse, some of the truck have separate fuses for the trailer electric
@@DavidsHowtosReviews I will check and let you know. thanks
now my truck is burning the fuse as soon as I plug change it to a new few fuse into the fuse box
Lucia Aguirre
That’s a short to ground
So the short is from the steering column where the lever is to fuse box
Did anyone work on the inside of the truck in the steering column?
Or even under the dash by the pedals?
The blinker switch assembly may need to be looked at or even the fuse block
Those are Notorious for water leaking on the fuse block and making truck do wacky things
Even drain the battery for no reason
Or radio to do wacky things
David Behr's Phantom Industries thank you I changed the single switch and it stop doing it. Had a lot of shortages but now all good. Thank you so much for your help.
I have a 2004 F350 and when I use my right or left turn signals my tail lights flash as if I have my hazard lights on could this be because of a bad relay shown in this video?
That sounds more like a ground wire in the back of truck
Check and clean the tail light grounds
Electric finds ground even if it’s going through another bulb to get to it.
Or it’s possible the wires are crossed.
If there was work done on truck I would check to see if something was done to cause this.
I have a f350 2005 i changed the relay but still doesnt work any idea what it is....
You probably have to change out the column switch it incorporates the directional signals and the hazard switch
a.co/d/eooD6ba
Anyone have a part # ?
Or specific name.. trying to order from RockAuto.
1998 E series camper.
Hazards work and turn signals work but I have no clicking sound, (I also have no chime sound when turning the car on) could my problem be related to this part? 2008 Ford Explorer
No
Will be the chime at that piont
I need some help with my 2018 Ford F-150 , Oem Led headlights and the left front blinker stopped working. All others till work. I am at a lost. I am Firefighter not a mechanic, Help ?????
Unfortunately most LED lights don't have bulbs
Check for voltage at pug, if you have voltage u have to replace lens
Or if it has a bulb replace bulb
Did u have brake lights?
Yes
The brake lights are something different
Ck this video out
ruclips.net/video/sYW0cDN4irk/видео.html
Thank you so much!!!!
How much would this fix cost at a shop?
Hard to say
Depends on what is really wrong.
The part / parts and the time.
Few hundred to a few thousand
Get a estimate so u are not blind sided
Good video, although once he used the term "flasher unit " for the relay that he is changing. That may confuse some.
Thanks
I truly hope the people that watch this can keep up or maybe they should not attempt this .. 🤣😂🤦🏼♂️
It all good ..
@@DavidsHowtosReviews Yup, just get your terminology straight. 🤔😣
@@stevecarlisle3323 😂🤣👍
So... my hazards went out the other day and I noticed that the blinkers also went at the same time. Now I’ve realized that my brake lights are out also. I’m guessing they all went out together. I checked the fuse and it’s fine. After looking at this video I’m guessing this is my next step. Do you agree?
And just as a side note... who puts brake lights and blinkers and hazards all on the same unit? Seems like a safety hazard to me 🤷♀️
Yes try this for fist
If this fixes only the blinkers then try the brake switch which is on the brake pedal I have a video on that as well.
If it fixes everything then you’re all set.
And yes Ford does some strange things that is unsafe in my opinion
Everything should be separated especially the hazards
@@DavidsHowtosReviews thanks! 😊
I have the same issue
Is this diferente from the flasher light round fuse? I don’t have signals or break light.mine is a 95. What year does this apply to?
I have the same issue. 2004 F150 Heritage 4.2L 5-speed
What happens if I'm getting power to the relay but no power to the flasher fuse. And the relay isn't clicking and I have no indication lights only dash either
That sounds like ur flasher lever is shot
Check for voltage into the lever and out
If you have voltage in but not out time to replace lever
If u have no voltage in then u need to check for cut wires
Also check the fuse block for sign of water the windshield on these tend to leak onto the fuse block
what could cause my running lights to stay on rather the switch is on or off the only way to turn them off to disconnect the batteries ? if you know the answer it would be appreciated!
The head light switches on these trucks tend to burn up, short out, and get stuck on,
Check the head light switch..
@@DavidsHowtosReviews alrighty so I ordered a new headlight switch and installed it but it didn’t work do you have any other ideas when I turn it on they come on really bright but when everything‘s off they’re still on but you can tell it it’s not at the full power
Before you go crazy
Check the relay make sure it’s not stuck on just swap relays with another that in in the fuse block.
Also check the fuse block under dash, if the windshield leaks it goes right onto the fuse box look for signs of water that has leaked down or whet the roof where the lights are and windshield
You are looking for bad relay first
Water in fuse block second
Last chase the wires for those lights see where it is getting the power.
Good luck
If that’s not to problem you will have to start chasing wires because
Okay
what do I do if only the front right one doesn't work, what do you think is the issue
i think when i go in there i'm gonna see a cut wire in that one spot from the video
@@leviprine9490
I would start with the socket where the bulb is, as long as u roiled out the bulb itself.
If the socket is good not corroded or melted,
Then follow the wires.
Also, dose the blinker work or only the back light?
Check for voltage at plug.
If you have voltage then check the ground.
Good luck
I replaced the socket by borrowing the left one, the back right blinker works, its just the front right not working, the more i think about it the more i think its an isolated thing. I think its some kinda problem between the signal switch on the steering column and the harness for the blinker bulb(I replaced the blinker bulb , theres a crack in the plastic light cover, its a second hand truck I'm trying to maintainence up)
I'll check for voltage at the pluh
@@leviprine9490 did you find a solution my truck is doing the same thing but only my front right one is working my back right don’t work an I replaced the bulb so would a fuse still do that? Or is it something bigger
I changed the relay but still have the same issue what’s the next step
What is the issue,
No blinkers, but hazard, no hazard, but blinkers.
I would definitely check for voltage at both sides of fuse, then ck for voltage at the flasher unit then ck the switch up on top of steering column.
The switch on top of the steering column tends to go bad.
Have an issue I can’t figure out .
My turn signals work just fine , but my hazards don’t ..
Any help would be appreciated thanks I’m advance
I would first check for voltage before and after hazard button, the button tends to wear out but works like it should just dose not let voltage through
If you have cked this already please let me know what u did thus far.
Ok so my hazards still work but it’s just my blinkers that don’t any thoughts
Change this
A-Premium Turn Signal Switch, Windshield Wiper Washer, Hazard Warning Flasher, Multifunction Switch, Compatible with Ford F-150 1999-2003, F-250/350/450/550 Super Duty, Blackwood, YL3Z13K359ABA a.co/d/4KGTSQY
I have similar issue but my hazards work but my turn signals don’t
Mine a 03 lariat, was working hazzards. But turn signals was working sometimes it stoped completely hazArds stay working. Now its nothing.
Sounds like you need to change the turn signal lever,
A few viewers said that it was their lever with similar issue
That worked... thanks bro
I wiggled the relay box and hazards work but blinkers don't
If you have over 100k more then likely it’s the blinker switch on the column.
Also the hazard switch usually where is Al and you need to wiggle the switch for the hazards sometimes it will get everything to work again, but if it does replace the hazard switch.
Also make sure you check the common things like fuses and grounds just in case a wire got pinched by the frame or something like that and popped the fuse.
Unfortunately I did everything that you said in the video and it did go by an oem which was $46 but it turns out that this is not the problem my turn signal still doesn't work but my emergency flashers work's just trying to figure out which are the relays for the Flasher or the fuses is that something you can help me with?
I would start with the directional lever on steering column one viewer said their’s needed to be replaced.
Check for voltage in and out of that.
Check for voltage before replacing parts voltage in, voltage out.
Just make sure all fuses are good
Not that the flasher relay got hot and popped the fuse.
It work good 👍
I have hazards but the turn signals just quit :( any ideas?
That really sounds like the signal lever needs to be replaced
This is the part just make sure to check your application
shop.advanceautoparts.com/p/motorcraft-original-equipment-o.e.-switch-assembly-direction-indicator-sw-6524/11865635-P
I just replace the 2 of them still blinkers not working and i check fuse. no luck
If you have power at fuse
I would say the flasher switch/ arm needs replacement.
If there is no voltage at fuse then there is a problem with ether the fuse block, follow the voltage.
Where is it located on f350
This truck in the video is a F350
What if I don’t hear the click, I press it down nothing happens
I have that problem. Nothing happens when flashers on, except my brake lights don't work. Turn flasher off, brake lights work. No blinker lights or noise. Weird.
Definitely check the ground wires
Sounds like the electric trying to find ground through other wires
i was diagnosing my dads truck signals last night. they werent going, and neither were 2 of the 3 brake lights. weird right? the one on the back of the roof was still ok. meanwhile that freaky buzzy noise you demonstrate was happening cause i left the 4-ways "on" while i was upside down in the footwell. pressed n massaged the 4-way button and for some reason signals n brakes came back. im making him replace this blasted fuse tomorrow. 😎
Sorry for late response
I hope things went well with the fix
Electrical problems can be a little tricky
What is this part called
adrian silva
Flasher relay.
On my 2000 F150 it's on the left side not right of steering wheel
Glade you found it.
Off and running again
Neither of my turn signals work, and when i use my hazards only the left side comes on
That sounds like the turn signal lever and assembly needs to be replaced
That didn’t work
Any idea what I could do now?
Depending on how many miles
The blinker lever assembly
Replaces the blinker lever and the hazard button
So my hazards nor blinkers work they stopped all a sudden
You probably need to change out the hazard/blinker/high beam unit on the steering column
@@DavidsHowtosReviews going to go over everything tomorrow just had to replace the light control module few months back
Yeah that's about the last thing it could be I might just take it and have it done
Nah it’s very easy
Two screws and two plugs
I have been meaning to get a video up on how to change out the unit
What if the indicators come on but they stay solid and don’t blink?
ColMustard 1820
Your flashing relay needs to be replaced
That is another thing that happens when the flasher relay goes bad
You may have a BCM issue which you can fix for $9 with a scanner and a free app. See my other comment here on this video comment thread for full explanation
If they stay solid and dont blink but inside your signal is blinking fast its probably your BCM. Scan it and clear the code yourself with a cheap scanner. Easy cheap fix
Could be bad ground I had that problem as well and that's what it was
Thanknyou
This work to for 150 2003
I have the same problem
Moises Tejada
One good thing about Ford they keep everything the same 😊
David Behr's Phantom Industries
A question that year and model is the car you show in the video
Moises Tejada F350 2003’ super duty 7.3L power stroke
My hazards work, but my directionals don't. I replaced the relay..
Check for voltage coming out of the column blinker shifter, it may need to be replaced
It's not a relay, it's a flasher like on Christmas tree lights. .
That’s big thermal flasher? Under dash panel fuse.
Get the oem
They are more electric now but yes same thing
@@DavidsHowtosReviews like my hazards and turn signal lights will be working on the outside of the vehicle, but I don’t see them working on the inside on the dash. Could it be the thermal flasher right?
That sounds like you have something going on with the wire leading to dash or the lights inside the dash for the indicators are burnt out
Ck for voltage at input for the dash
I tried this and it didn't work. Need to do more diagnostics before I go out and spend money.
Always best to troubleshoot as u go so you don’t waste money
Came to this video cuz my blinkers only work when the hazard button is pressed down but the hazards don’t work
I would think this blinker hazard unit is bad as long as you made sure there are no wires cut or crossed
www.1aauto.com/ford-turn-signal-combination-lever-trq-swa41775/i/1azcc00017
My hazards work but turn directionals don't.
Check the directional switch it may need to be changed
@@DavidsHowtosReviews It was the flasher relay.
My left blinker wasnt working all i did was move steering wheel up
u5
Thanks so much!!!!!