you save my life，omg i just sad like 3 day already，because i play horizon 5 and get down about this problem。 you derserve my follow and like， thx man。sry about my 6 years old broken english have a nice day！
Beautiful! Picked one up used from marketplace and the clutch was dead and break only worked half way... A vacuum, hot glue, and WD-40 and it's running great with full response from the clutch now. Next it's the loose steering wheel but I'm able to drive properly now!
@@floorit27 I didn't feel like buying a hot glue gun. all i did was put a paper towel between the potentiometer and the plastic casing, so that it would prevent movement. this fixed the issue.
Thanks for this great video man, I was about to tore my savings by buying a logitech wheel due to issues on my pxn v9 pedals. the gas pedal is in 30% and the clutch at 60% all the time. Hope I can fix it with this procedure
An issue my accelerator had is the potentiometer wasn't installed correctly to begin with, so I'd only be getting 85-90% at best. I did some fiddling with the angle it was sitting at and now it works just fine.
i checked my gas pedal and nothing was moving that shouldnt be moving. i cleaned it and calibrated it but this flickering problem is still there. pls help i dont know what to do.😮💨😕
Backstory, I know very little of sim racing set ups and bought this wheel about 3 months ago. Everything works fine after fixing this problem, but like you said in some other comments, it's probably bound to happen again. Before that happens, I was gonna look into buying one of the better pedal sets, something like the clubsport or something similar. My question is, if I find pedals that use the same output as the PXN-v9 pedals, would I be able to theoretically plug them in and play keeping the original V9 Wheel + Shifter? Ofc app compatibility afterwards may be questionable maybe. I would like to know for sure before I spend 300 on a pedal set I can't use yet, and I can't find anything on the internet about it.
On PC I would imagine if you had pedals that connected as a separate device, it's likely they will work in a way, just like your controller and mouse and keyboard all work at the same time. I can't remember who, but one of my followers was going to make their own pedals. I've never heard how it turned out. As for what plugs into the controller as a direct replacement, as long as it sends the same data the original potentiometers send(or have the same potentiometer), it should work. You could use the original wire to make a pigtail for the connection to the controller. It would most likely have to be homemade if connecting directly to the controller. The software for the controller limits that. Best case scenario is the game you want to play allows the simultaneous input of new pedals and the og shifter and at the same time. If the fix doesn't work for you, I think the product might just not be up to par with your expectations. I haven't tested many other products, so I don't have other recommendations.
my pedals aren't giving me full range of motion (it's with the throttle), I can wiggle the pedal around to try and find full motion, but it's not ideal when racing and I just end up losing positions. could you possibly tell me what I could do? any and all would be much appreciated👍 Also, I am playing on playstation.
Thanks for the video . I bought one of these just a month or two ago and used it less then 10 times for ETS 2, never used it roughly and put it aside until yesterday when I plugged it in I noticed that my acceleration was less and less going to a dead stop, then it started working again ,then same thing happened. I was struggling to go at 10 km/h with pedal to the floor. The brake is fine and I haven't used the clutch or gear shifter so far since I bought it. I'm hoping this video solves the problem but pissed that there is a problem in the first place especially since its hardly ever been used. And I don't think mine is a dirt issue as after its used I put it aside and cover it with a cloth to protect it from dust. Any ideas what the problem could be? ......ok Its the next day now I opened it up and did as you did in the video and it seems fine now. I added a little glue to the top sides of the little circuit to hold it down better .Just gave it a test run on an ETS 2 delivery run and everything is ok. Thumbs up to you pal.
Clutch pedal went out. Turns out the Clutch chip cant disengage and stays around 60 - 69% engaged when not touched. However it works fine when being pushed. Just wont disengage. i think the chip is the problem
Take it out and spin it outside of the pedal and see what you get. I am talking to them now about getting new pedals because A. I want to see if they send me something half decent and B I'll have extra parts. The potentiometer's are cheap from what I hear but that should also mean cheap replacement... They are accessible enough. But I'm almost at the point of taking this whole video back and saying talk to the manufacturer, as its almost a luck of the draw thing with this type of design.
I have a question about the PX V9 because I bought it and a couple months later everything works but my pedals and shifter are not responding in game but when I test it in the app they work how do I fix this?
copied from other video: thanks, mine also works better after just blowing it myself using my mouth lol, but apparently my potentiometer at the acceletor/throttle paddle is loose so I just lay in a plastic wrap (MAMEE wrapper lol) in between and voila it works fine, but unscrewing all those screws are annoying af tho, in other words try inserting a plastic wrapper folded to give more thickness and tension on the potentiometer board, mine works like a charm after. be careful not to damage the circuit especialy the tiny resistor tho.
all of my pedals are jacked up and Ive had no issues since I got it for christmas. My brake is the only one that slightly works. Anything I can do to fix them?
This sounds like a wire issue! the main wire. Did they all get wack at once? Or kinda over time? The less likely answer if the issue didnt occur all at once is its dirty af, take it apart and get an "elecronic cleaner" spray and paper towels and go to town cleaning. Many people have issues because there are large gaps for dirt to get in. If they all went bad around the same time: Check the main cable coming out of the unit by taking it apart like in this video. Check it for obvious damage where it comes out. You likely won't see any though but you could see a kink in the wire. I would (not saying you techincally should) but I would then cut the wire an inch away from where it comes out of the sytem both on the inside and the outside cutting away any part of the wire that may have been bent too hard. Splice/solder the wires back with their respective pairs, tie a knot in the cable, and leave the knot inside the divice, as to prevent to cable from being pulled out of the unit.
@@floorit27 over time. Me and my dad looked at in insides and took each potentiometer out and tested them without the pedal. The clutched died there but the others were the same. We put everything back together and I recalibrated them and they were fixed. Idk what it was but they are fixed now
Anyone know what is wrong with mine the acceleration works fine but the clutch and brake are set as the same pedal and I can use the shifter any tips for it I'm playing beam ng drive btw
I’m was having an issue that this video fixed so thank for that but I’ve been having this other issue where the pedal doesn’t start responding until it’s pushed down a little far so if you have a solution for that that would be amazing
Hey when I go into calibration and press the pedals I get no response at all only getting response from the steering wheel any idea what can be going on also my pedals are only break and gas
Switch the steering wheel mode. It starts at an Xbox controller mode. Once you switch it, it will be the PC input version. Hopefully I understoof the issue correctly.
Hey man what's up every time I glue the thing it works and it gets better and it fixes itself but after some use after like 15 minutes 20 minutes it goes back to fluctuating so did that happen to you?
I did this and it helped A LOT but whenever I press the gas in game it breaks and when I press the brake it still brakes and the clutch works perfect any way I can fix it?
It's probably only happening in certain cars because of the different transmissions+traction control. You should follow the video to take it apart and see if you can clean it first
I have the same steering wheel and a few days ago it stopped working because when I plug it into the computer (pc) in the application to connect it, it takes it as a play station, something that did not happen a few days ago, how can I solve it, does anyone know anything?
Hello. I know that it worked for some people, but my acceleration pedal became worse. I could throttle up to 100%, but going there from 0% became more rough. Are there possible things I may have done wrong?
If you're sure the potentiometers are not moving, then the next step would be the calibration. It sounds like now that you have reseated it, the potentiometer has a new position. Calibration will set what position is 0 and what is max. Let me know if that works!
I'm having troubles with connectability let's just say I'm playing BeamNG drive it will not boot up saying device not recognize and shut down the wheel
Wire issue is the first suspect. Do you have a different system you can test this on? If you do it can help determine if the wires are good or bad and go from there. As it could be a PC power save issue or USB issue. The software conflict would be resolved in Windows Device Manager. Try updating the drivers
Almost every game requires the secondary set of controls the controller comes with. The first input is like a legacy xbox input. If you hold the mode button I believe it is, for 3 seconds or so, it switches.
You do need to make sure the controller is in the right mode. There's a little quick start guide it comes with that details switching it so it has the proper inputs.
(my best tip at the end, got carried away typing) That sucks. This is really kinda cheap but the next steps up are far more money. Good for the money... On the bright side, if you're within a year you may be able to replace it! Contact them! On the other bright side, there are really cool ways to mend plastic. One of them is heating up metal rods like paperclips in the shape of stiches and meltng them into the plastic. This requires probably a bit of practice. I would get JB Weld quick set Epoxy. They have a 5 minute 2 part epoxy that hardens very well. Start with tiny bits and have the peices held together well and let them sit for hours. Then add a little more glue, slowly painting more and more on to add layers. Stuff dries harder than the plastic they use!
Completely? If you are in warranty, see if you can get a replacement. I would personally look into getting a replacement potentiometer. You can test the potentiometer itself by removing it from the pedal and spinning it in your hand while watching the display from the link in the video description.
Hello brother i hope you reply back I got my pxn v9 working and i only use once My grandpa die and i didnt use my pxn for a week and now i try it my pedal aint working steering wheel and shifter working very well but the pedal didnt work this is almost brandnew can you help with this?
![Felix "Unfair" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/Oswujxm2Ag0/mqdefault.jpg)
amazingly, this actually helped 2 years after posting. thanks bro!
you save my life，omg i just sad like 3 day already，because i play horizon 5 and get down about this problem。 you derserve my follow and like， thx man。sry about my 6 years old broken english have a nice day！
Easy to read, you're fine! I'm happy the video helped!
Thank you so much, I was annoyed for like a whole week because I couldn’t play assetto corsa without my sim racing setup working properly.
The pain of non working controls.
@@floorit27my pedals do work, but I only can drive very slow in assetto
i know you have probably seen this a lot but thanks yo i'm glad that there is someone out there that has a solution to this problem.
I enjoy it every time I see it!
Beautiful! Picked one up used from marketplace and the clutch was dead and break only worked half way... A vacuum, hot glue, and WD-40 and it's running great with full response from the clutch now. Next it's the loose steering wheel but I'm able to drive properly now!
Awesome!
You're awesome man. A little WD-40 on the springs and some hot glue later, and mine actually works better now than it did when I bought it. Thanks.
Really awesome to hear. Every time!
I’m 100th subscriber let’s gooo
I didnt try this yet, but even if it doesn't work, your explanation was clutch. I never understood what the problem is.
Easy just turn it around shake a little bit hit it with something and it probably get fixed because the issue is the potentiometers
this is the exact same problem my pedals have, i'll try your solution and hopefully i don't have to buy a new pedal set 👍 thanks a lot
So far I've heard good news from 99% of people with this fix. Hopefully it works for you.
@@floorit27 I didn't feel like buying a hot glue gun. all i did was put a paper towel between the potentiometer and the plastic casing, so that it would prevent movement. this fixed the issue.
Thanks alot brother. I fixed mine
hi bro my clutch is not working when i tried it in the app its not detecting any signal
Hello, there is a problem why if you squeeze out the clutch and add even a little gas, the clutch pedal immediately disappears
It is a resistance problem …
what goes wrong with all these IS THE POTENTIOMETERS
Thanks for this great video man, I was about to tore my savings by buying a logitech wheel due to issues on my pxn v9 pedals. the gas pedal is in 30% and the clutch at 60% all the time. Hope I can fix it with this procedure
If not it might be worth a shot reaching out to them, support@e-pxn.com
An issue my accelerator had is the potentiometer wasn't installed correctly to begin with, so I'd only be getting 85-90% at best. I did some fiddling with the angle it was sitting at and now it works just fine.
Hey, is your clutch staying at 50% ? If so how would I fix it
Did you fix it ? I have the same problem in Forza games
@@zazahorros9063 i fixed it in beam ng btu im not sure what to do on forza as i dont play the game
i checked my gas pedal and nothing was moving that shouldnt be moving. i cleaned it and calibrated it but this flickering problem is still there. pls help i dont know what to do.😮💨😕
OMG i just fixed it xD. the issue was that this electronic thing wasnt properly glued together and was kinda angeled🤣🤣
Backstory, I know very little of sim racing set ups and bought this wheel about 3 months ago. Everything works fine after fixing this problem, but like you said in some other comments, it's probably bound to happen again. Before that happens, I was gonna look into buying one of the better pedal sets, something like the clubsport or something similar. My question is, if I find pedals that use the same output as the PXN-v9 pedals, would I be able to theoretically plug them in and play keeping the original V9 Wheel + Shifter? Ofc app compatibility afterwards may be questionable maybe. I would like to know for sure before I spend 300 on a pedal set I can't use yet, and I can't find anything on the internet about it.
On PC I would imagine if you had pedals that connected as a separate device, it's likely they will work in a way, just like your controller and mouse and keyboard all work at the same time. I can't remember who, but one of my followers was going to make their own pedals. I've never heard how it turned out. As for what plugs into the controller as a direct replacement, as long as it sends the same data the original potentiometers send(or have the same potentiometer), it should work. You could use the original wire to make a pigtail for the connection to the controller. It would most likely have to be homemade if connecting directly to the controller. The software for the controller limits that. Best case scenario is the game you want to play allows the simultaneous input of new pedals and the og shifter and at the same time. If the fix doesn't work for you, I think the product might just not be up to par with your expectations. I haven't tested many other products, so I don't have other recommendations.
my pedals aren't giving me full range of motion (it's with the throttle), I can wiggle the pedal around to try and find full motion, but it's not ideal when racing and I just end up losing positions. could you possibly tell me what I could do? any and all would be much appreciated👍 Also, I am playing on playstation.
you're a legend man, thank you🤍
Glad to help!
I’m having the same issue but I couldn’t understand where you glued the potentiometer, did you glue it to where it goes, like where it sits? Thank you
Hii… does anyone here p KNOWS WHERE TO PURCHASE THE POTENTIOMETERS?? I couldn’t
Still trying to find out… i actually believe thats the issue… not the shaft play
Thanks for the video . I bought one of these just a month or two ago and used it less then 10 times for ETS 2, never used it roughly and put it aside until yesterday when I plugged it in I noticed that my acceleration was less and less going to a dead stop, then it started working again ,then same thing happened. I was struggling to go at 10 km/h with pedal to the floor. The brake is fine and I haven't used the clutch or gear shifter so far since I bought it. I'm hoping this video solves the problem but pissed that there is a problem in the first place especially since its hardly ever been used. And I don't think mine is a dirt issue as after its used I put it aside and cover it with a cloth to protect it from dust. Any ideas what the problem could be? ......ok Its the next day now I opened it up and did as you did in the video and it seems fine now. I added a little glue to the top sides of the little circuit to hold it down better .Just gave it a test run on an ETS 2 delivery run and everything is ok. Thumbs up to you pal.
Good work!
Clutch pedal went out. Turns out the Clutch chip cant disengage and stays around 60 - 69% engaged when not touched. However it works fine when being pushed. Just wont disengage. i think the chip is the problem
Take it out and spin it outside of the pedal and see what you get. I am talking to them now about getting new pedals because A. I want to see if they send me something half decent and B I'll have extra parts. The potentiometer's are cheap from what I hear but that should also mean cheap replacement... They are accessible enough. But I'm almost at the point of taking this whole video back and saying talk to the manufacturer, as its almost a luck of the draw thing with this type of design.
I have a question about the PX V9 because I bought it and a couple months later everything works but my pedals and shifter are not responding in game but when I test it in the app they work how do I fix this?
Oh my God,thank you so much
copied from other video: thanks, mine also works better after just blowing it myself using my mouth lol, but apparently my potentiometer at the acceletor/throttle paddle is loose so I just lay in a plastic wrap (MAMEE wrapper lol) in between and voila it works fine, but unscrewing all those screws are annoying af tho, in other words try inserting a plastic wrapper folded to give more thickness and tension on the potentiometer board, mine works like a charm after. be careful not to damage the circuit especialy the tiny resistor tho.
This plastic wrap idea is great
all of my pedals are jacked up and Ive had no issues since I got it for christmas. My brake is the only one that slightly works. Anything I can do to fix them?
This sounds like a wire issue! the main wire. Did they all get wack at once? Or kinda over time?
The less likely answer if the issue didnt occur all at once is its dirty af, take it apart and get an "elecronic cleaner" spray and paper towels and go to town cleaning. Many people have issues because there are large gaps for dirt to get in.
If they all went bad around the same time: Check the main cable coming out of the unit by taking it apart like in this video. Check it for obvious damage where it comes out. You likely won't see any though but you could see a kink in the wire. I would (not saying you techincally should) but I would then cut the wire an inch away from where it comes out of the sytem both on the inside and the outside cutting away any part of the wire that may have been bent too hard. Splice/solder the wires back with their respective pairs, tie a knot in the cable, and leave the knot inside the divice, as to prevent to cable from being pulled out of the unit.
@@floorit27 over time. Me and my dad looked at in insides and took each potentiometer out and tested them without the pedal. The clutched died there but the others were the same. We put everything back together and I recalibrated them and they were fixed. Idk what it was but they are fixed now
@@ryanebel3707I used it on GTA 5 today i tested it no movement on the pedals
Anyone know what is wrong with mine the acceleration works fine but the clutch and brake are set as the same pedal and I can use the shifter any tips for it I'm playing beam ng drive btw
I’m was having an issue that this video fixed so thank for that but I’ve been having this other issue where the pedal doesn’t start responding until it’s pushed down a little far so if you have a solution for that that would be amazing
That is the calibration I mentioned. Have you done the calibration? Glad it works better. Keep working at it.
my white wire that is connected to accelerate pedal got cut is it game over for me ?
(Use trad french to english) il faut acheter de la pâte à souder et la chauffer avec le cable
can we have a tutorial for the steering wobbling?
Hey when I go into calibration and press the pedals I get no response at all only getting response from the steering wheel any idea what can be going on also my pedals are only break and gas
try switching the mode
mine doesn't work on Xinput since it's been used with x360ce mapping, but all buttons on Dinput work, please provide a solution...
Switch the steering wheel mode. It starts at an Xbox controller mode. Once you switch it, it will be the PC input version. Hopefully I understoof the issue correctly.
You my hero
Mine says that I'm pressing down on it even though I'm not would this problem be fixed by doing this?
I have a very annoying sound in them, I own a hori apex. The gas and the break. how do i fix that for no annoying sound more?
I'd assume it's similar to these. A non conductive grease might help
Hey man what's up every time I glue the thing it works and it gets better and it fixes itself but after some use after like 15 minutes 20 minutes it goes back to fluctuating so did that happen to you?
I did this and it helped A LOT but whenever I press the gas in game it breaks and when I press the brake it still brakes and the clutch works perfect any way I can fix it?
Could be on the wrong mode. Try switching the mode
I can’t get my petals to work how do you set it up when you first use it?
Try using the mode button. Look for it in the quickstart guide, only one mode will work in each game or device normally
I can't to open the pedal cover
Did you remove the rubber pads? They cover screws.
@@floorit27 Yes, I removed it
When i driving certrain cars it keeps hitting the max rpm in all gear do you know how to.fix it ??
It's probably only happening in certain cars because of the different transmissions+traction control. You should follow the video to take it apart and see if you can clean it first
@@floorit27 yo but in my assetto corsa my clutch is always half way compare to the throttle
@@hasdevsingh6009 PXN-V9's clutch is always set at 50%. You will have to modify the deadzone of the clutch in game to 50% to cancel it out
I have the same steering wheel and a few days ago it stopped working because when I plug it into the computer (pc) in the application to connect it, it takes it as a play station, something that did not happen a few days ago, how can I solve it, does anyone know anything?
Sounds like the mode changed if it things it's a Playstation controller. Try changing the mode! Sorry for the late reply.
Same trouble thanks for information
Glad it helped!
Hello. I know that it worked for some people, but my acceleration pedal became worse. I could throttle up to 100%, but going there from 0% became more rough. Are there possible things I may have done wrong?
If you're sure the potentiometers are not moving, then the next step would be the calibration. It sounds like now that you have reseated it, the potentiometer has a new position. Calibration will set what position is 0 and what is max. Let me know if that works!
I'm having troubles with connectability let's just say I'm playing BeamNG drive it will not boot up saying device not recognize and shut down the wheel
Wire issue is the first suspect. Do you have a different system you can test this on? If you do it can help determine if the wires are good or bad and go from there. As it could be a PC power save issue or USB issue. The software conflict would be resolved in Windows Device Manager. Try updating the drivers
Hey, when i hit the gas, it's doing another button and i don't know how to fix it. Do you have an advice?
Almost every game requires the secondary set of controls the controller comes with. The first input is like a legacy xbox input. If you hold the mode button I believe it is, for 3 seconds or so, it switches.
I looked it up, here ya go, page 5
www.e-pxn.com/sites/pxn/files/product/manual/pxn-v900.pdf
I have a problem with mine where the brake pedal works as the gas pedal but also the gas pedal works as a gas pedal
And I’m on console
Hold the "PROG" button for 3s and than the "OPTIONS" button maybe the Reset works on you
You do need to make sure the controller is in the right mode. There's a little quick start guide it comes with that details switching it so it has the proper inputs.
Sorry I looked it up for another comment so here, page 5
www.e-pxn.com/sites/pxn/files/product/manual/pxn-v900.pdf
For some reason my accelator is lagging I did a test with my controller accelerator and the controller accelerator was working better
I would take the potentiometer out and rotate it by hand and watch what it does.
My acceleration is going to halfway and won’t go to max
My pedals just completely broke in half :/
(my best tip at the end, got carried away typing) That sucks. This is really kinda cheap but the next steps up are far more money. Good for the money...
On the bright side, if you're within a year you may be able to replace it! Contact them!
On the other bright side, there are really cool ways to mend plastic. One of them is heating up metal rods like paperclips in the shape of stiches and meltng them into the plastic. This requires probably a bit of practice.
I would get JB Weld quick set Epoxy. They have a 5 minute 2 part epoxy that hardens very well. Start with tiny bits and have the peices held together well and let them sit for hours. Then add a little more glue, slowly painting more and more on to add layers. Stuff dries harder than the plastic they use!
thank you
Uhm i think my sensor itself is broken, i have it alone and it doesnt work properly
Taking it out and spinning it, if its not moving or jumpy its probably toast.
My gas peda stopped working
x2
Completely? If you are in warranty, see if you can get a replacement. I would personally look into getting a replacement potentiometer. You can test the potentiometer itself by removing it from the pedal and spinning it in your hand while watching the display from the link in the video description.
Sorry for the late reply guys, but like i said to FARMBOY, warranty, or soldering a new potentiometer.
@@floorit27 I bought it off of a buddy so no warranty
You save me
Yesss! This helped? Glad to hear
anyone else not able to get the potentiometer back into place
Any luck?
i just want to make the pedals more ferm
Hello brother i hope you reply back
I got my pxn v9 working and i only use once
My grandpa die and i didnt use my pxn for a week and now i try it my pedal aint working
steering wheel and shifter working very well but the pedal didnt work
this is almost brandnew can you help with this?
do you have a FB page?
I got off FB more recently for the complications it presented to do fb youtube and twitch at the same time, and i never got viewers
Спасибо,помогло
the pxn v9 pedals is trash
For the money, id buy them again, but id probably buy a warranty if i didnt plan to fix them again. This is bound to happen again
This thngs is trash yeses
i am not doing allat!
hey any how can I make my pedals feel more stiffer? I just got mine new and I'm kinda scared to mod it because I might break it
when i use it it always makes me push it all the way down same with brakes