it was a test... he was probably intentionally trying to break the machine to see its limit... better break it now in his shop before sending it to the customer...
اني من العراق احب اصنع سيارات اريد اصنع سياره الحلبه بس تجربتي دتفشل بي صنعت سياره الحلبه ممكن انو تصنع سياره الحلبه او تنزله على اليوتيوب اكون ممنون منك او اتشد له محرك روبن او اتكون اصغيره مو كبيره ممكن
Outstanding job Mr i& My Bros suscribe we Lear a lot from your videos keep on,could You share more about electric motors & bike,mini motos convertion a tutorial & links Ford partes thanks Say hello Joe,from panamá.
You are one of if not the best engineers on RUclips. But why do you still work on the floor after all these years looool. You could build a table to work from meybe???
Like everyone else I want to know where to source the linear actuator used. I found a few similar units on Aliexpress, etc. but most had less than 12" maximum extension and this looks to be closer to 36" to 48"
It's not actually a linear actuator. It's a self contained hydraulic unit. The thing on the side of the cylinder is actually a small hydraulic pump and reservoir. I have seen self contained hydraulic units out there but none this big. I would really like to know where he got it.
If you put a nut on the bolt you wish to cut, when you remove the nut, it will clean the threads you cut. If you want to round the end of the bolt, do it before you remove the nut, for the same reason.
piston bağlantısı üstüne takviye (90derece) şart. Kolların başlangıçtaki açılarına göre bağlantılarınada takviye gerekli. Elinize sağlık başarılı bir uygulama olmuş. Fakat bu makineleri insan için kullanmak hayati risk oluşturur lütfen dikkat edin.
Un excelente trabajo, una gran herramienta muy fácil de usar. Felicitaciones y muchas gracias por compartir tu ingenio y talento un saludo desde España 👍
Cuando uno deside mostrar algo para que lo vean por respeto debe responder las preguntas de lo usuarios como no le duele ver el mundo de personas que le piden informacion y ud ni siquiera contesta salvo cuando alguien le da una 🕐 nformacion que le interesa pero solo a ud si va a seguir siendo egoista mejor no muestre nada y asi salvará a mas de una persona a quedarse con dudas
I’m surprised it’s holding so much. Looks like it should tip over. I like the design, I’d just add a counterweight &/or extend the base to make it more stable.
That is really cool but he should not be lifting it so high until he gets too where he is storing it. It becomes very top heavy and could tip over if he hits the right bump. Always lift it to the proper height when you get to its storage spot. Also the video could have been a little shorter if he didn't raise and lower the forks 50 times.
Hello, my name is Angelo and I am writing to you, with the help of an online translator, from Italy. Would it be possible to have technical specifications, a name, where did you buy it.... I'm talking about the battery-operated electrohydraulic piston, and to know the battery of how many volts is it? Thank you
Very well done! Good equipment,. But I would use a table, to help facilitate my work and the stress on my body. special when you have a bad knees, .. Not on the floor ! Too much water fluid no the floor. and be on you knees is not easy. 👍 Great job . I hope I will try one day.! Make lot's of money 🤑 kkkk
Usually pay attention to the oiling and waxing of the contact parts of the movable joints//Because I watch your video and there is a noise when operating the machine//If this is just a test product (don't consider the above link)//But if you want to sell it in the future, you need to The additional bearings will be used for activities.//Of course it might be good to add some springs ((guess)) and nice job
Buenas noches buen trabajo maestro una montacarga que supera la capacidad de 100 kilos a más y tiene patines para movilizar buena herramienta de apoyo en tareas rudas saludos desde Perú
@creative Channel Please sir, I am a mechanical engineering student and my final year project topic is related to what you just produced. Please can you give me the contact address or phone contact of where you got the hydraulic lift from? It is very urgent sir.. Thanks in advance
Never move heavy loads at high lift. Move them low, then raise them when you get to the destination as needed. "Gravity always wins".
it was a test... he was probably intentionally trying to break the machine to see its limit... better break it now in his shop before sending it to the customer...
Try to lift a car
JCB making
اني من العراق احب اصنع سيارات اريد اصنع سياره الحلبه بس تجربتي دتفشل بي صنعت سياره الحلبه ممكن انو تصنع سياره الحلبه او تنزله على اليوتيوب اكون ممنون منك او اتشد له محرك روبن او اتكون اصغيره مو كبيره ممكن
Please can you help me for a making buggy
Second 🥈
Anti-slip mats would also be nice on the forks and a safety bar on the helmet board for your lift function
ps: really cool work
I. Am second
Great and useful project! Looks like it even got wife approval!
1
Лол
I need one build for my shop! Every nice project for the home use , saves for BACK pain manual lifting. Super Job my friend.
hello, can you please share the measurements?
Iam first viewer
Are there any blueprints for this? Would be cool to build one, but would be nice to have some measurements to go off of.
Broo which actuator is this can u share the link to buy it
Sou do Brasil rj com faço para comprar um triciclos eletrônico tem imail telefone ☎️
If you use 2 hydraulic you can better smother tu lift object
Outstanding job Mr i& My Bros suscribe we Lear a lot from your videos keep on,could You share more about electric motors & bike,mini motos convertion a tutorial & links Ford partes thanks Say hello Joe,from panamá.
You are one of if not the best engineers on RUclips. But why do you still work on the floor after all these years looool. You could build a table to work from meybe???
I wonder if You´d mind to share the parts list, it could be great to have also the suppliers list, great work, thanks a bunch for share it
*Congratulation & Good luck 💡*
👈Greeting from *TRIK SIMPLE* 🇲🇨
What is hydraulic motor specifications and cylinders pls share
Like everyone else I want to know where to source the linear actuator used. I found a few similar units on Aliexpress, etc. but most had less than 12" maximum extension and this looks to be closer to 36" to 48"
It's not actually a linear actuator. It's a self contained hydraulic unit. The thing on the side of the cylinder is actually a small hydraulic pump and reservoir. I have seen self contained hydraulic units out there but none this big. I would really like to know where he got it.
Please bro give more car make vedio
Hey man.. Why don't you finally make a work bench??? If those tiles had a mouth they would scream so far
żadnego poszanowania dla przepisów BiHP, wręcz instruktaż jak nie należy robić
How much weight could this hold please comment back would like to know thank you
Please give measurements
If you put a nut on the bolt you wish to cut, when you remove the nut, it will clean the threads you cut. If you want to round the end of the bolt, do it before you remove the nut, for the same reason.
can you share schematics?
Nice project.... where do you buy the hydraulic cylinder with pump ? Any link or do you sell it ?
Yea. Good question.
Sensacional, que alegria descobrir o seu canal!
Your arte is so cool
Very nice.....where i can buy that type electric hydraulic actutator?
Wow cool
First view and first like
piston bağlantısı üstüne takviye (90derece) şart. Kolların başlangıçtaki açılarına göre bağlantılarınada takviye gerekli. Elinize sağlık başarılı bir uygulama olmuş. Fakat bu makineleri insan için kullanmak hayati risk oluşturur lütfen dikkat edin.
amazing video
👍👍👋👋🇮🇹🇮🇹
muy buen trabajo ahora cuanto cuesta esa botella hidráulica, batería y materiales seguro que mas de 1000€ a parte el trabajo
Lo investigaste??? Ahora quiero saber😁
Good idea
C'est meilleur transpalette improvisé 👏
Un excelente trabajo, una gran herramienta muy fácil de usar.
Felicitaciones y muchas gracias por compartir tu ingenio y talento un saludo desde España 👍
Esse é bom.mesmo 😂😂😂 para teste usa a mulher para mostrar que ficou top😂😂
Excelente invento amigo patentelo por que si no le roban la idea
Tôi có thể biết mua thủy lực điện ở đâu và nguồn tài chính không?
Cuando uno deside mostrar algo para que lo vean por respeto debe responder las preguntas de lo usuarios como no le duele ver el mundo de personas que le piden informacion y ud ni siquiera contesta salvo cuando alguien le da una 🕐 nformacion que le interesa pero solo a ud si va a seguir siendo egoista mejor no muestre nada y asi salvará a mas de una persona a quedarse con dudas
Good
Love the way you got the wife up there to test it first…then added an extra steel bar afterwards!!!!!
It's not a work I developed myself...
The number of views is higher than the person who created it..
You can add parallel weight in the back of Handle Forklift for remain balanced So as not to fall forward
Good pièce of work. Forklift and manlift in one, its polyvalent.
Do you share plans? I would be interests in having a go at it.
Muito top, parabéns jovem!
I would like all of the measurements for this please
Super super 👌👍👍 great . work 👍
Gran proyecto, una pregunta cuáles son las especificaciones del motor, saludos desde Guatemala
What are the specs on the actuator?!
Where did you buy the hydraulic ram
Please tell me that what is that black thing
Pls share the actuator link ..i m working on this project
Were you able to source one? Appreciate any pointers. Coming up dry.
Please give me a link to the seller of the hydroulic actuator, boss......
I’m surprised it’s holding so much. Looks like it should tip over. I like the design, I’d just add a counterweight &/or extend the base to make it more stable.
i also have the same doubt.
when the forks in lifted position, it is almost one feet away from the base. that may cause tip over...
Good idea as long as to make sure the center of gravity being maintained behind the front wheels.
Yea , i'm a bit scared . It look like a disaster waiting to hapen, you can't count only on the weight of the lift from falling.
You are doing some wrong things. The first and most important , you must wear safety shoes and glasses, but i see you dont care about that.
That is really cool but he should not be lifting it so high until he gets too where he is storing it. It becomes very top heavy and could tip over if he hits the right bump. Always lift it to the proper height when you get to its storage spot. Also the video could have been a little shorter if he didn't raise and lower the forks 50 times.
😃👏👏👏👏👏
👍👍👍👍👍
EXCELENT!
Your projects were too costly 🙂😌😌😌............
Excellent fabrication skills with technical knowledge!
Don't know if I can trust equipment made by someone wearing sandals in the workshop 😊
Where can I find this hydraulic system with DC motor?
Mantap lek..
where did u gt that hydraulic lift? want to know
Hello, my name is Angelo and I am writing to you, with the help of an online translator, from Italy. Would it be possible to have technical specifications, a name, where did you buy it.... I'm talking about the battery-operated electrohydraulic piston, and to know the battery of how many volts is it? Thank you
They make a nice product but they never have the plans on line or available or tell where they get the parts from
Very well done! Good equipment,. But I would use a table, to help facilitate my work and the stress on my body. special when you have a bad knees, .. Not on the floor ! Too much water fluid no the floor. and be on you knees is not easy. 👍 Great job . I hope I will try one day.! Make lot's of money 🤑 kkkk
I thought I was the only one that welds and cuts wearing flip-flops
Usually pay attention to the oiling and waxing of the contact parts of the movable joints//Because I watch your video and there is a noise when operating the machine//If this is just a test product (don't consider the above link)//But if you want to sell it in the future, you need to The additional bearings will be used for activities.//Of course it might be good to add some springs ((guess))
and nice job
Where would you put the springs?
The bearings I agree with you.
@@3251969ROSARIO in (09:06),(22:03) move Time.
There's,(try),
What is the crane parts metal specs?
Buenas noches buen trabajo maestro una montacarga que supera la capacidad de 100 kilos a más y tiene patines para movilizar buena herramienta de apoyo en tareas rudas saludos desde Perú
Where did you buy the hydraulic ram
Make homemade plane
This was awesome! What kind ot hydraulic actuator do you use here?
He's good at building things without instructions
Excellent super just excellent
Itu namanya hollo apa bang?
Seems like the main lifting arm (2"x4" box) being 4" wide and not 4" tall- would limit the strength of the overall lift?
@creative Channel Please sir, I am a mechanical engineering student and my final year project topic is related to what you just produced.
Please can you give me the contact address or phone contact of where you got the hydraulic lift from?
It is very urgent sir.. Thanks in advance
brilliant imagination , bet your feet spark burns
Great work I was wondering if you send me the plans so I could make one
how many psi is the pump dynamo bro?
Cuánto dura su batería y cuanto tarda en cargar ?
Hi, Do you sell this forklift ? If yes please dm me.
Do you have circuit design and cad design of this machine?
Do you sell this project? I mean, all drawings, specifications?
good work man , but you can add wireless controller i think is better , in futuer you can also add wheel controller .
No tiene medidas ? Me gustaría intentar hacer uno . Como se dice ...
I Need a kind of blue print.
I ll try to make one .
Cara fez no olhometro...kkk
Hi there! Where to find and buy the hydraulic electric pump? Thanks!
For next project can you please make electrical engine forklift