Lyndon, your approach to videos/teaching is excellent. You have a very humble and jovial approach and the pacing / details are perfect. I'm also in Florida and building a larger version of a tracked-Ardurover with RTK GNSS for centimeter accuracy. If you'd like, I'll drive it up to you and you can do a video on it :) One other video suggestion: your 3D printer looks interesting. Perhaps a video on your build would interest some of your viewers?
Good afternoon. Can I connect the two servo motors for the sweep control and the saber tooth 12a to the Pixhawk 2.4.8 auto-pilot control using the dots?
Hola Lyndon !. Estoy pensando en comprar un kit con el pixhawk 2.4.8 crees me puede servir para mi robot terrestre o debo comprar una version mas moderna ?.
Hi. It is an old mobius camera I have connected to a 5.8ghz standard video transmitter. On the receiver end is just a standard 5.8 ghz video receiver from my groundcontrol station build video. Pretty basic fpv video setup.
How accurate is this gps setup for a lawn mower build? Is it able to follow a path reliably ? Would you need to buy the Pixhawk Orange Cube plus for the best result ?
Hi. I never owned an orange cube but based on my understanding and experience of gps guided drones, their accuracy is about of a few feet, depending on the number of satellites received. You can observe it during rtl. It never goes back on the exact spot. You need to at least supplement it with a vision system to guide your vehicle to exact path.
Thank you very much for the video! I am facing one problem when using this. When I center the throttle like in 7:07 , the backward doesn't work well. when I try to go back sometimes it go back and most of the time it doesn't. Also when it does go backward, I have to first center the stick then very slowly go back (Does not work if I move the stick from forward to backward in one swing). Can you tell me what's happening and how to solve this issue?
@@user-wj8li4fe2c The motor drivers I’m using are for dc motors. They are capable of reversing the polarity going to dc motors making them turn the opposite direction. You are not using ESC for brushless motors (drone motors) are you? If you are, I’m not familiar of any capable of reversing.
@@LyndonsWorkshopThanks for the reply. Could you give me the model name/item name of the motor controller? Can I use a Esc driver for dc motor. This is pwm control. Thanks in advance
@@surflaweb Hi. I’m using a SyRen motor controller. Choose an amperage higher than your motor current draw. As for the esc, I don’t think you can use an esc (the ones used on quadcopters) as it is for 3 phased winding inside the brushless motor. While brushed dc motors only have 2 wires.
@@surflaweb Hi. I did a quick look on l298n motor controller. It seems to need a pwm to control the speed and separate signal to control the direction. I don’t think its compatible with pixhawk. As pixhawk only sends pwm to control both speed and direction.
Thank you for great video sir👏 I'm currently doing my college Mini project on this ardupilot rower , our project in initial stage... For implement the (Autonomous Lawn mower).. I need a Guidence for me sir ... I have no Idea to where buy the requirements... requesting to guide me sir
Hi Hariharan. I lived here in the US. I bought these parts either in amazon or the local hardware store. For Autonomous Lawn mower. I don't advise you use the tracked rover as they work on skid steering. That means they need to skid just to turn. This is difficult on grassy surface and you need to have very powerful motors and mechanical parts to do this. You will be better off using the separate thrust and steering method like the ones they use on electric wheelchair. If you could afford to purchase those used ones the better.
Please, share me a cost estimation for what's you done in above video. Please share me a link to be the full setup requirement to buy ... Your kind reply.. helps me to achieve my major project for academic
Hello Lyndon's Workshop !. Can my robot be made autonomous only with the RTK GPS with Pixhawk without Arduino? My robot uses the MDDS30A FlySky FS iA6X transmitter with FS iA10B receiver connected to the Cytron controller and I would like to make it autonomous like your robot Is it also necessary to buy the Arduino? Please help me with my project, advise me, I am very new to this, watch my 2 videos, my robot and see what you think!
Hi, you don’t need an arduino to perform autonomous missions. Pixhawk is capable of saving and running missions on its own. Watched your video and saw your build. Pretty cool. I may use cytron controller also in the future. Thank you for sharing.
Thank you for helping me with my doubts, I built it to help my father in the field since I broke my back, I am a professional driver and due to my injury they cannot operate on me and it is over for my international truck trailer trip I hope when you make more things I can see them and if you see I can improve mine even more I will be happy I wanted to make it prettier but I don't solder and the drawing on paper to do it physically changes everything a lot I wanted to make a body that stands up like a hood so it looks like a truck With the Tesla one I wanted to do something like that but I don't understand nor do I have any practice with fiber or polyester resin. For me this is now economically impossible for me but hey at least I don't lose the hope of doing good things to entertain myself while!@@LyndonsWorkshop
Hi user-fv9hc6py2o. I didn't test how much load it can accommodate. Depending on your application, you can replace it with more powerful drill motors. I am only using 12v drill motors with 10A motor drivers. This build was just a proof of concept and meant for demo in a science project setting. Do you have a particular load in mind?
Maximum load 500-600 kg. 100-150 kg the frame and the main construction and other will be an external load. Is this pixhawk board capable of working bigger loads if we increase the power of the electric motors in watt?
@@user-fv9hc6py2o this setup definitely cannot accommodate that amount of load. I was initially thinking of recommending you the electric wheelchair setup as the mechanical design and motors already designed for heavy load but that one also is not enough for your requirement. The pixhawk microcontroller will output pwm signal to control the motors. It is the motor drivers and the motors you should change to accommodate your load.
Lyndon, your approach to videos/teaching is excellent. You have a very humble and jovial approach and the pacing / details are perfect.
I'm also in Florida and building a larger version of a tracked-Ardurover with RTK GNSS for centimeter accuracy. If you'd like, I'll drive it up to you and you can do a video on it :)
One other video suggestion: your 3D printer looks interesting. Perhaps a video on your build would interest some of your viewers?
Thanks for the great crawler and video!
I'll use it as a reference for setting up my ArduPilot rover.
Thank you and thank you for watching.
Nice build! I really like the color scheme.
Thank you
This is amazing! Adding the Pixhawk Autopilot to the Ardurover Build is definitely taking it to the next level! 🚀
Thank you!
are you high?
awesome!
Hi sir what equipment are you used
next step is to make turrent and make dual stabizer ?
Good afternoon. Can I connect the two servo motors for the sweep control and the saber tooth 12a to the Pixhawk 2.4.8 auto-pilot control using the dots?
Como esta se puede conectar por cable o toca hacer algúna modificacion
You got that submarine controller 💀💀
I saw the sub company’s documentary and noticed the extension on their gamepad and copied it. 😁
Hola Lyndon !. Estoy pensando en comprar un kit con el pixhawk 2.4.8 crees me puede servir para mi robot terrestre o debo comprar una version mas moderna ?.
Pregunta se puede conectar por cable.. Para controlarlo...
hello sir, do you know how to input rtk gps inject on pixhawk?
How are your cameras connected? What equipment to use?
Hi. It is an old mobius camera I have connected to a 5.8ghz standard video transmitter. On the receiver end is just a standard 5.8 ghz video receiver from my groundcontrol station build video. Pretty basic fpv video setup.
How accurate is this gps setup for a lawn mower build? Is it able to follow a path reliably ? Would you need to buy the Pixhawk Orange Cube plus for the best result ?
Hi. I never owned an orange cube but based on my understanding and experience of gps guided drones, their accuracy is about of a few feet, depending on the number of satellites received. You can observe it during rtl. It never goes back on the exact spot. You need to at least supplement it with a vision system to guide your vehicle to exact path.
Thank you very much for the video!
I am facing one problem when using this. When I center the throttle like in 7:07 , the backward doesn't work well. when I try to go back sometimes it go back and most of the time it doesn't. Also when it does go backward, I have to first center the stick then very slowly go back (Does not work if I move the stick from forward to backward in one swing).
Can you tell me what's happening and how to solve this issue?
May I know what motor driver you are using?
I am using two ESCs.
@@user-wj8li4fe2c The motor drivers I’m using are for dc motors. They are capable of reversing the polarity going to dc motors making them turn the opposite direction. You are not using ESC for brushless motors (drone motors) are you? If you are, I’m not familiar of any capable of reversing.
Hi sir, Can you say which motor driver you use?
SyRen 10A. It's already obsolete. You can replace it with newer versions and higher amperage. Thank you for watching
which ppm encoder are you using?
I bought one and I don't think it works. I am pretty sure I wired it correctly
thanks in advance
Update: i wasnt able to get my ppm encoder working, but I was able to get it working with a different reciever that just supported sbus 🤷♂️
Y el video en directo como es
With this configuration you can do autonomous missions?
Yes. Unfortunately I don’t have a safe place to test missions as cars pass by the area every few minutes.
@@LyndonsWorkshopThanks for the reply. Could you give me the model name/item name of the motor controller? Can I use a Esc driver for dc motor. This is pwm control. Thanks in advance
@@surflaweb Hi. I’m using a SyRen motor controller. Choose an amperage higher than your motor current draw. As for the esc, I don’t think you can use an esc (the ones used on quadcopters) as it is for 3 phased winding inside the brushless motor. While brushed dc motors only have 2 wires.
@@LyndonsWorkshop ok I see that this is currently discontinued, for small dc motors can I use a l298n driver?
@@surflaweb Hi. I did a quick look on l298n motor controller. It seems to need a pwm to control the speed and separate signal to control the direction. I don’t think its compatible with pixhawk. As pixhawk only sends pwm to control both speed and direction.
Hey, It has been long since you have uploaded anything. What's wrong? everything okey?
can you give me component detail
Thank you for great video sir👏
I'm currently doing my college Mini project on this ardupilot rower , our project in initial stage... For implement the (Autonomous Lawn mower)..
I need a Guidence for me sir ...
I have no Idea to where buy the requirements... requesting to guide me sir
Hi Hariharan. I lived here in the US. I bought these parts either in amazon or the local hardware store. For Autonomous Lawn mower. I don't advise you use the tracked rover as they work on skid steering. That means they need to skid just to turn. This is difficult on grassy surface and you need to have very powerful motors and mechanical parts to do this. You will be better off using the separate thrust and steering method like the ones they use on electric wheelchair. If you could afford to purchase those used ones the better.
Thank you sir..now I have improvement in idea
Without flysky remote control ,is the possible to drive rover in auto mode by using mission planner..
Please, share me a cost estimation for what's you done in above video.
Please share me a link to be the full setup requirement to buy ...
Your kind reply.. helps me to achieve my major project for academic
@@Hariharan.K.03 yes. As you can see in the video, I’m not using an rc radio. I’m only using the telemetry radio and the mission planner.
Yes sir... i review that you using with mission planner
Thank you sir...
Hello Lyndon's Workshop !.
Can my robot be made autonomous only with the RTK GPS with Pixhawk without Arduino?
My robot uses the MDDS30A FlySky FS iA6X transmitter with FS iA10B receiver connected to the Cytron controller and I would like to make it autonomous like your robot
Is it also necessary to buy the Arduino? Please help me with my project, advise me, I am very new to this, watch my 2 videos, my robot and see what you think!
Hi, you don’t need an arduino to perform autonomous missions. Pixhawk is capable of saving and running missions on its own. Watched your video and saw your build. Pretty cool. I may use cytron controller also in the future. Thank you for sharing.
Thank you for helping me with my doubts, I built it to help my father in the field since I broke my back, I am a professional driver and due to my injury they cannot operate on me and it is over for my international truck trailer trip
I hope when you make more things I can see them and if you see I can improve mine even more I will be happy I wanted to make it prettier but I don't solder and the drawing on paper to do it physically changes everything a lot I wanted to make a body that stands up like a hood so it looks like a truck With the Tesla one I wanted to do something like that but I don't understand nor do I have any practice with fiber or polyester resin. For me this is now economically impossible for me but hey at least I don't lose the hope of doing good things to entertain myself while!@@LyndonsWorkshop
how much load do you think these motors and the electonic parts afford? except from the structure that is from wood and plastic.
Hi user-fv9hc6py2o. I didn't test how much load it can accommodate. Depending on your application, you can replace it with more powerful drill motors. I am only using 12v drill motors with 10A motor drivers. This build was just a proof of concept and meant for demo in a science project setting. Do you have a particular load in mind?
Maximum load 500-600 kg. 100-150 kg the frame and the main construction and other will be an external load. Is this pixhawk board capable of working bigger loads if we increase the power of the electric motors in watt?
@@user-fv9hc6py2o this setup definitely cannot accommodate that amount of load. I was initially thinking of recommending you the electric wheelchair setup as the mechanical design and motors already designed for heavy load but that one also is not enough for your requirement. The pixhawk microcontroller will output pwm signal to control the motors. It is the motor drivers and the motors you should change to accommodate your load.
Thank you very much for you immediate and very helpful answers! Thank you also for your very interesting video’s!!
You can to make a drone with this microcontrolleur
Thank you for watching. Yes, ardurover is a ground drone. I use pixhawk in my other videos for quadcopter as well.
Bro liked your video . But can you make a rover with a small budget yet fully functional
I don't know how to program code.
You don’t have to program ardurover. Just install the firmware and play with some settings. It’s easy once you know how.
lol velleman 3D printer!
Omg. That music is SO bad. Could hardly understand the words over music.