Sheet Metal Tutorial | Engine cover design in Creo Parametric
HTML-код
- Опубликовано: 14 дек 2019
- Lets design sheet metal part in Creo Parametric
The basic sheet metal design
• Sheet metal tutorials ...
Unbend Sheet metal
• Sheet metal Unbend in ...
Mapkes in Creo Parametric
• Create mapkeys, Nested...
good job! love your videoes!
Great job!
Useful one
Hello sir please share link for punch and notch command in surfacing
Mera bend back command fail ho rha hai… kya karu
great one sir...
Aapki wjh s m design engineer ban pai. Pahle degree thi sirf.
I get a lot of inspiration from your videos Create a video like this
though i had followed each step exactly shown in video whenever i am trying to unbent it shows me error as
"Highlighted swept flange walls cannot be unbent.
Recommended actions:
Redefine flange wall section or trajectory." can you please guide.
Try to reduce the flange height and check
same issue
Try to modify the dimension of the flange
Hi sir, great explanation. can you share the those drawing pdf for practicing ?
You can take a snapshot in hd resolution from the video.
I'm using Creo 5.0 and Creo can't unbend the design. Is there a problem with me? or maybe the version?
By the way it's really inspirational video. Thanks for that.
Sorry, problem is on me. The measures are inch not mm, i figure it later.
Hello, I am following this tutorial but the "Unbend" function fails in the regeneration... Any hints for that??
Try to increase the part accuracy.
@@CADxTraining the only difference I see is that, when I make the flange, i have to select one by one all the edges, while I saw that you do all in one time. Can be this the cause of failed regeneration? just in case, can u explain how do you select all edges in one time? thanks
@@mechlown right click the edge and then left click
Why did you took 30 degree taper angle while it is given as 120 degree
It's 30 degree one side and 120 degree other side. You can go with any angle depending upon your side.
@@CADxTraining ok
Make a video copy Geometry and Public Geometry plz
AFTER DIVIDING I CANNOT MAKE THAT AS START POINT WHEN I CLICK ON RIGHT CLICK THE COMMAND WINDOW IS NOT APPEARING
need to long press of right click
@@adityakshirsagar6059good luck for your future
Excellent video #siemenscadsolutions
there is unbending problem what to do?
Try to increase the accuracy. Go to "File-prepare-model properties-accuracy" and increase the accuracy. Change the value to 0.0001 that's it.
@@CADxTraining THANKS IT WORKED
unbent is not happening, it is showing error. after modifying the flange dimensions also i am getting the same error.
Increase the part accuracy
@@CADxTraining I made it 4 times Bro, but still I'll work on it.
Change the part accuracy
Dear sir in Creo 3.0 this section in not unbend plz give the solution
Move the flange outside the edge.
@@CADxTraining still not unbend in this also it shows error
Highlighted swept flange walls cannot be unbent.
Recommended actions:
Redefine flange wall section or trajectory.
Try to increase the accuracy. Go to "File-prepare-model properties-accuracy" and increase the accuracy. Change the value to 0.0001 that's it.
@@CADxTraining itS done thanks
Good to hear.
Unbend is not working at 8.33
Increase the file accuracy. It will work.
ruclips.net/video/h8cFpa67nFI/видео.html
@@CADxTraining Thank you so much. Its worked. I tried multiple times but I failed. Thanks for this support & your video is very informative.
Why i cant use bend back?
If you are getting any error then try to increase the file accuracy.
"Feature failed to regenerate" always show me this
Highlighted surface cannot be bent back.
Highlighted swept flange walls cannot be bent back.
This two messages also
Increase the file accuracy and try
I tried that too, but everything is the same again
Sir drawing is not visible
Play the video at 1080p