I have a 2001 Sebring 4dr Sedan. No screw in the top rear corner. Very difficult to pull the panel off the retainers, in the rear, the others came loose, easily, but there is a stud on the sheet metal, with a large flat head, about the size of a Nickle, that keys into a plastic retainer, like a button hole, with the top of the slot open. Looks like you need to move the panel down as you hold the top of the panel from over the frame. The large flanged stud stays on the frame and the button hole clip is fastened onto the panel. When you removed the panel, I could see the sheet metal where the insulator sheet has a cutout to fit around a round raised "bump" in the sheet metal; but I could not see the large, flat, flanged stud. There are other videos illustrating this task for model years through 2006, they don't apply to the 2001, yours does except for the 6th screw and the stud that is really difficult to pull through, I expect that it would possible break off, since part of it is rubber. But, I did get it off and without breaking anything. Thank you, nice job.
Just giving you a heads up, the video was a good starter to some of the screws. However, on the 2001 model, there are additional screws. I had to remove the speaker panel and pull off three screws from there. Just up from the speaker is another panel to remove with an additional screw in there. The reflective plastic piece on the lower left has one behind it. And there are two more screws behind the door panel that I haven't figured out how to get to yet. Again good video, very helpful in starting, just wanted to give you a heads up.
David Larson. OMG you are such a LIFE saver!!! I have an 01 model n i took all the visible screws out but the door still wouldn't pop that like he is did. And then I screw it down and saw your post and I see why it never popped out because there are additional screws. Thank you so much!
We currently do not have an auto repair video specific to your vehicle. You might be able to apply some of the basic steps shown in this video to your application. +Mike VV
We currently do not have an auto repair video on that particular year. We have this video on the 2006. You might be able to apply some of the basic steps that need to be taken on your 2007. Hope this helps you out. How To Remove Install Rear Door Panel 2001-06 Chrysler Sebring
After I posted, I read the post below, David Larson commented that he had to remove the speaker cover on his 2001, My speaker cover isn't removable, that is why I commented about the differences on my 2001. I don't know why David's 2001 is different than mine, except I purchased my 2001 in the fall of 2000, and the convertible is a different car than the sedan.
Be careful on the 2006 Sebring convertible. There is a panel on the door near the inner hinges that houses a screw into the door. I accidentally pulled on the panel and broke the screws thread backing support. So, pop the panel off first & unscrew this screw first. To fix I had to use a longer screw with a washer for support!
Thanks for the great video. My 2005 is a little different, so maybe this will help someone with a 2005: I followed your video, except I don't have a screw on the vertical edge of the door panel by the latch. Then I found three more screws under the speaker grill (The grill snaps off. I think I pulled from the bottom of the grill.) and another screw under a sort of rounded tip triangle shaped plastic panel between the door handle (the part you pull to open the door) and the hinge edge of the door panel. It looks like it's just part of the door panel. Pull that rounded tip triangle panel off, starting from the edge closest to the door handle, then take out the screw. I didn't take the whole door panel off because I just needed to reach behind the speaker to slip a new door catch strap in, so I'm not sure if there are more fasteners to remove to get the whole panel off.
+charles dunaway We don't have a how-to video for your vehicle right now, but the basic steps in this video should be enough to do this task. Buy this part for your vehicle on 1AAuto.com: 1aau.to/m/Shop-1AAuto-c
hi, I have a 2004 chyrsler sebring convertible. the door rattles , drivers side,when the window is up but not when I have the window down. can you show me what I need to do besides take off the door panel. is it maybe a broken clip of some kind?
+Marti Brown We currently do not have an auto repair video for this particular repair. We'll keep this request in mind in the event that we need to make this repair in the future. 1aauto.com
Glad to see the "re-designed" the driver/passenger door panel for the 2001 thru 2006 sebrings. The ones on a 1998 Chrysler Sebring JXi are garbage. Actual metal screws along the bottom of the door panel... what an engineering master-stroke of genius. They are just like door panels on my 84 El Camino... imagine that. Whoever decided to have all those plastic/nylon inserts instead of screws to attach the panel to the door frame... should have every one of them shoved up his butt.
Getting that triangle piece back in on the 2000 convertible....is nearly impossible because the door panel and triangle piece totally interfere with one another, requiring immense force to bend the plastic piece down behind the door panel as not to damage the vinyl.
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto
√ *Do it Yourself*
√ *Save Money*
I have a 2001 Sebring 4dr Sedan. No screw in the top rear corner. Very difficult to pull the panel off the retainers, in the rear, the others came loose, easily, but there is a stud on the sheet metal, with a large flat head, about the size of a Nickle, that keys into a plastic retainer, like a button hole, with the top of the slot open. Looks like you need to move the panel down as you hold the top of the panel from over the frame. The large flanged stud stays on the frame and the button hole clip is fastened onto the panel. When you removed the panel, I could see the sheet metal where the insulator sheet has a cutout to fit around a round raised "bump" in the sheet metal; but I could not see the large, flat, flanged stud. There are other videos illustrating this task for model years through 2006, they don't apply to the 2001, yours does except for the 6th screw and the stud that is really difficult to pull through, I expect that it would possible break off, since part of it is rubber. But, I did get it off and without breaking anything. Thank you, nice job.
Just giving you a heads up, the video was a good starter to some of the screws. However, on the 2001 model, there are additional screws. I had to remove the speaker panel and pull off three screws from there. Just up from the speaker is another panel to remove with an additional screw in there. The reflective plastic piece on the lower left has one behind it. And there are two more screws behind the door panel that I haven't figured out how to get to yet. Again good video, very helpful in starting, just wanted to give you a heads up.
David Larson. OMG you are such a LIFE saver!!! I have an 01 model n i took all the visible screws out but the door still wouldn't pop that like he is did. And then I screw it down and saw your post and I see why it never popped out because there are additional screws. Thank you so much!
Miten irroutetaan lasinnostin paneeli??
+matti lähtevänoja Great question! Check out our library for more videos here: 1aau.to/m/video-library-c
I was looking for this for our Sebring Convertible... very similar to the hard-top... very insightful video... Thank You for sharing!
We currently do not have an auto repair video specific to your vehicle. You might be able to apply some of the basic steps shown in this video to your application. +Mike VV
Very good video Don - I am wondering if you could tell me how to remove the rear door hardware on a 2007 Sebring 4 door? Thanks!
We currently do not have an auto repair video on that particular year. We have this video on the 2006. You might be able to apply some of the basic steps that need to be taken on your 2007. Hope this helps you out. How To Remove Install Rear Door Panel 2001-06 Chrysler Sebring
After I posted, I read the post below, David Larson commented that he had to remove the speaker cover on his 2001, My speaker cover isn't removable, that is why I commented about the differences on my 2001. I don't know why David's 2001 is different than mine, except I purchased my 2001 in the fall of 2000, and the convertible is a different car than the sedan.
Be careful on the 2006 Sebring convertible. There is a panel on the door near the inner hinges that houses a screw into the door. I accidentally pulled on the panel and broke the screws thread backing support. So, pop the panel off first & unscrew this screw first. To fix I had to use a longer screw with a washer for support!
Marc Zampella thank you bud
@@pandaabadu 😊😊0😊
Thanks for the great video. My 2005 is a little different, so maybe this will help someone with a 2005:
I followed your video, except I don't have a screw on the vertical edge of the door panel by the latch. Then I found three more screws under the speaker grill (The grill snaps off. I think I pulled from the bottom of the grill.) and another screw under a sort of rounded tip triangle shaped plastic panel between the door handle (the part you pull to open the door) and the hinge edge of the door panel. It looks like it's just part of the door panel. Pull that rounded tip triangle panel off, starting from the edge closest to the door handle, then take out the screw. I didn't take the whole door panel off because I just needed to reach behind the speaker to slip a new door catch strap in, so I'm not sure if there are more fasteners to remove to get the whole panel off.
would it be about the same for an 09 sebring? My driver side window won't come back up but I can here the motor.
+charles dunaway We don't have a how-to video for your vehicle right now, but the basic steps in this video should be enough to do this task. Buy this part for your vehicle on 1AAuto.com: 1aau.to/m/Shop-1AAuto-c
GOOD SHOW
hi, I have a 2004 chyrsler sebring convertible. the door rattles , drivers side,when the window is up but not when I have the window down. can you show me what I need to do besides take off the door panel. is it maybe a broken clip of some kind?
+Marti Brown We currently do not have an auto repair video for this particular repair. We'll keep this request in mind in the event that we need to make this repair in the future. 1aauto.com
You should make a video on how to remove the door completely. Those wire harnesses are a pain
+Phil Murphy We do not have a video for this repair right now, but we'll keep this request in mind for a future video! 1aau.to/m/Shop-1AAuto-c
Glad to see the "re-designed" the driver/passenger door panel for the 2001 thru 2006 sebrings. The ones on a 1998 Chrysler Sebring JXi are garbage. Actual metal screws along the bottom of the door panel... what an engineering master-stroke of genius. They are just like door panels on my 84 El Camino... imagine that. Whoever decided to have all those plastic/nylon inserts instead of screws to attach the panel to the door frame... should have every one of them shoved up his butt.
Getting that triangle piece back in on the 2000 convertible....is nearly impossible because the door panel and triangle piece totally interfere with one another, requiring immense force to bend the plastic piece down behind the door panel as not to damage the vinyl.
what about a 98 chrysler sebring
+James Truth It may be a different procedure on that vehicle.
Ha That is the exact car I need to work on
@nayte1 Thanks for watching. 1aauto.com 888-844-3393