Did you use the longest hook joint in the abdomen section, mine also kept falling off because the chest cover pinches against the abdominal section which prevents a lot of back and forward motion, so it does tend to pop off that's if you move it too much over a certain point. So you have to move the hip section if you want a more bent pose.
@@HasnaRimi Did you put it on the right way? Try straighten the leg and gently press against a table to connect the knee cap to the leg, there should be a small protruding piece that it clips onto.
It doesn't matter which way because they both the same length 😂 but you want the side with the point in the middle facing towards the back, so you can add the neck cover onto it.
I also got a black one but I first put all of them apart for the jointment of 3d print than I closely looked at all the peoces and focused alot. Took me like 1-2 hours to build
Yes, it's not easy if you get a knock off like mine, the joints are rigid and not very smooth to slide in each other. They can get stiff and sticky, you might need a little force to combined them but be careful not to push to hard on the small edges because they can break, like I did to mine. I super glued that piece that broke and its not noticeable unless I actually point it out😂
Make sure the shoulder hook joint is connected in the right position, it should be attached to the ball joint horizontally, I think that could be the problem.
Try use small tweezers fit the joint inside the head, then push down using the back end of the tweezers. It should fit in nicely unless your figure isn't well made, like mine.
@@saffy630 make sure everything facing the right way, you want the m shape to face the back of the leg so the middle part of the m is facing the front for the knee cap.
Yeah you got to push against a table or something, like I did with the back of my piliers but also not to break it at the same time xD. Make sure the 3 is facing the right way, you want the mid of the 3 facing outward so you can connect the knee covering to it later.
Mine was big too. I had to heat it up a little and squeeze it a bit with pliers but not too much else you might break it. Then I pressed down against my table and it eventually popped in place.
You must slide the cover over the joint from the smaller side (joint section) not the hook part because its too large to get it over. If you unsure which way the cover must face, the colour parts of the cover must face the top and bottom, when you lay the black hook joint flat on the table. I hope my explanation made some sense.🙈
@@Olliebolly987 I never boughr one from Amazon but they look overpriced xD, I got mine from Temu at a very low price, it was like R25, that's like $1.34
Yes it doesn't line up nicely with the back holes but try dipping it in lukewarm water(not boiling water) and then gently attaching the yellow to the black skeletal part, it wont completely fit perfectly but it will still function and fit better than before.
mmm that's strange but it generally doesn't clip in nicely either, try rotating the joints 180 and clip the hip covering on again so... maybe the one side doesn't clip properly to the other side.
Yeh got to apply some pressure so it can click in, like against a table or dip the covering part in some lukewarm water and gentle push it in. It was difficult to put the legs together because of the cheap one I got.
I don't know what you mean by under 😅the hip part and leg section? Probably because the joints are wrong sizes with the limbs, normally happens with cheap ones.
Damn..I guess Temu is more trustworthy than the TikTok shop.🙈 Isn't there a way of getting a refund? I've never bought from the TikTok shop before but thanks for the heads up.
Yes but Lego is made differently, you should give it a try. It's mainly trying to connect the pieces that don't fit nicely together, which is the main problem in this figure.
Try connecting the black joint first inside the head then attaching it to the neck. Use a pencil tip or something small to push the joint into the head to make it easier.
Click to which? The chest or to the hips? It's bad, mine didnt fit properly either.. Did you have the longest ball hook joint in the mid section. Try put the chest part in warm water for a little while and then try click it in, but be gentle.
I cant connect the chest to the mid part it keeps falling off
Did you use the longest hook joint in the abdomen section, mine also kept falling off because the chest cover pinches against the abdominal section which prevents a lot of back and forward motion, so it does tend to pop off that's if you move it too much over a certain point. So you have to move the hip section if you want a more bent pose.
me too
Some come defective. I bought 2 so far and the first one came without a thigh bone and a short hook joint. That's why it pops off.
Me too
Me to
Yo i have a problem with the knee part what do i do
Are you talking about the knee cap?
@@J.KINGTOONZ ye and the shoulder cap it doesnt fit allat
@@HasnaRimi Did you put it on the right way? Try straighten the leg and gently press against a table to connect the knee cap to the leg, there should be a small protruding piece that it clips onto.
@@J.KINGTOONZthe knee part fitted in, Thanks!
2:55 the ribcage on mine has a hole but the rib doesnt, what do i do
The holes at the back doesn't matter, it won't affect the figures function. I think it was just a design to show the front and back of the piece.
Maybe, can you do another video?😅 and show the people what pieces to get exactly.😅😅 please
ruclips.net/video/Q97jp2NGWa4/видео.html That's my other video that shows all the parts.
my hands cant move and they break easily also the same with the legs and tip?
just try to make them move then there will be a crack sound
@@beambastic3711 k ty
Which way do I put on the neck piece it’s hard wondering how I put it on
It doesn't matter which way because they both the same length 😂 but you want the side with the point in the middle facing towards the back, so you can add the neck cover onto it.
@@J.KINGTOONZok tysm I just finished it this video is amazing you deserve a like and sub
@@Squ3aky-YT Thanks man, I appreciate the support ❤️
@@J.KINGTOONZthis vid is so helpful I already finished 4
@@Squ3aky-YT wow you got 4, you should try make a stop motion with them👌
On the part above the waist the thing that goes inside of there won’t go in 2:07
The ab part? You putting it in the right way round? Else you got to put the colour part in warm water for a bit and try connecting the black part.
I cant connect the head to the neck the other took me so many hours the thing you put inside of the head i cant connect it with the head
When working with ghe crotch i can't connect it when it looks like i did its not all the way up and i 3d printed one
When you connect it to the torso?
I y do some of the prices keep sliding off when I attach them
Maybe they too loose and need to be more rigid, try adding a small layer of super glue around the ball joint.
What is the name of the scissors tho
Haha it's just really sharp kitchen scissors that I had, I don't know the name. Sorry 🙈
I had to throwaway my first one and buy another one lol 😂
Same because it was to hard to assemble
Bro you're trash at teaching
I GOT THE BLACK ONE 😢😢😢😢 I CANT FIND THE JOINTS 😭😭😭😭
I see what you did there😂 I hope you find them😅🙏
Lol.
I also got a black one but I first put all of them apart for the jointment of 3d print than I closely looked at all the peoces and focused alot. Took me like 1-2 hours to build
@@sumreenabdullah4929 @Guesty_AnimationsOfficial joke was funnier.
I placed the three things wrong how to put it on the right side?
The point must face you for the knee cap.
I had so many problems of mine i had to throw some peices just to connect a joint
😂 I feel the frustration
Same bro it was so hard for me to put the arms on practically threw it
@@jordanchristopher3244 😱 I hope its okay now😂
This is almost as bad as Lego
How to assemble the stand
THX IT WORKS SOO WELL
@@Breadcatlol69 I'm glad you got yours together 💪
thanks it really helped 👍
I'm glad it helped💪
Am having trouble connecting the first one
Yes, it's not easy if you get a knock off like mine, the joints are rigid and not very smooth to slide in each other. They can get stiff and sticky, you might need a little force to combined them but be careful not to push to hard on the small edges because they can break, like I did to mine. I super glued that piece that broke and its not noticeable unless I actually point it out😂
It took me days to assemble like im still working on it😂😂😂😂
@@danielapociumbeanu3406 Damn..that's crazy 😂 but you will eventually get there XD.
I hope 🤣
Me too
Thank you so much. This really helped me.😄
@@Raptor_Tamer You're welcome😉
Bro the arm for me doesn’t move it’s stiff idk why it won’t move up and only down
Make sure the shoulder hook joint is connected in the right position, it should be attached to the ball joint horizontally, I think that could be the problem.
I can't connect the head with the joint
Try use small tweezers fit the joint inside the head, then push down using the back end of the tweezers. It should fit in nicely unless your figure isn't well made, like mine.
@@J.KINGTOONZ ty
@@J.KINGTOONZ where you buy you figure I wanna buy other
@@NiyazQi from Temu😂
the m shape isnt fitting in the leg?
@@saffy630 make sure everything facing the right way, you want the m shape to face the back of the leg so the middle part of the m is facing the front for the knee cap.
this video helped me alot i had to make 3
Damn 3, that must of taken long to connect all those parts together 💀
Oh yea I have 6 bro 😂💀
!! I just need the legs and hands but you got my other piece together !! I’ll be back tomorrow lol
@@yazminvilla1835 Haha, hopefully the video somewhat helped 😅🙈
4:52
Bro the number 3 looking attachment is not budging to the leg
Yeah you got to push against a table or something, like I did with the back of my piliers but also not to break it at the same time xD. Make sure the 3 is facing the right way, you want the mid of the 3 facing outward so you can connect the knee covering to it later.
@@J.KINGTOONZi placed the 3 wrong way xd
I need to connect all of them I mean all of the colors blue red everything
Nice! You have a variety of different ones, send me some haha
How to do the headd
Turn the black joint to the side and push it in and use a small tweezers to push it in firmly.
Thank u
You welcome
Mine was having a really big problem Like the body dont comnect or it doesn't fit through cus its too big
Mine was big too. I had to heat it up a little and squeeze it a bit with pliers but not too much else you might break it. Then I pressed down against my table and it eventually popped in place.
thx it helps me aot it works so well
@@Hollow_clust3 I'm glad you got it to work👍
Thanks
i don't get it on 15m 23s
You must slide the cover over the joint from the smaller side (joint section) not the hook part because its too large to get it over. If you unsure which way the cover must face, the colour parts of the cover must face the top and bottom, when you lay the black hook joint flat on the table. I hope my explanation made some sense.🙈
Thank you so much
@@Madikz0 You're welcome 😁
Why do they not send them assembled
Some do but you pay more haha and besides... you won't have the joy of assembling them yourself XDDD
Are the ones of Amazon good
@@Olliebolly987 I never boughr one from Amazon but they look overpriced xD, I got mine from Temu at a very low price, it was like R25, that's like $1.34
@@Olliebolly987 i bought a amazon one it broke easily if u want a amazon one u should buy it assembled
4:00 it won’t let me do it
Put it in hot water so it softens a little and then try connect it. The heat usually expands the clip joint.
Mine was too hard bcz the chest part doesn't fit 3:18
Yes it doesn't line up nicely with the back holes but try dipping it in lukewarm water(not boiling water) and then gently attaching the yellow to the black skeletal part, it wont completely fit perfectly but it will still function and fit better than before.
The headpart don't fits on mine
Does it keep popping off?
@@J.KINGTOONZ yes
i have to build 15 of them took me 2 hours to make
Damn that's fast!
The knee won’t connect
You gotta press hard sometimes, preferably against a desk.
My hip section is all busted and won’t clip in for anything
mmm that's strange but it generally doesn't clip in nicely either, try rotating the joints 180 and clip the hip covering on again so... maybe the one side doesn't clip properly to the other side.
You Have To The click
😊
🤔
bro the i cant put the crotch section to the chest
You must connect the abdomen section before connecting to chest.
Thanks, it help me out a lot.
I'm glad it helped someone😁
Ty!!!!!❤
@@sairnazari7446 Welcome 💪
Had to glue some of my dummy 13 cause some of the joints didnt want to connect, i also have a fake one
Yeh it's not as easy as some videos make it to believe 😂
Head can't connect please😢
Did you put in the head joint inside the head?🤔
for those whose having a hard time on the limbs do side on the letter Y and put it and just rotate it to the front again.
The leg is too hard to assemble it kep falin
Yeh got to apply some pressure so it can click in, like against a table or dip the covering part in some lukewarm water and gentle push it in. It was difficult to put the legs together because of the cheap one I got.
Damn really?
@@jhoorlino5330 yes hot water expand plastic and makes it softer to take apart and put together 👍
Really help the assembly guide was really confusing
I'm confused to what you said, did the guide confuse you?🙈
Now record one with focus on the parts ......
The arms cant move... It only goes straight instead of other directions
Did you put the joints the right way?
@@J.KINGTOONZI FIXED IT!!
@@demonvoid4746 That's good 👍
This helped me so much
I'm glad 👍
Same
3d printing them bigger and then assembeling them ist so much easier
True and less likely to break.
Yeah my first one was printed at 200%
I can't attach the middle part and the body
Is there not enough space for it to connect?
Jeez i got ming of temu and it was not easy
@@darlewis1759 haha same🙈
The under of the toy is still falling bro😢
I don't know what you mean by under 😅the hip part and leg section? Probably because the joints are wrong sizes with the limbs, normally happens with cheap ones.
@J.KINGTOONZ oh thanks for the help @J.KINGTOONZ
I HAVE THE SAME ONE
I DID IT!!
WAHOO! Gratz man🎉
Ty
The hard part is the head since it is hard to put in the lego like hand inside the square 😑😑😑
Fr
😂
I just ordered a lot of similar ones, so wish me luck
So hard to assemble
Just got scammed on the tiktok shop by this like bro I brought the same version dummy 13 and most of the pieces weren't even there
Damn..I guess Temu is more trustworthy than the TikTok shop.🙈 Isn't there a way of getting a refund? I've never bought from the TikTok shop before but thanks for the heads up.
I think it will be easy for me cause i'm a great builder of Lego🙃
Yes but Lego is made differently, you should give it a try. It's mainly trying to connect the pieces that don't fit nicely together, which is the main problem in this figure.
I MADE MY SECOND ONE :D 3 MORE TO GO
Thx bro
bro i used my hands to take off the parts before assembling it💀💀
Damn you got some strong fingers
For me the little parts are the most hardest part to put on probably going to take a other 3 hours
Goodluck! 🙏
The head is my problem
Try connecting the black joint first inside the head then attaching it to the neck. Use a pencil tip or something small to push the joint into the head to make it easier.
My son has broke her toy but he has a new one
Nice💪
I waited 7 months for this and it came with missing pieces I HATE THIS CRAP
@@Ryomen_Sukuna2935 Damn 7 months!! That's insane 😱, I got mine in 2 weeks😅
@@J.KINGTOONZ it came witgout 5 peices
Mine is 3 days@@Ryomen_Sukuna2935
Oh, and also I lost the knee piece on the concrete in a crack, but I’m glad that I have a gold one coming and I found the piece
So wait... its not in the crack anymore?🤣
No I found it
I just got a 3d printer now I don't got to buy these over priced things
bro my body middle center cant even click im crying rn cuz it’s supposed to be for my brother birthday
Click to which? The chest or to the hips? It's bad, mine didnt fit properly either.. Did you have the longest ball hook joint in the mid section. Try put the chest part in warm water for a little while and then try click it in, but be gentle.
The head id too hard to assemble it keeps falling
Same
5:08 how do you do this
Turn the black joint to the side and push it in and use a small tweezers to push it in firmly.
I cant find the long part i cant connect the abdominal 😢
I cant connect the three piece to both of the legs
Is it facing the right way? The point must face you so the knee cap can clip onto it.