@@SkinnersScreens1972 Don't understand how it is "easier" to install a window screen from inside the room. I am no DIY wonder, but it seems to me that it is impossible to use the same technique form inside the room, as the framing will simply get in the way of the screwdriver. Maybe I am wrong. But personally I am baffled on how to proceed. I don't have a ladder, and even if I did, I am nearly 70 years old, and don't fancy hanging off a sloped roof while trying to install this window screen. On the other hand, paying someone with worker's comp to do will probably set me back a minimum of $300 in California. I ain't kidding. So any advice?
But what do you do when you have to install a new window screen on a 2nd story and the slope of the roof is just steep enough to discourage me from going out on the roof? Yeah, I could hire someone with worker's comp and pay them several hundred dollars for a 10 minute job. That is way expensive for installing a $34 window screen. Is there anyway to install the same screen window from inside the room?
I need to build some replacement screen frames for my home, and the process seems pretty straightforward except for the bell clips. How do you recommend cutting the groove for the clip and inserting the clip into the frame? Unfortunately all of the video tutorials I've seen use other types of clips.
Great question Kurt. We have a special tool to cut the slot for clips. However, you can use a box cutter razor (be very careful of course) to cut the slit on back side of frame about 3/4 inch wide. Use a flat head screwdriver to widen the slit and insert the Bale Clips. You may also need a needlenose pliers
Great question. The best option is to have new screens custom fitted by your local expert; check reviews. Typically, window screens are designed with a little wiggle room so you may remove them without too much discord. Or, try using a strip of 5/16” weatherstripping with a sticky back to see if that helps. WHATEVER YOU DO, “DON’T CAULK THEM”. It sticks like glue!
Many windows are different. Perhaps you have tilt-sash windows; I don’t know. Have a local professional look at them. Happy trails and thanks for the commentary
Spline faces out, typically, unless you like to have the tabs on the outside for easy removal. Spline out for a more aesthetically pleasing look. Thanks for asking. If you don’t mind, share and subscrine
Jose, it’s called a “tack puller”. You can buy them at a local hardware store, Home Depot, Lowes, or online. They are quite handy. Cost is approximately $8.00. Find them in the screwdriver section
Хобби
Deserves way more than 315 subscribers. I subbed thank you.
Thank you. Share away. It’s only been 2 years.
That’s great unless your window is on the 3rd floor!
A great concern. We have ladders to get those
Easier from the inside anyway
We do it from outside because it saves us time unless required to install from inside. Great observation no doubt
@@SkinnersScreens1972 Don't understand how it is "easier" to install a window screen from inside the room. I am no DIY wonder, but it seems to me that it is impossible to use the same technique form inside the room, as the framing will simply get in the way of the screwdriver. Maybe I am wrong. But personally I am baffled on how to proceed. I don't have a ladder, and even if I did, I am nearly 70 years old, and don't fancy hanging off a sloped roof while trying to install this window screen. On the other hand, paying someone with worker's comp to do will probably set me back a minimum of $300 in California. I ain't kidding. So any advice?
@sgower414 that’s okay
But what do you do when you have to install a new window screen on a 2nd story and the slope of the roof is just steep enough to discourage me from going out on the roof? Yeah, I could hire someone with worker's comp and pay them several hundred dollars for a 10 minute job. That is way expensive for installing a $34 window screen. Is there anyway to install the same screen window from inside the room?
You may pop it in from the inside. It’s more convenient for us to do it from outside and not disturb the homeowner. Great question though
Thank you for Sharing 😊
My pleasure 😊
What if you dont have pull tabs on your window screen
Don’t need them. It’s a convenience.
Nice! Can you show us how to install a screen from the inside as well?
We’ll give it the “old college try”!
Will have one coming for you @lichelle51 with a shoutout
I need to build some replacement screen frames for my home, and the process seems pretty straightforward except for the bell clips. How do you recommend cutting the groove for the clip and inserting the clip into the frame? Unfortunately all of the video tutorials I've seen use other types of clips.
Great question Kurt. We have a special tool to cut the slot for clips. However, you can use a box cutter razor (be very careful of course) to cut the slit on back side of frame about 3/4 inch wide. Use a flat head screwdriver to widen the slit and insert the Bale Clips. You may also need a needlenose pliers
Please subscribe Kurt. Thank you very much
@@SkinnersScreens1972 Thanks!
Nice video! Do you have any recommendations for sealing screens on the sides? Mosquitoes are getting past my screens
Great question. The best option is to have new screens custom fitted by your local expert; check reviews. Typically, window screens are designed with a little wiggle room so you may remove them without too much discord. Or, try using a strip of 5/16” weatherstripping with a sticky back to see if that helps. WHATEVER YOU DO, “DON’T CAULK THEM”. It sticks like glue!
Thanks!
Ok, so what happens if the window is on the second floor and you can’t access from the outside?
Install from inside. Easy peasy
@@SkinnersScreens1972 not really. My windows have a lip that actually will make it harder from the outside
Many windows are different. Perhaps you have tilt-sash windows; I don’t know. Have a local professional look at them. Happy trails and thanks for the commentary
Long shot but what is that tool called you’re using??
Great question! It is called a “tack puller”. Has a crooked end on it and very handy as it provides a little leverage as needed,
so does the spline side goes inside or face the outside????
Spline faces out, typically, unless you like to have the tabs on the outside for easy removal. Spline out for a more aesthetically pleasing look. Thanks for asking. If you don’t mind, share and subscrine
Thanks 👍
You’re welcome. I appreciate your comment. Subscribe if you like
Thanks 🥃
Your welcome. Thanks for watching
These aren't the hard ones that have tracks all the way around and no clips.
Correct!
We don’t like those. They have special frames and we get as close as possible.
the hardest part of the job lord help me maybe my stupid house doesnt need window screens
Perhaps not. Many people don’t want them and that’s okay. We provide the service accordingly. Thanks for reaching out. Appreciate the commentary
@@SkinnersScreens1972 i ended up replaceing the metal frame window screen with one that had plastic corners. the plastic corners went in way easier
Fantastic
how to assemble that screen
I’ll do a screen assembly video. Thanks for commenting. Subscribe if you want
Like the tool. What is it called? Where can I get one?
Jose, it’s called a “tack puller”. You can buy them at a local hardware store, Home Depot, Lowes, or online. They are quite handy. Cost is approximately $8.00. Find them in the screwdriver section
@@SkinnersScreens1972 Thank you.
I've literally used a flat butter knife from the kitchen.
Well there you go. Whatever works. Tack Puller is your friend here
15th floor and from the inside
It’s doable