Me again, using Creo 7.0. Everything came out fine except the 90 degree dimension to open up the bracket. Every time I change it, I get an error and the Sketched Rip turn red on the design tree. I made sure to select all the correct References like you did.
Create without seam removes excess material which intersect the flat in first wall. but in Creo 5.0 i tried corner and bend relief no use. any other solution to solve
In this video you using the comment seam . Creo 4.0 there is not available seam comment or please tell me how to find the seam comment in this version .
How did you bring planes at 9:04 while mirroring. Is the any shortcut or is it a mapkey. If it is a mapkey what all are the steps you have recorded while recording the mapkey. Thank you.
@@CADxTraining your videos are helping me a lot in learning creo sheetmetal. you are one of the rare people with good content for creo on youtube. Thank you keep posting these.
@@CADxTraining I can't even give new dimension sir, it's not taking. When I click two lines , nothing happens. Is there any settings do I need to change?
Your channel is the best for learners
Thanks for your comment, it's valuable for me.
dear sir,
Please explain create without seam option how to open? at flat 1
it is special features of Creo 6.0?
I m using Creo 4.0
Regards,
dixit
Hi sir while changing the angle from 90 to 110 the surface becomes flat it is not moving as per your part.
Keep on sharing your knowledge
Me again, using Creo 7.0. Everything came out fine except the 90 degree dimension to open up the bracket. Every time I change it, I get an error and the Sketched Rip turn red on the design tree. I made sure to select all the correct References like you did.
Same here
+1
I also tried a lot but no use
Create without seam removes excess material which intersect the flat in first wall. but in Creo 5.0 i tried corner and bend relief no use. any other solution to solve
Great Lessons.
Are there any good sites where i can find more 2D drawings for practice
Not having much idea about any site.
If you really like the content, don't forget to hit the like, thankyou.
people trying to figure out how to use the option @ 8:45, extend the bend up to 0.02 on flat side it will result in the same way in the video
How i can do the creo 3.0
In this video you using the comment seam . Creo 4.0 there is not available seam comment or please tell me how to find the seam comment in this version .
You will get that option inside the bend relief or corner relief I guess in creo 4.
Nice
Hi sir i have one doubt in 8:04 min you are using create without seam option how to open that option in creo 4.0 please clarify that doubt. 🙏
Sorry to say that this is not possible in Creo 4. This option is available only in higher version.
@@CADxTraining What About Creo 5.0 sir Is there any option for that
You will get that after Creo6.
I m Using creo 5.0
video "8.05" comment creat without seam, you using popup
if any other option to remove the bend notch
It's not possible in creo 5
@@CADxTraining
Thanks for so much
You doing professional class and Vidio quality
Your speaking skills are Amazing
Doing good Bro
I found your channel
How did you change screen/view to normal at 12:36
I use a mapkey.
Hi I am using Creo 5.0 in part 8.08 while creating flange there is no option like create with out swept
This is the new function added in Creo 6. For earlier release of Creo, you need to cut the material to get this result.
SIR , HOW SHOULD WE SOLVE IT IN CREO 5.0
8.07 how to create without seam.
I am using creo 5.0
For lower version of creo parametric, offset the flange outside and adjust the related dimensions.
@@CADxTraining but how to adjust sir
How to drawing open in model tree
Done by video editor
How did you bring planes at 9:04 while mirroring. Is the any shortcut or is it a mapkey. If it is a mapkey what all are the steps you have recorded while recording the mapkey. Thank you.
You must watch this to understand.
ruclips.net/video/Hbazaf35MEs/видео.html
@@CADxTraining your videos are helping me a lot in learning creo sheetmetal. you are one of the rare people with good content for creo on youtube. Thank you keep posting these.
@@CADxTraining I was expecting that you may be using a mapkey. I am a fan of mapkeys/macros
@@CADxTraining You may need to tweak some options while uploading to catch more audience. like tags etc.
@@Steve-cm3by Thanks for the suggestion. I will take care of this.
8:45 how did you un seam that i cant get that tool bar sir.. pls help me
This is the new function added in Creo 6.
@@CADxTraining then in creo 5.0 its not working I'm correct?
@@CADxTraining and sir you activate that command by right clicking im right?
Yes
Sir, please tell me how can i use seam tool in creo 3.0?
I think, it is not there in 3.0
Is there other way to apply it?
I can't delete dimensions in creo , how do I do that ?
You can only delete the strong dimension in creo parametric. You can hide the weak dimensions.
@@CADxTraining I can't even give new dimension sir, it's not taking.
When I click two lines , nothing happens.
Is there any settings do I need to change?
Your "hide dimensions" is active. That's why dimensions are not visible.
@@CADxTraining how do I disable it ?
Inside the sketch - top left corner
Clickonce setup up and go to display then switch on dimensions display
How to bring that popup at 8:45
Which version of creo are you using? It is only available after Creo 5.
@@CADxTraining I'm using 5.0 but even after right click that popup won't show
It's a feature from creo 6.
Oh ok. Thanks. BTW your tutorials are amazing