Ok i repaired mine just by heating the cap with my iron for one minute. It was very hot so i believe everything inside as resoldered. It works now, no need for me to open !
Nice Job Sir...I have few question in my mind that i m using same Quick 2008 Model smd and try at 360c and 60 air to remove any glued ic but its took too much time and in few cases Motherboard pop up but i constantly moving my smd handle and i also used 8mm nozzle for that ...Sir plz guide me where i doing mistakes... Waiting for your valuable reply...😁😁
when removing the black adhesive, apply a little force but you must be careful, then with the hot air, the distance must be a bit high, and do not soak the nozzle, just alternate movements, just move the handle so that the motherboard is not cooked by the heat
Hi, I mistakenly removed the screen and damaged the parts that are to the left of the power IC (2:27-2:29 on your video [at the very left corner of the motherboard]), do you know where I can buy replacement parts for those small modules?
Hello Boss. Yung cp ko kasi habang naglalaro ako naghang. Tapos tinanggal kabit ko yung battery tapos nireheat ko yung charging IC kasi may history na to ng deadboot. Ngayon kahit ireheat ko yung charging IC wala talaga di na nabubuhay. May problema na kaya to sa CPU o UFS tulad dyan sa ginawa mo? Salamat.
wow .. proud ka-bayan here ' my phone is redmi note 10 pro .. and I've been watching your video in CPU Reball for the 5th time .. Hope there's a technician here in Cebu City that works just like you.. May I know the cost of cpu reball ?
Same sila Ng issue sa m3 ko inispriyan ko lng Ng pabango tapos tinapat ko sa airpan pra madrain ung power ic, tapos after 10mins binalik ko lahat tapos umander na, pinatay ko ulit pero gumagana na, unli power on,pwedi xa I power off pero d pweding erestart or reboot
Does it resolve the problem of not booting and charging ? If yes, for how long ? The service center changed the mainboard/motherboard of my poco M3 but I'm afraid it may be in default again.
I had exactly this problem. I drained the battery, until it made no sounds by connecting to the laptop. The draining took 2 days, I knew it because the cp made a peep sound. Then I pressed the power button and the battery symbol - empty - showed up. I connected the cellphone to the socket, then pressed the power and the volume down buttons simultanously. And the cellphone showed "Fastboot". After a while it booted normally and it works again as if nothing happened. I did nothing else, no removing battery, no opening the cellphone case.
Hi, my phone won't turn on and stuck on fastbot/bootloop then CPtechnician said my phone needs to change the EMMC. Is it possible to change that EMMC? Please respond i need a professional advice thank you
SOS my phone doesn't turn on normally, but when I let the battery to run out and connect it to charger the "poco" and battery sign show up but after that when I press the power bottom nothing happens and the battery sign also disappears. Is something wrong with cpu? Or is it Something else?
ang problema .. pag off mo o reboot mo ulit.. babalik nanaman ang problema.. Ipakita mo boss. na rereboot mo kung d na ba ulit mag dedeadbot.. Experienced ko lng den sa Poco M3..
this is what we call professional work
great job explaining in english........ most of the videos on youtube are either in arabic or indian languages....
thanks alot @Tech Tomer
Nice and perfect work..thank you!
Iba talaga pag golden hands ang gumawa👍👍
galing mo dol.lagi ako nag aabang mga vlog repair mo... Quality talaga
maraming salamat dol
@@techtomer pinoy ka pala lods kala ko banyaga e galing
Good work sirji thanks for video 🙏🙏🙏👍👍
galing mo talaga sir sarap paanodin ang mga vlog mo....
Very powerful and clean work 👌 brother thanks 🙏 this vedios
Ganda po nung quality nung video nung repair.
Ok i repaired mine just by heating the cap with my iron for one minute. It was very hot so i believe everything inside as resoldered. It works now, no need for me to open !
Love❤ from❤ India🇮🇳🇮🇳🇮🇳
kawawa naman ung mother board sa na unang technician bosss....mabuti nalang dinala agad jan sa u...kudos to you boss tech tomer...GODBLESS ALWAYS
Great Video , Like and Comment for your channel support , so much annoying job have done and I hope the owner are enough reach to afford this repair 😅
thank you this is a great work 👍
Great experience 👌👌👌
I love your work
Bawat araw sir pinapanood ko video mo. Sana pwede Ako mag training sayo
Taga saan ka sir?
ang lupit idol.,walang bahid ng gin ang kamay hahaha
Ano yung gin dol 😄
lupit talaga dol...
Great job.
Would you pls make a video explaining the ic's allingement.
Cpu Emmc ufs ic write positions...
Best regards.
Very professional experience
thank you friend to tech a good with explanation
Very much thanks sa TUT...!
You will bongo dekhogi Vivo going g to. Mmmnb ho thodi
Wow Amazing work👌
Amazing video sir
Awesome
Which smd machine u use ?
Quick 2008
Nice Job Sir...I have few question in my mind that i m using same Quick 2008 Model smd and try at 360c and 60 air to remove any glued ic but its took too much time and in few cases Motherboard pop up but i constantly moving my smd handle and i also used 8mm nozzle for that ...Sir plz guide me where i doing mistakes...
Waiting for your valuable reply...😁😁
when removing the black adhesive, apply a little force but you must be careful, then with the hot air, the distance must be a bit high, and do not soak the nozzle, just alternate movements, just move the handle so that the motherboard is not cooked by the heat
شكرا لك
After this will it be reset all the apps and files on the phone? Could this be fix without resetting all the phone??
Napakahusay boss 👏 anung gamit mong microscope with camera? You deserve more subscribers 👍
Salamat po
What is temprature of soldering iron to clean CPU and ufs?
Hi, I mistakenly removed the screen and damaged the parts that are to the left of the power IC (2:27-2:29 on your video [at the very left corner of the motherboard]), do you know where I can buy replacement parts for those small modules?
just buy new phone
@@benjiemagdasal615 what's the point of DIY if you're gonna buy a new phonr
hi sir, saan po kayo nakabili ng reballing stencils?
one of the best 👍
Thnx sir but am from Pakistan
Great job ✌🏽🔥
Ano brand ng hot air mo idol?
New subcriber mo rin ako.
Quick 2008
Waooooo kerennnnnn good.....good
I would like to know the microscope you are using
Microscope RELIFE RL-M3T
@@techtomer thanks your work is legitimate
What is your hot air mark please??
What soldering iron you use?
Any good one
where is your shop located?
Hello Boss. Yung cp ko kasi habang naglalaro ako naghang. Tapos tinanggal kabit ko yung battery tapos nireheat ko yung charging IC kasi may history na to ng deadboot. Ngayon kahit ireheat ko yung charging IC wala talaga di na nabubuhay. May problema na kaya to sa CPU o UFS tulad dyan sa ginawa mo? Salamat.
Hi , new subscriber here .. Just wanna what's your location ?
Rizal philippines
wow .. proud ka-bayan here ' my phone is redmi note 10 pro .. and I've been watching your video in CPU Reball for the 5th time .. Hope there's a technician here in Cebu City that works just like you.. May I know the cost of cpu reball ?
Nice thanks to smooth tutorial♥️
Thank
Tech Tomer
top technician
ganyan talaga sakit ng xiaomi? hindi tulad ng ibang brand overprice pero low specs
Same sila Ng issue sa m3 ko inispriyan ko lng Ng pabango tapos tinapat ko sa airpan pra madrain ung power ic, tapos after 10mins binalik ko lahat tapos umander na, pinatay ko ulit pero gumagana na, unli power on,pwedi xa I power off pero d pweding erestart or reboot
Vaaauuuu
Does it resolve the problem of not booting and charging ? If yes, for how long ? The service center changed the mainboard/motherboard of my poco M3 but I'm afraid it may be in default again.
Yes every board having same issue after update
@@AliAhmad-kr2yv Hi, do you know what ROM will fix this? Thanks
magneficent👏👏👏
Which SMD is using in your video??
Quick2008
I had exactly this problem. I drained the battery, until it made no sounds by connecting to the laptop. The draining took 2 days, I knew it because the cp made a peep sound. Then I pressed the power button and the battery symbol - empty - showed up. I connected the cellphone to the socket, then pressed the power and the volume down buttons simultanously. And the cellphone showed "Fastboot". After a while it booted normally and it works again as if nothing happened. I did nothing else, no removing battery, no opening the cellphone case.
How did you drain the battery?
@@alharethxd Just let the cellphone on. until it makes no sound when you connect it to the laptop.
Disconnect and connect battery flex ,your cellphone will be ok.
Sir ,apka repair center location vejo
Tatagal po ba ung reballing repair? Permanent fix
Super sir
mantap jiwa👍👍
After restart my poco cant power up. Hart reset cant help. A few days after i can turn on. What do you think about this?
Is perfect.!
how much it might cost sir?:D
Thanks sir
parang rewa gumawa ng vids nice
Fixing this damn $150 phone cost more than the phone itself
ano gamit mong hot air lodi
quick 2008
@@techtomer nice thank you god bless
mabuhay ang mga tech tomer hahahah
Which brand hot air gun is that
Quick 2008
Congrats final solution napo ito? Hindi yung bunot caps? Pwede ask sir ano flux paste gamit mo din?
Local AMTECH Flux lang po
very nice 👍
Very clear
Ic replacement ke baad phone me koi problem hoga
Na
Hi, my phone won't turn on and stuck on fastbot/bootloop then CPtechnician said my phone needs to change the EMMC. Is it possible to change that EMMC? Please respond i need a professional advice thank you
how much po mgpagawa sayo sir ??
im just gonna buy new phone thanks..
Are you from philippines? I wanted to send phones for repair
Rizal area po
@@techtomer send address mo na lang boss, ipadala ko via j and t
@@jackyjfbaaranda9594 paki message po ako sa fb page ko
Hi, sir mera poco m3 switch off honeki baat on nehi hua..mechanic ne kaha motherboard problems..9000/-lagega kaha any solutions
do you have fb account? i'm also having the same issues on my phone and i would like to request for a repair if it's ok. i'm pinoy too btw
I wish I could get such a mobile service in Bangladesh😭
Sir pwede mag training Sayo .
SOS
my phone doesn't turn on normally, but when I let the battery to run out and connect it to charger the "poco" and battery sign show up but after that when I press the power bottom nothing happens and the battery sign also disappears. Is something wrong with cpu? Or is it Something else?
Good ❤❤❤❤❤
Why this issue happens for many Poco M3 devices?
love ❤form❤Burmese❤
🇲🇲🇲🇲🇲🇲
sakin boss ung front cam ko error ano kaya nangyari
alisin mo lahat ng camera tapos test mo isa isa camera
Good
Done master
nhiệt đô 420 có qua cao không vậy
pa shout out master sa next video mo
Sure
Wow
in 99% just warm up the little chip on the left! without taking it off!
Are you in Pakistan my poco m3 have the same problem and everyone is saying it can't be repaired I am not rich plz help
Karor laesn
Mere mobile be kharab hochuka hai AP Tek karsakty ho
Why no videos now
sir, what is the SMD station u use
Quick 2008
Nic
❤️❤️
Hlo boss my poco m3 Dade please helpe
Oppo a16 motherboard chiya please
may pm po ako sa fb. paseen po
ang problema .. pag off mo o reboot mo ulit.. babalik nanaman ang problema..
Ipakita mo boss.
na rereboot mo kung d na ba ulit mag dedeadbot..
Experienced ko lng den sa Poco M3..
Kung nasubukan mo na reworks ang CPU at UFS alam mo ang sagot yun lang po thank you.
Компаунд специально заливают.
❤❤❤❤❤❤❤❤❤❤❤❤