My Eagle 1000 FSC Reverse Loop light comes on The gate won’t close or open now What should I do? The Photo Eye’s green lights come on though and when it hits the reflector, the red light(s) comes on as well What should I do? I bought an EMX-50-325 and it has a common wire. My board has no common connector though. My board has 2 hot 24 VAC wires so do I just connect both hot wires on the EMX Photo Eye to the 2 hot on the board. How about the common wire?
It sounds like you have a lot going on with your operator; if your reverse loop light is going on when it shouldn't, you probably have a problem with your in-ground loop and it needs to be replaced. You could try power-cycling the operator to clear the light, but this may just be a temp fix. Regarding your photo eye, make sure it is properly aligned with your reflector. There are typically two lights on a photo eye, one to indicate power and one to indicate alignment. There may be a third to indicate an obstruction. Regarding attaching your EMX photo eye, all control boards should have a Common terminal. I am not familiar with your Eagle operator, it may only work with propitiatory products.
John, this video is very helpful. Thank you. Can I adapt what you have shown to install a GSM? I have a GSM I would like to install so I can open the gate with my phone am not sure what to connect it to.
The relay for opening devices, such as a GSM, would be attached to the RADIO OPEN terminal and COM terminal on the main board. This is not the same terminals described in this video for attachig entrapment protection devices.
Programming for remotes is not completed directly on the HySecurity gate operator itself. Instead, there is an auxiliary radio receiver box/antenna that has been wired to your gate operator. This auxiliary radio receiver box is typically installed right inside of the gate operator and will have an antenna connected to it. Can you identify the manufacture/model of the radio receiver box that you are using? Common manufactures might be Linear/Tri-Code/Multi-Code/LiftMaster/DoorKing/Delta.
That was a very helpful video! Thank you, John Allen, for helping me with my first Slidesmart15DC install. I wish I had you on speed dial.
Is there a way to get rid of entrapment mode and having to manually reset it every time?
Please give Solution for error 6
Very interesting, I learned a lot.
My Eagle 1000 FSC Reverse Loop light comes on
The gate won’t close or open now
What should I do?
The Photo Eye’s green lights come on though and when it hits the reflector, the red light(s) comes on as well
What should I do?
I bought an EMX-50-325 and it has a common wire. My board has no common connector though. My board has 2 hot 24 VAC wires so do I just connect both hot wires on the EMX Photo Eye to the 2 hot on the board.
How about the common wire?
It sounds like you have a lot going on with your operator; if your reverse loop light is going on when it shouldn't, you probably have a problem with your in-ground loop and it needs to be replaced. You could try power-cycling the operator to clear the light, but this may just be a temp fix. Regarding your photo eye, make sure it is properly aligned with your reflector. There are typically two lights on a photo eye, one to indicate power and one to indicate alignment. There may be a third to indicate an obstruction. Regarding attaching your EMX photo eye, all control boards should have a Common terminal. I am not familiar with your Eagle operator, it may only work with propitiatory products.
John, this video is very helpful. Thank you. Can I adapt what you have shown to install a GSM? I have a GSM I would like to install so I can open the gate with my phone am not sure what to connect it to.
The relay for opening devices, such as a GSM, would be attached to the RADIO OPEN terminal and COM terminal on the main board. This is not the same terminals described in this video for attachig entrapment protection devices.
@@totalsecuritywarehouse3621 Thank you. I will try it
How do I program a remote? I can’t find it anywhere
Programming for remotes is not completed directly on the HySecurity gate operator itself. Instead, there is an auxiliary radio receiver box/antenna that has been wired to your gate operator. This auxiliary radio receiver box is typically installed right inside of the gate operator and will have an antenna connected to it. Can you identify the manufacture/model of the radio receiver box that you are using? Common manufactures might be Linear/Tri-Code/Multi-Code/LiftMaster/DoorKing/Delta.