Hi thanks for video. The Wife was looking to replace kettle and toaster 😬 so you’ve saved me £60plus. My middle screw was a torx screw in case anyone else can’t remove it. Outside screws Phillips.
You have saved me from replacing my broken toaster!!! Only been using one half of it for months as the other wasn’t working, and now it’s fixed! Incredible work! Thank you so so much.
Took me a while to find out that there are two more screws hidden behind the back rubber stoppers. Once I could open it, it was easy to clean and that sorted out the problem. Many thanks!
Thanks from America! Was about to spend $200 on a new Smeg toaster, but my Breville is working again. My model appears to be impossible to open, but violent shaking and compressed air blasts did the trick.
Couldn't get in mine as the screws were triwings! Still toaster upside, shaking and hammering the lever seems to have fixed the problem, so your vid still inspired the solution- and saved me 60quid thanks
Brilliant. I had taken the cover off several times and cleaned the inside but hadn't cleaned the little magnet. I was about to buy a new one then watched this. It now works. Good man.
Brilliant that , nothing lasts anymore, my mother has one from 1984 , not a thing gone wrong in all the years , this new stuff is made not to last I think ! 👍🇬🇧🇬🇧
Great video, very helpful, saved us buying a new toaster, ours had some screws at the back also, star type in the middle and two normal screws in either corner which the feet had to be removed (easy enough with tweazers) to get to.
Great video but I still have 2 outside elements not heating. Left side all good and right side centre ones work. Doesn't seem to be a break in any wires either. Any advice please?
I have to replace a lost button on mine, I was able to obtain an extra defective unit so I have spare parts, just not sure how to remove the buttons, any advice?
I have the same problem and exact same toaster (model number the same) I’ve taken out the 3 screws I just can’t get mine apart even tried a 4th screw but I can’t find anymore
Just done this and was a success. Something you think they could easily protect more if you think about it, but then again their sales would go down so i am guessing its a business decision not to innovate a solution for something as simple as crumbs in the way 🤔
Thank you sir, this fixed the same problem for me - honestly the sensor area on the effected plate was not too bad on mine, only a couple of crumbs so I wondered if my issue lay a little deeper, though sure enough, I cleaned that area out, but it back together and it's working again!
Hello, I do not know if you can answer me but I have a problem with my cash register. I don't know why when you want to make a header it is not saved correctly. I don't know if you know any solution
Thank you for your message and for watching our videos. If you have a Casio till please check out our sister channel: ruclips.net/user/CasioHelp Thanks, Shopstuff
![Blox Fruits Dragon Rework Update [Full Stream]](http://i.ytimg.com/vi/EqDAp8udhm0/mqdefault.jpg)
Hi thanks for video. The Wife was looking to replace kettle and toaster 😬 so you’ve saved me £60plus. My middle screw was a torx screw in case anyone else can’t remove it. Outside screws Phillips.
You have saved me from replacing my broken toaster!!! Only been using one half of it for months as the other wasn’t working, and now it’s fixed! Incredible work! Thank you so so much.
Just tried your advice and it was spot on, haven't used the right hand side for months and now we can. Thank you for your helpful video.
Took me a while to find out that there are two more screws hidden behind the back rubber stoppers. Once I could open it, it was easy to clean and that sorted out the problem. Many thanks!
Thank you, I needed this comment. Toaster now working
Thanks. I was at that point of 'bending' the front part a bit too far. This got me sorted 👍
How to remove rubber stopper??
Thanks from America! Was about to spend $200 on a new Smeg toaster, but my Breville is working again. My model appears to be impossible to open, but violent shaking and compressed air blasts did the trick.
Couldn't get in mine as the screws were triwings! Still toaster upside, shaking and hammering the lever seems to have fixed the problem, so your vid still inspired the solution- and saved me 60quid thanks
Same here. There I was armed with both Philips and Torx screwdrivers and it chucked that curve ball at me! 😂
Brilliant. I had taken the cover off several times and cleaned the inside but hadn't cleaned the little magnet. I was about to buy a new one then watched this. It now works. Good man.
Thankyou. Likewise. Saved the toaster from the unnecessary bin and me dismantling and forgetting how to assemble it.
Brilliant that , nothing lasts anymore, my mother has one from 1984 , not a thing gone wrong in all the years , this new stuff is made not to last I think ! 👍🇬🇧🇬🇧
Thanks man, saved me buying another toaster and a bit of landfill waste!
Worked for me! 20 minutes, took me longer to find a screw driver small enough to fit in the holes :)
Oh boy, brilliant, took me twenty minutes, job done, thank you.
I whacked my Breville 3 times on the counter. Worked a treat
Thank you for sharing this video, you just saved us buying a new toaster.
Great video, very helpful, saved us buying a new toaster, ours had some screws at the back also, star type in the middle and two normal screws in either corner which the feet had to be removed (easy enough with tweazers) to get to.
Thanks for this video. We had the same toaster and it wasn't staying down. Taken apart and found lots of crumbs.
Thanks for this, just saved myself £45 on a new one!
This worked! Although I did have to remove 6 screws, 2 of which needed a very specialist hexagonal bit which fortunately my neighbour had.
Awesome stuff mate!
Just saved me £22, cheers buddy!
Great video but I still have 2 outside elements not heating. Left side all good and right side centre ones work. Doesn't seem to be a break in any wires either. Any advice please?
Brilliant thanks, saved me buying a new toaster
Thank you very much. This video enabled me to resolve problem without removing buttons, which is a faff!
Yep, sorted a similar machine for me. I had to use a file on the points as they were very dirty. Many thanks! 👌
I have to replace a lost button on mine, I was able to obtain an extra defective unit so I have spare parts, just not sure how to remove the buttons, any advice?
Thanks for this post …spot on with the advice…crumbs on the sensor it was …Cheers..
Great tip, worked on my toaster. Thanks.
Worked great on my asda toaster thank you!
Thanks worked for me, Thank heavens for "RUclips".
Outstanding! Thank you , kindly!!! It worked!!!
I have the same problem and exact same toaster (model number the same) I’ve taken out the 3 screws I just can’t get mine apart even tried a 4th screw but I can’t find anymore
There was two hiding under the back two rubber feet i had to remove. May be the same for yourself 😃
Cheers saved me 35 quid on and thats discounted🎉
I’ve got the same problem. Anyone know where I can buy the correct sized screwdriver please? Bought 2-3 already but they’re the wrong size!
Thank you for the video.
Good job.
Just done this and was a success. Something you think they could easily protect more if you think about it, but then again their sales would go down so i am guessing its a business decision not to innovate a solution for something as simple as crumbs in the way 🤔
u save my toaster. thx thx bro!!!
So helpful. Thank you very much.
spot on thanks it sorted out toaster !!
Thank you sir, this fixed the same problem for me - honestly the sensor area on the effected plate was not too bad on mine, only a couple of crumbs so I wondered if my issue lay a little deeper, though sure enough, I cleaned that area out, but it back together and it's working again!
Cheers for this. It sorted mine
Sadly, that didn't work for me! Any other suggestions, please?
Hello, I do not know if you can answer me but I have a problem with my cash register. I don't know why when you want to make a header it is not saved correctly. I don't know if you know any solution
Thank you for your message and for watching our videos.
If you have a Casio till please check out our sister channel: ruclips.net/user/CasioHelp
Thanks,
Shopstuff
Thank you, fixed!
Thanks so much for your advice
Cool mate, I fixed mine 🎉😂
Fantastic, thank you.
Yeah just onto ours same 1 but removed the cover entirely..gonna use compressed air to blow it all out to cause isopropyl alcohol to clean
Great video, thanks
Thank you so much 😊
Screw out but machine not opening
thank you mate 👍
THANKS
My problem is the opposite that it doesn't pop up
pop some crumbs in! :)
Toaster working great again. That one screw was a b£@#&.
I'll give it ago
Great advice thank you
Thanks