εγώ το χρησιμοποιώ για να κολλαω αλουμίνιο μεAC- tig περισσοτερο,,..και μου βγαίνει τζάμπα σε σχέση με μια AC-tig του εμπορίου, συνδεω την tig τσιμπιδα κατευθείαν στην παλιά ηλεκτροκοληση και κολλαω αλουμίνιο.
@@zuzuniagrikubanos6473 με συγχωρείς γιατί δεν πρόλαβα να δω ολόκληρο το βίντεο και ίσως το αναφέρεις μέσα... κολλάς αλουμίνιο απευθείας από την έξοδο του transformer δηλαδή με 60hz και το current limit που ρυθμίζει με το μοχλό ; τι αποτελέσματα έχει και πόσο γρήγορα σου τρώει τις μύτες ; ρωτάω γιατί ενδιαφέρομαι να δοκιμάσω κάτι αντίστοιχο. Επίσης τι αέριο χρησιμοποιείς;;
@@pipoeng Στην Ελλάδα έχουμε 50hz και ναι όπως σωστά κατάλαβες κολλάω αλουμίνιο κατευθείαν από το transformer , οι μύτες δεν τρώγονται καθόλου απλά κάνουν μπάλα στην άκρη, και χρησιμοποιήω σκέτο argon. Αυτό που πρεπει να προσέξεις ειναι οι ράβδοι που θα χρησειμοποιησεις, για το καλύτερο αποτέλεσμα να βάλεις AL.MG 5 / 5356 το αποτέλεσμα ειναι ικανοποιητικο αρκεί να συνηθίσεις το σταθερό current που ρυθμίζεις με το μοχλό. αν θέλεις να βάλεις μεταβλητό στο current μπορείς να χρησειμοποιησεις ενα variac και ένα foot switch
@@MohibAssalem i have for you beter solusion !!!! you culd use starters from neon lamps = www.google.gr/search?q=starter+for+fl+lamp&sca_esv=ecf90fb16855ea79&udm=2&biw=1600&bih=781&sxsrf=ADLYWILh7XUB6hjyOXaNrFUcRf0kkPX7EQ%3A1729839605387&ei=9UEbZ_2eF5ro7_UPqsm2wA8&oq=starter+for+&gs_lp=EgNpbWciDHN0YXJ0ZXIgZm9yICoCCAYyBRAAGIAEMgUQABiABDIFEAAYgAQyBRAAGIAEMgUQABiABDIFEAAYgAQyBRAAGIAEMgUQABiABDIFEAAYgAQyBRAAGIAESJDPAVCACVicoAFwBXgAkAEAmAHxAaAB7BSqAQUwLjcuN7gBAcgBAPgBAZgCD6ACug_CAgQQIxgnwgIEEAAYHsICCBAAGAUYHhgPwgIGEAAYCBgewgIIEAAYCBgKGB7CAgYQABgFGB6YAwCIBgGSBwU1LjUuNaAH4zs&sclient=img it is beter
Hearty congratulations for your effort in presenting videos in the English: Language, you deserve high marks. Your attitude towards learning is brilliant and that goes for your interest in welding, electronics, and languages, and anything else in life. I am a little worried about the " special component" sparking and the welder arcing through it! as it seems to be installed at a location where it could be replacing the torch itself!! I have to think more about this. Again well done.
don't think about it, just try it,, ,I discovered it by accident after connecting a series of resistors I saw that in a resistor with a defective cover, let the high voltage pass through the skin.
@@zuzuniagrikubanos6473 Great. Is it possible to replace the special component with a resistor and capacitor mounted in series to prevent hf from returning back to the transformer and destroying it? Thanks
@@GP-zm2kd I fully agree that the special component can be replaced with a capacitor of value that would be a short circuit to the HF and an open circuit to the welding set frequency. I did that without the series resistor included but I fully agree with you a low-value resistor would not do any harm as the HF current is low. It is interesting how displacement current ( capacitors) can be substituted for conduction current ( current through an arc or copper flow ) James Maxwell knew what he was doing when he wrote Curl H= J + dE/dt. as that is what is contained in the welding set with HF start.
@@zuzuniagrikubanos6473 This chock coil, is it necessary to connect it to the positive terminal? Or is it important that it be inside the electrical circuit?
@@MohibAssalem i connect alweys on positive terminal, it helps on the scrats start ,,, it is a self-induction componet,,it can work without chock if you dont care about scrats start. look this = ruclips.net/video/Rblr6qrJ6UM/видео.html no hf starter...
I didn’t need the English cc. Very good Video. Just curious what is the special component I must have missed something. Or maybe my ability’s are not up to doing something with adding High Frequency to a standard inverter welding machine. Can you tell me more on this subject. Thank You fo the knowledge I’ve gained from this video already
Καλή χρόνια με υγεία !!! Τι εξαρτήματα χρειάστηκες για την κατασκευή; Έχω και ‘γω μια παλιά ηλεκτροκολληση και θέλω να την μετατρέψω.... δεν ξέρω αγγλικά....
Ευχαριστω για τις ευχες, τα εξαρτηματα περιγραφονται στο σχεδιο και αν και ειναι στα αγγλικα το σχεδιο ειναι universal,,δηλ, στο σχεδιο βλεπουμε μετασχηματιστες, διοδους, συνδεσεις, κλπ. για να κανεις μια κατασκευη πρεπει να καταλαβενεις [διαβαζεις] σχεδιο,, εγω βλεπω γιαπωνεζους που περιγραφουν σχεδια και δεν καταλαβενω γρι γιαπωνεζικα,,,ομως καταλαβενω [διαβαζω] ηλεκτρονικο σχεδιο,,, δεν προκειτε απλα για μερικα εξαρτηματα που τα αγοραζεις και τα βαζεις επανω,, προκειτε για ''πατεντα'' που αν δεν ξερεις τι κανεις μπορει να παθεις ατυχημα ηλεκτρισμου που ειναι πολυ επικίνδυνο, οι πληροφοριες που εχω σε αυτα τα βιντεο ειναι υπερ-αρκετες, για καποιον που ξερει τι κανει,,διαφορετικα βρισκεις εναν φιλο σου ηλεκτρονικο και στο φτιαχνει αυτος.
You my friend are a very smart man. Just a word of caution, be very careful of EMF generated by high frequency arcs. Keep in mind that EMFs generated by high-frequency welding equipment and components, such as inverters and pulsed welding processes, may produce an additional type of EMF, known as radio-frequency (RF) radiation. RF energy radiates through space in the form of wireless waves or digital pulsing. Human blood contains iron and other minerals and there are studies that show how our blood is affected. This is not widely publicized because it will cause negative impact to the welding industry. There is no other technology to weld metal at the moment so it is kept quiet. We have heard of the dangers of RF from mobile phones, RF from HF welding is much more powerful. Stay safe.
what you mention is correct and certainly human bodies are affected by electromagnetic waves such as cell phone radio or wi fi or satellites and even hv pulses but the human body regenerates if we maintain a balance way of life away from toxins, smoking, stress, and poor diet.
I thought RF radiation was non-ionizing - just heats up cell tissue or some such. Can't recall where I read that. The majority of transformer based welders are stuck at 50-60 hertz depending on your local power supply. There are some wicked expensive Transformer TIG units that have frequency adjustment but I don't know if anyone makes units like that anymore. And those units have been around for a long time. If there was a serious risk (other then the usual and known risks like welding with a pacemaker) associated with HF produced by inverters and high end transformer TIG machines then wouldn't the industry would revert to "old" transformer welders? Go back to using exotic gas mixes to weld any relatively uncommon metals, colorless stainless welds etc?
@@brianlittleforest631 The profits from the technology are immediate, the consequences and costs are deferred to the future you, the timeline for definitively recognizing the problem far exceeds and preempts the timeline for litigating compensation. Health really cant be compensated financially anyways, so beware.
@Nicole Yenson that was whole lot of typing to tell me nothing. Be wary . . . why? By what manner and mechnism will HF welding cause harm? HF inverters units have been around since the 80's and the guys who are retiring out now are still suffering from the usual effects of welding long-term, skin cancer (usually arms) emphysema etc. Seems to me I'm better off investing in the usual PPE - respirators and UV protection rather then wasting the effort to protect myself from a non-existent hazard. I have one C.C. machine capable of 250 hertz AC and DC pulse adjustment which has got to be a wide wave length - must be upwards of 1000 km wide I don't know exactly how wide of the top of my head. Other machines can do up to 500 hertz. Since mine is square wave machine the part that uses HF to start the arc is momentary @ 2 Mhertz. Which is about the same wavelength as AM radio. Sorry, but I call B.S. HF can be fatal for sure. But in the way grabbing a live wire can be fatal.
That be well and God bless you all, really meant alot , and I subscribe to your channel! And thanks for the info, I was wondering how they ran two signals on a single circuit , thank you very much, for your time and knowledge, and thanks for the effort to make us understand! Have a great day!
Great stuff man! Thanks a lot! I have a question 🙂 Would be nice to figure out if it’s possible to make a trigger switch for the Lincoln Electric Speedtec 200C machine? Not HF, just a switch to stop the arc when finished welding.
You have invented something I have been looking for and your video is amazing, thankyou so much. I have an old transformer welder and have been meaning to make an AC TIG from it for a couple of years so I could Weld Aluminum. I bought a HF generator off ebay so I am good to go. I am also interested in a couple of things on the DC version if you do not mind. a) why have you put the "Simmer Coil" and big inductor in the in the ground side. b) what is the unction of the Diacs. May thanks again. PS do you have any videos of you using this to Weld Aluminum
aluminium welding = ruclips.net/video/5V7aUaB0A1A/видео.html and = ruclips.net/video/KbTm4J6Xmpg/видео.html simmer coil = ruclips.net/video/bjG6Gfjffmk/видео.html big inductor = is for more soft and continius work the Diacs = is for extra protection of the diodes from simmer Hi-voltage spaiks
Hello my friend, I congratulate you on your great work, after watching your videos I made a tig machine and it works very well, there is only one detail that I cannot find why it is, it turns out that it consumes a lot of current through the primary of the main transformer when welding, yes I put the output at 200A in the primary, it consumes almost 100A, and that only happens when I use my machine as a tig, has it happened to you? Do you have any contact where I can exchange with you about these wonderful tig welding machines? Greetings from Cuba, Central America and the Caribbean
most likely you have a leak in one of your coils and when you use the high frequency in the tig it makes an arc inside the coil and increases the consumption,,,check or rebuild the special componet whose use is that the high frequency does not affect the coil but is transferred directly to the welding point,, if this does not correct the problem then you need another welding transformer or to locate the leakage by unwinding and re-winding the primary and secondary coils. in this link you can contact and upload a photo if you need more help. = doityourself123.forumgreek.com/t505-topic
Hello, do we need a large current and voltage at the same time with the gas out, to get a good weld, or do we need a large effort with gas only, and why does the user not be electrocuted if there is a current and a large voltage at the same time, please reply and thank you very much
it is about two different current values in the same conductor, one with a few volts and many amperes and one with thousands of volts and zero current,,,but there is always the risk of electric shock...
new subscriber because i love how you get a kick out of your "special component" also thank you very much for helping me with this video! i recently bought a tig/mig/plasma welder and didnt realize that it was a DC only. I am hoping that i can some how convert it to AC/DC. so with this video and your other video i hope to have all that and hf start ( which i may have since i dont believe it scratch start) . if you can answer this question for me that will be amazing! in a DC welder does the transformer produce AC current, which is then fed into a full bridge ractifier to get DC ?
thanks for the comments, i love it. as for your question = an inverter welding works with pulsed rectified voltage and so you can not get AC voltage,,you need either a very sophisticated inverter or a simple welding transformer as I do in the video,,the transformer is cheap and does the job perfectly at AC 50Hz.
@@zuzuniagrikubanos6473 thank you very much! so just to make sure i have a full understanding. ill need 2 transformers a welding transformer for my ac/dc (adding full bridge rect to get dc) and a smaller transformer for HF ( like from an old crt tv) correct? again thank you very much i look forward to your videos very informative and to the point!
@@issaproject This is my web page = doityourself123.forumgreek.com/ make a connection and we will analyze all the stages of construction,,send me a personal message or make a post on the topic=doityourself123.forumgreek.com/t505-topic#6957
I need your help, I am total newbie, how would schematic look if there is no rectifier, because I have dc inverter maschine and i want only dc welding.Thank you in advance.
Estimado Zafdeep. Posiblemente Zuzuni, no pudo agradecer tu comentario por estar muerto. Su muerte pudo deberse a electrocución, al haberse perforado el aislamiento entre primario y secundario ( y/o gabinete) del transformador 220/50 VCA. Aislamiento típicamente pensado para tolerar un par de miles de voltios. Especialmente, usar la configuración que definió como DC, es la más grave. El aislamiento se puede ir degradando lentamente, hasta que en algún momento el nivel de carbonización es lo suficientemente alto para electrocutarte. El dispositivo tiene que tener el apropiado aislamiento y supresores de descarga, para evitar el tipo de problemas descrito previamente. Saludos.
El positivo va como masa en la base como la sold electrica y la parte que agarraria el electrodo es negativo el centro bien el mapa.bien claro gracias sr Arg
Where u get high frequency board ebay? which one? . so this box is or is not connected to the other welder? .. im confused why you have another giant welding transformer in the box if you connected the other welding box to this gray box.?
the gray box is a rectifier for DC Tig for AC i conect direct to welding box,, the big transformer in the gray box is a filter chok with only one coil. For the hf board I do not advertise, take whichever you like.
What is the link to where you describe the special component SCS? What voltage is the diac and what kind and value for the capacitors across the bridge, the part number for the High current diodes and how many are used (for example if many in parallel), and how to construct the huge high amps chock (i.e. how many henries) for the DC side TIG circuit? Please provide this info either in the description or answer me directly, Thanks.
χρηστο....στο βιντεο τα περιγραφω μια χαρα,, τωρα αν θες περισσοτερες λεπτομεριες φτιαξτο και βρεςτα ολα αυτα,,, εγω τι να πω που τα φτιαχνω και δεν ρωταω κανεναν ?? αν εχεις λιγες γνωσεις μια χαρα θα το φτιαξεις,,αλλιως αστο-παρατατο...
@@zuzuniagrikubanos6473 Signomi min thimonnis apla mia aporeia eixa gia ta exartimata. alla se afto to video einai sxedon se block diagram. Apla mporouses na me parapepsis sto timestamp pou mas fotizei ti telos panton einai afto to SC (mipos einai snabber?)
@@christosmakariou4574 το SC το κατασκευαζω ζωντανα στο βιντεο απο ενα ηλεκτροδιο και λιγο συρμα,, αν δεις προσεκτικα το βιντεο θα το δεις, προκειτε για ενα sparc-gap ουσιαστικα και οχι snubber που μεταφερει απευθηας την υψηλη ταση στην γειωση.
Great. Is it possible to replace the special component with a resistor and capacitor mounted in series to prevent hf from returning back to the transformer and destroying it? Thanks
Try it and tell me the result. Do not forget to tell me the value of the resistance in watts and ohms,And the value of the capacitor in volts and farads. thanks in advance.
@@zuzuniagrikubanos6473 Thanks for your attention. I am thinking of a filter consisting of an 8 Ohm 25 W resistor in series with a 12 microfarad 250 V capacitor. This filter should protect the transformer upstream of the filter. However your solution is very cheap and this is good. Thanks bro.
I have a PS4. Where the hard drive connects to motherboard, the solder on the connection at the motherboard (where the hard drive connects to motherboard) it is cracked up n is messing up. Can I trace those cracked solder leads n add jumper wires to where they connect elsewhere on the motherboard? Thank you.
@@zuzuniagrikubanos6473 I'm not sure yet as I don't know whether there are visible leads to the end of circuit. Besides I'm so darn busy right this moment. I ended up getting covid a month ago and it really done me in so I got behind on my personal work. I'm getting much better now but it's taking me time. Plus we gotta big family. I will look. Do you have Facebook? If so you can add me. Chad Moyer. Thank you bub n remember I'm in USA....Ohio so time is different. Thank you
@@chadmoyer1453 i dont have Facebook, i getting covid a month ago too,,,, it was not a big deal,, 4 days of fever and 4 days of cough, I did not take any medicine nor a vaccine. have fun and everything will be done.
@@zuzuniagrikubanos6473 be alright if you did for communication purposes. It's really good for that. Plus you can get ur channel out there more. Ive shared a few of your videos. But covid messed me up. I still have small issues; plus I have skitzo n bipolar and a blowed out hip. After I healed up some from covid, it sat in my hip for a few weeks. I'm better now thank God. I can run n work even more now but I've got a lot to catch up on. Therefore if I don't communicate much now it's ok because I really enjoy electronics. I mainly have residential grade electrical skills, but picked up some industrial/commercial (3-phase…switches) as well as low voltage. But electronics is not my area right now to be any confident in, but having a friend surely helps... thank God.
@@chadmoyer1453 If you like electronics the best way to learn - find out is to buy a cheap oscilloscope, a cheap power supply and a cheap multimeter and start to make this = talkingelectronics.com/projects/50%20-%20555%20Circuits/50%20-%20555%20Circuits.html?=true&width=100%&height=100% once you make a few circuits you will understand many things. in the link I show you it has low voltage circuits that are relatively harmless and have a pleasant and useful effect. At the same time you will discover that many of our fellow human beings deal with electronic constructions as a hobby and soon you will meet many friends who like the same thing. but if you do not use a soldering gun,, with the theory alone you will not achieve anything. I am not an electronic ,, I am just a carpenter who likes constructions and new knowledge ,, a hobbyist you can say. I will help you as much as I can but as you understand you are the one who will make a construction from alpha to omega.
Zuzuni...Good night...excuse me my inglish isnt so good ...your work and vídeo can help me very much.But would be possible you send me the value of all components such diods,capacitors and so on.I will get and thankful for this help. Your edres is not available to me.Thanks.best regards .
This „special component” is basically a voltage dependent resistor? I don't understand the role of the capacitors and the diacs on the diode bridge. The purpose of the „special component”, and the capacitors, and the diacs together, is to protect the welder's diode bridge from the high voltage? Please give me a detailed explanation. You can use your language, if it makes easier to explain, i can translate it.
the capacitors, and the diacs together, is to protect the welder's diode bridge from the high voltage The purpose of the „special component”, is to connect the ground and the electrode to simmer coil.
If I understand it correctly the SC is a spark gap. The first inductor on the DC version does not conduct high frequencies but can pass the 40v for the welding current. This way you can apply a high voltage between the tool and ground without the HV getting shorted out by the thick welding wire. Because the first inductor is effectively removed from the circuit as far as the high voltage is concerned you need a device to close the circuit for the high voltage but not short out the weld current. The spark gap allows this.
Hey thanks so much for doing this video! Thanks for specifying the capacitors and diodes in another comment as well. I've got all the components ready now. Just before I put it together can you please confirm the very last component you drew. Is it a pair of opposing diodes, or something else? At 27:06.
@@zuzuniagrikubanos6473 και εγω θέλω να βρεθούμε εχω ενα κύκλωμα που πιστεύω θα σου λύσει τα χέρια με το EN 555 με είσοδο 12 vdc και βγάζει 35.000 v με διακοπτομενη είσοδο. Εγω απο αγυια είμαι
It doesn't work as real HF starter tig welder... half time you perform a lift start.. maybe you should increase the voltage? Clearly you are welding on dirty surfaces and maybe this is the reason why your arc's not start
it is only a demo... in dc mast have sharp point on tungsten and clear surface.. in ac is d'ont mater... its start watever surface or tungsten conticion the ark starts from heet and a sharp point heets esyer like here= ruclips.net/video/Rblr6qrJ6UM/видео.html
@@zuzuniagrikubanos6473 Ok ok you convinced me! I never weld with tig machine and I always ask my self if is better to buy a good MMA welder for a reasonable price (lincoln for example) amd transform it in HF tig with a circuit like yours (thanks for it) or buy directly a mediocre tig welder for chip price.
Thirty minutes to tell you nothing, what he has shown is wrong! What on earth is a "special component"? 25A x 220v= 5.5Kw, 40 x 200=8Kw, getting more out of the transformer than he's putting in, magic! The high frequency cct is on the torch cct not in the return. What that DIAC ( DIACS, by the way are signal level components used to trigger triacs) is supposed to do is anyone's guess? There's no date on this post so I must assume it's an April fools joke...🤣🤣🤣🤣🤣
Γεια σου ικαρε σαββιδη με τα ωραια σου.... !!!!! παρεπιπτοντως σε ολο τον κοσμο μετα τα βιντεο μου φτιαχνονται διαρκως τετεια μηχανηματα.. πχ = ruclips.net/video/EUuWTZwcvSI/видео.html&lc=Ugwufg4JdpUMAEKf6Gt4AaABAg
If you don't understand what H f is don't bother.......don't write in Arabic to a Greek,,, make the effort and write in English so that someone might want to help you, to make it easy for them
@@zuzuniagrikubanos6473Thank you for your response. I am an Arab from Algeria. I would like to help you. Your mother, where can I find the HF and SC parts?
![let's make a AC- PULSE tig and stick welding machine with HF arc starter [schematic on video]](http://i.ytimg.com/vi/ti6RkIbA93o/mqdefault.jpg)
![let's make a AC- PULSE tig and stick welding machine with HF arc starter [schematic on video]](/img/tr.png)
Thank you for taking the time to teach, it is appreciated. Your English is perfectly understandable I'm glad you chose to do so.
thanks alot from italy! in the schematics... whats the special component?
SK = chek 4.10 minnute of the video for it.
@@zuzuniagrikubanos6473 that’s genius! I’m trying to make my plasma cutter machine, do you think can work your machine?
@@RulofMaker yes !!! i think it my self for a big plasma cut.but i will need a biger torch.. now i have a 40Amp comercial plasma .
Great work it's awesome to build your own equipment and use your own creations to do what the super expensive machines do congratulations
Πολύ χρήσιμο το βιντεάκι σου, αν κάποιος ψάχνει για τέτοια ηλεκτροκόλληση.
εγώ το χρησιμοποιώ για να κολλαω αλουμίνιο μεAC- tig περισσοτερο,,..και μου βγαίνει τζάμπα σε σχέση με μια AC-tig του εμπορίου, συνδεω την tig τσιμπιδα κατευθείαν στην παλιά ηλεκτροκοληση και κολλαω αλουμίνιο.
@@zuzuniagrikubanos6473 με συγχωρείς γιατί δεν πρόλαβα να δω ολόκληρο το βίντεο και ίσως το αναφέρεις μέσα... κολλάς αλουμίνιο απευθείας από την έξοδο του transformer δηλαδή με 60hz και το current limit που ρυθμίζει με το μοχλό ; τι αποτελέσματα έχει και πόσο γρήγορα σου τρώει τις μύτες ; ρωτάω γιατί ενδιαφέρομαι να δοκιμάσω κάτι αντίστοιχο. Επίσης τι αέριο χρησιμοποιείς;;
@@pipoeng Στην Ελλάδα έχουμε 50hz και ναι όπως σωστά κατάλαβες κολλάω αλουμίνιο κατευθείαν από το transformer , οι μύτες δεν τρώγονται καθόλου απλά κάνουν μπάλα στην άκρη, και χρησιμοποιήω σκέτο argon. Αυτό που πρεπει να προσέξεις ειναι οι ράβδοι που θα χρησειμοποιησεις, για το καλύτερο αποτέλεσμα να βάλεις AL.MG 5 / 5356
το αποτέλεσμα ειναι ικανοποιητικο αρκεί να συνηθίσεις το σταθερό current που ρυθμίζεις με το μοχλό.
αν θέλεις να βάλεις μεταβλητό στο current μπορείς να χρησειμοποιησεις ενα variac και ένα foot switch
Understanding electronics is very hard for some people. My respect to you, as a welder, for learn hard to understand electronics.
Can I do without ceramic capacitors connected in parallel with each diode inside the bridge?
no-nin-niet-niente-لا يوجد-Hayır
@@MohibAssalem i have for you beter solusion !!!! you culd use starters from neon lamps = www.google.gr/search?q=starter+for+fl+lamp&sca_esv=ecf90fb16855ea79&udm=2&biw=1600&bih=781&sxsrf=ADLYWILh7XUB6hjyOXaNrFUcRf0kkPX7EQ%3A1729839605387&ei=9UEbZ_2eF5ro7_UPqsm2wA8&oq=starter+for+&gs_lp=EgNpbWciDHN0YXJ0ZXIgZm9yICoCCAYyBRAAGIAEMgUQABiABDIFEAAYgAQyBRAAGIAEMgUQABiABDIFEAAYgAQyBRAAGIAEMgUQABiABDIFEAAYgAQyBRAAGIAESJDPAVCACVicoAFwBXgAkAEAmAHxAaAB7BSqAQUwLjcuN7gBAcgBAPgBAZgCD6ACug_CAgQQIxgnwgIEEAAYHsICCBAAGAUYHhgPwgIGEAAYCBgewgIIEAAYCBgKGB7CAgYQABgFGB6YAwCIBgGSBwU1LjUuNaAH4zs&sclient=img it is beter
Hearty congratulations for your effort in presenting videos in the English: Language, you deserve high marks. Your attitude towards learning is brilliant and that goes for your interest in welding, electronics, and languages, and anything else in life.
I am a little worried about the " special component" sparking and the welder arcing through it! as it seems to be installed at a location where it could be replacing the torch itself!! I have to think more about this. Again well done.
don't think about it, just try it,,
,I discovered it by accident after connecting a series of resistors I saw that in a resistor with a defective cover, let the high voltage pass through the skin.
@@zuzuniagrikubanos6473 Great. Is it possible to replace the special component with a resistor and capacitor mounted in series to prevent hf from returning back to the transformer and destroying it?
Thanks
@@GP-zm2kd I fully agree that the special component can be replaced with a capacitor of value that would be a short circuit to the HF and an open circuit to the welding set frequency. I did that without the series resistor included but I fully agree with you a low-value resistor would not do any harm as the HF current is low. It is interesting how displacement current ( capacitors) can be substituted for conduction current ( current through an arc or copper flow ) James Maxwell knew what he was doing when he wrote Curl H= J + dE/dt. as that is what is contained in the welding set with HF start.
Super! That welding road connector is just amazing!👍
Is it possible to connect 8 nano capacitors of 1600 volts to the unification bridge?
Your diagram is so dificult....but i tried to make it...and god bless you also...
If you find this schematic difficult....what can I say... this is one of the easy ones. Good luck with your work.
Thank you for your response. I have all my respect and appreciation for you.❤
great video
your English is perfect and there will be more than a few people making their own Tig welders 🙂
Is it possible to put the high voltage coil in the negative wire with the torch ?
So that the simmer file is in line with the torch
@@MohibAssalem is the same thing..no problem..
@@zuzuniagrikubanos6473
What is the role of the coil connected in series before the Simmer transformer?
@@MohibAssalem chock coil - [ thick copper coil ] with a core... this on the video is very big..i t dasnt need this big.
@@zuzuniagrikubanos6473 This chock coil, is it necessary to connect it to the positive terminal? Or is it important that it be inside the electrical circuit?
@@MohibAssalem i connect alweys on positive terminal, it helps on the scrats start ,,, it is a self-induction componet,,it can work without chock if you dont care about scrats start.
look this = ruclips.net/video/Rblr6qrJ6UM/видео.html no hf starter...
Excellent work! Thanks for sharing your innovations. Your English is also very good. Keep making videos in English!
ops...Congratulation for this precious video.
Awesome. Needed to know if I could manage building a HF start unit for myself. Might diy it instead of shelling out 500$ for an Arc Pig. Thanks.
Thank you sir. This will help for conversion of my old buzzbox.
Thankyou Zuzuni for this great video it was very helpful. Also the 1meg ohm special component was a triumph.
Thanks for showing close up detail..
Eline sağlık komşu :)
İşimizi ucuza yapmalı ve dostlarımıza yardım etmeliyiz.
I didn’t need the English cc. Very good Video. Just curious what is the special component I must have missed something. Or maybe my ability’s are not up to doing something with adding High Frequency to a standard inverter welding machine. Can you tell me more on this subject. Thank You fo the knowledge I’ve gained from this video already
at the minute 4΄00 I explain what it is the special component .
what did you use for the inductor/choke?
it is a core from an old transformer with a thick wire on it... it is a overkill.... a mikrowave transformer core is very ok !!!
Καλή χρόνια με υγεία !!! Τι εξαρτήματα χρειάστηκες για την κατασκευή; Έχω και ‘γω μια παλιά ηλεκτροκολληση και θέλω να την μετατρέψω.... δεν ξέρω αγγλικά....
Ευχαριστω για τις ευχες, τα εξαρτηματα
περιγραφονται στο σχεδιο και αν και ειναι στα αγγλικα το σχεδιο ειναι universal,,δηλ, στο σχεδιο βλεπουμε μετασχηματιστες, διοδους, συνδεσεις, κλπ. για να κανεις
μια κατασκευη πρεπει να καταλαβενεις [διαβαζεις] σχεδιο,, εγω
βλεπω γιαπωνεζους που περιγραφουν σχεδια και δεν καταλαβενω γρι γιαπωνεζικα,,,ομως καταλαβενω [διαβαζω] ηλεκτρονικο σχεδιο,,,
δεν προκειτε απλα για μερικα εξαρτηματα που τα αγοραζεις και τα βαζεις επανω,, προκειτε για ''πατεντα'' που αν δεν ξερεις τι κανεις μπορει να παθεις ατυχημα ηλεκτρισμου που ειναι πολυ επικίνδυνο, οι πληροφοριες που εχω σε αυτα τα βιντεο ειναι υπερ-αρκετες, για καποιον που ξερει τι κανει,,διαφορετικα βρισκεις εναν φιλο σου ηλεκτρονικο και στο φτιαχνει αυτος.
Than for you , i am from 🇱🇰
You my friend are a very smart man. Just a word of caution, be very careful of EMF generated by high frequency arcs. Keep in mind that EMFs generated by high-frequency welding equipment and components, such as inverters and pulsed welding processes, may produce an additional type of EMF, known as radio-frequency (RF) radiation. RF energy radiates through space in the form of wireless waves or digital pulsing. Human blood contains iron and other minerals and there are studies that show how our blood is affected. This is not widely publicized because it will cause negative impact to the welding industry. There is no other technology to weld metal at the moment so it is kept quiet. We have heard of the dangers of RF from mobile phones, RF from HF welding is much more powerful. Stay safe.
what you mention is correct
and certainly human bodies are affected by electromagnetic waves such as cell phone radio or wi fi or satellites and even hv pulses
but the human body regenerates
if we maintain a balance way of life away from toxins, smoking, stress, and poor diet.
I thought RF radiation was non-ionizing - just heats up cell tissue or some such. Can't recall where I read that.
The majority of transformer based welders are stuck at 50-60 hertz depending on your local power supply. There are some wicked expensive Transformer TIG units that have frequency adjustment but I don't know if anyone makes units like that anymore.
And those units have been around for a long time. If there was a serious risk (other then the usual and known risks like welding with a pacemaker) associated with HF produced by inverters and high end transformer TIG machines then wouldn't the industry would revert to "old" transformer welders? Go back to using exotic gas mixes to weld any relatively uncommon metals, colorless stainless welds etc?
@@brianlittleforest631 The profits from the technology are immediate, the consequences and costs are deferred to the future you, the timeline for definitively recognizing the problem far exceeds and preempts the timeline for litigating compensation. Health really cant be compensated financially anyways, so beware.
@Nicole Yenson that was whole lot of typing to tell me nothing.
Be wary . . . why? By what manner and mechnism will HF welding cause harm?
HF inverters units have been around since the 80's and the guys who are retiring out now are still suffering from the usual effects of welding long-term, skin cancer (usually arms) emphysema etc. Seems to me I'm better off investing in the usual PPE - respirators and UV protection rather then wasting the effort to protect myself from a non-existent hazard.
I have one C.C. machine capable of 250 hertz AC and DC pulse adjustment which has got to be a wide wave length - must be upwards of 1000 km wide I don't know exactly how wide of the top of my head. Other machines can do up to 500 hertz.
Since mine is square wave machine the part that uses HF to start the arc is momentary @ 2 Mhertz. Which is about the same wavelength as AM radio. Sorry, but I call B.S.
HF can be fatal for sure. But in the way grabbing a live wire can be fatal.
@@nicoleyensen7062 This looks like the output of google translate? Gibberish! 😅😅😅🤣🤣🤣
That be well and God bless you all, really meant alot , and I subscribe to your channel!
And thanks for the info, I was wondering how they ran two signals on a single circuit , thank you very much, for your time and knowledge, and thanks for the effort to make us understand! Have a great day!
Thank you, excellent video. I would like to know how to make the "simmer coil".
I buy it ready made,,,, but if you want to do it yourself = ruclips.net/video/oRXHI6L-fXA/видео.html
Great stuff man! Thanks a lot!
I have a question 🙂
Would be nice to figure out if it’s possible to make a trigger switch for the Lincoln Electric Speedtec 200C machine? Not HF, just a switch to stop the arc when finished welding.
a very big rele maybe do the trick
SComponent,how it work? It is a short circuit in the ac or dc Wires.?
it is jast a sparc gapp
Thank you for the video! Keep the good way!
fantastic .. good work well done
You have invented something I have been looking for and your video is amazing, thankyou so much. I have an old transformer welder and have been meaning to make an AC TIG from it for a couple of years so I could Weld Aluminum. I bought a HF generator off ebay so I am good to go. I am also interested in a couple of things on the DC version if you do not mind. a) why have you put the "Simmer Coil" and big inductor in the in the ground side. b) what is the unction of the Diacs. May thanks again. PS do you have any videos of you using this to Weld Aluminum
aluminium welding = ruclips.net/video/5V7aUaB0A1A/видео.html and = ruclips.net/video/KbTm4J6Xmpg/видео.html
simmer coil = ruclips.net/video/bjG6Gfjffmk/видео.html
big inductor = is for more soft and continius work
the Diacs = is for extra protection of the diodes from simmer Hi-voltage spaiks
Many thanks. I will let you know how I get on making my one
Perfect for someone who has no idea about electronics
Perfect for someone who DOESN'T WANT TO GIVE 3,000-5,000 euro-dolars for a aluminum tig welding macine,, How about that?
Hello my friend, I congratulate you on your great work, after watching your videos I made a tig machine and it works very well, there is only one detail that I cannot find why it is, it turns out that it consumes a lot of current through the primary of the main transformer when welding, yes I put the output at 200A in the primary, it consumes almost 100A, and that only happens when I use my machine as a tig, has it happened to you? Do you have any contact where I can exchange with you about these wonderful tig welding machines? Greetings from Cuba, Central America and the Caribbean
most likely you have a leak in one of your coils and when you use the high frequency in the tig it makes an arc inside the coil and increases the consumption,,,check or rebuild the special componet whose use is that the high frequency does not affect the coil but is transferred directly to the welding point,, if this does not correct the problem then you need another welding transformer or to locate the leakage by unwinding and re-winding the primary and secondary coils. in this link you can contact and upload a photo if you need more help. = doityourself123.forumgreek.com/t505-topic
Hello, do we need a large current and voltage at the same time with the gas out, to get a good weld, or do we need a large effort with gas only, and why does the user not be electrocuted if there is a current and a large voltage at the same time, please reply and thank you very much
it is about two different current values in the same conductor, one with a few volts and many amperes and one with thousands of volts and zero current,,,but there is always the risk of electric shock...
@@zuzuniagrikubanos6473
👍
very nice
new subscriber because i love how you get a kick out of your "special component" also thank you very much for helping me with this video! i recently bought a tig/mig/plasma welder and didnt realize that it was a DC only. I am hoping that i can some how convert it to AC/DC. so with this video and your other video i hope to have all that and hf start ( which i may have since i dont believe it scratch start) . if you can answer this question for me that will be amazing! in a DC welder does the transformer produce AC current, which is then fed into a full bridge ractifier to get DC ?
thanks for the comments, i love it.
as for your question = an inverter welding works with pulsed rectified voltage and so you can not get AC voltage,,you need either a very sophisticated inverter or a simple welding transformer as I do in the video,,the transformer is cheap and does the job perfectly at AC 50Hz.
@@zuzuniagrikubanos6473 thank you very much!
so just to make sure i have a full understanding. ill need 2 transformers a welding transformer for my ac/dc (adding full bridge rect to get dc) and a smaller transformer for HF ( like from an old crt tv) correct?
again thank you very much i look forward to your videos very informative and to the point!
@@issaproject This is my web page = doityourself123.forumgreek.com/ make a connection and we will analyze all the stages of construction,,send me a personal message or make a post on the topic=doityourself123.forumgreek.com/t505-topic#6957
I need your help, I am total newbie, how would schematic look if there is no rectifier, because I have dc inverter maschine and i want only dc welding.Thank you in advance.
That 'special component' would probably cost atleast $50 bought from a store! Know-how is best anyhow! Why buy when you know how to make!
What is the role of the spark?
Gracias x la información. Buen video
Estimado Zafdeep.
Posiblemente Zuzuni, no pudo agradecer tu comentario por estar muerto.
Su muerte pudo deberse a electrocución, al haberse perforado el aislamiento entre primario y secundario ( y/o gabinete) del transformador 220/50 VCA. Aislamiento típicamente pensado para tolerar un par de miles de voltios.
Especialmente, usar la configuración que definió como DC, es la más grave.
El aislamiento se puede ir degradando lentamente, hasta que en algún momento el nivel de carbonización es lo suficientemente alto para electrocutarte.
El dispositivo tiene que tener el apropiado aislamiento y supresores de descarga, para evitar el tipo de problemas descrito previamente.
Saludos.
خیلی خیلی ممنون بسیار توضیحات کاملی بود
ruclips.net/video/ti6RkIbA93o/видео.html
"Hello, very much, thank you, Master, please introduce the same as tg35C60, thanks"
anything that withstands 35+ amps does the job
El positivo va como masa en la base como la sold electrica y la parte que agarraria el electrodo es negativo el centro bien el mapa.bien claro gracias sr Arg
in tig we put the positive in grounding.. in stick we put the Negative in grounding.
thank you, for tutorian zuzuni
Hi, Mr Zuzuni, sorry by ask you but what ´s bridge rectifier diode´s value? 10nF or more? Regards from Brazil.
is a diode ..not a capacitor to have nF Value.
what are the approximate ratings for the high voltage caps?
15κV
On the 'SC'
Does the core of the rod get used as one terminal then?
it get used as a spark bridge that allows hv to pass and the welding current not to pass.
Will hf pass through the dc inverter electronic component? Then fry up the component?
Where u get high frequency board ebay? which one? . so this box is or is not connected to the other welder? .. im confused why you have another giant welding transformer in the box if you connected the other welding box to this gray box.?
the gray box is a rectifier for DC Tig for AC i conect direct to welding box,, the big transformer in the gray box is a filter chok with only one coil. For the hf board I do not advertise, take whichever you like.
@@zuzuniagrikubanos6473 thanks i understand. Thats a huge choke
👍👏
Hi, I dont know what is a simmer coil. I cant find here in Argentina. Can you tell me more about it? Thanks.
Cutting Machine Arc Starter Coil Full Copper = www.aliexpress.com/wholesale?catId=0&initiative_id=SB_20220727103219&origin=y&SearchText=Cutting+Machine+Arc+Starter+Coil+Full+Copper&spm=a2g0o.detail.1000002.0
can we really weld aluminium at only 60 hertz ?
of course.. what is important is that there is an AC arc and heat capable of melting the aluminum
Mine heats up the resistor a lot. it came to loosen the tin solder on the board. what can i do to solve this problem?
use an economy neon lamp driver to drive the fly-back transformer = ruclips.net/video/TX8rxBenZPk/видео.html
thanks you teacher.♥
what is the voltage rating of diac and how many are used?
5 to 10 diac in series.. 20v rating
Woww
What is the link to where you describe the special component SCS? What voltage is the diac and what kind and value for the capacitors across the bridge, the part number for the High current diodes and how many are used (for example if many in parallel), and how to construct the huge high amps chock (i.e. how many henries) for the DC side TIG circuit? Please provide this info either in the description or answer me directly, Thanks.
χρηστο....στο βιντεο τα περιγραφω μια χαρα,, τωρα αν θες περισσοτερες λεπτομεριες φτιαξτο και βρεςτα ολα αυτα,,, εγω τι να πω που τα φτιαχνω και δεν ρωταω κανεναν ?? αν εχεις λιγες γνωσεις μια χαρα θα το φτιαξεις,,αλλιως αστο-παρατατο...
@@zuzuniagrikubanos6473 Signomi min thimonnis apla mia aporeia eixa gia ta exartimata. alla se afto to video einai sxedon se block diagram. Apla mporouses na me parapepsis sto timestamp pou mas fotizei ti telos panton einai afto to SC (mipos einai snabber?)
@@christosmakariou4574 το SC το κατασκευαζω ζωντανα στο βιντεο απο ενα ηλεκτροδιο και λιγο συρμα,, αν δεις προσεκτικα το βιντεο θα το δεις, προκειτε για ενα sparc-gap ουσιαστικα και οχι snubber που μεταφερει απευθηας την υψηλη ταση στην γειωση.
job is great.. can you show step by step setup this circuit i'm very interesting
You can not know how to read an electronic drawing ??[schematic on video]....ask a friend to help you
@@zuzuniagrikubanos6473 i have just tig dc mode , not have Ac mode my mechanic weld. i must be try what you sharing. tq so much..
Great. Is it possible to replace the special component with a resistor and capacitor mounted in series to prevent hf from returning back to the transformer and destroying it?
Thanks
Try it and tell me the result.
Do not forget to tell me the value of the resistance in watts and ohms,And the value of the capacitor in volts and farads.
thanks in advance.
@@zuzuniagrikubanos6473
Thanks for your attention. I am thinking of a filter consisting of an 8 Ohm 25 W resistor in series with a 12 microfarad 250 V capacitor. This filter should protect the transformer upstream of the filter. However your solution is very cheap and this is good. Thanks bro.
Do it work?
Aluminium weld?
ruclips.net/video/KbTm4J6Xmpg/видео.html
Do you espeak in spanish
@@edgarmauricioromero6852 no i dont but the shematics on my video is universal.
Can I use DC Tig and convert to AC? I have older welders that are ac.
use the older ones
@@zuzuniagrikubanos6473 use the older ones to what? Thanks bub
I have a PS4. Where the hard drive connects to motherboard, the solder on the connection at the motherboard (where the hard drive connects to motherboard) it is cracked up n is messing up. Can I trace those cracked solder leads n add jumper wires to where they connect elsewhere on the motherboard? Thank you.
I am capable of doing it, are you capable of doing it?
@@zuzuniagrikubanos6473 I'm not sure yet as I don't know whether there are visible leads to the end of circuit. Besides I'm so darn busy right this moment. I ended up getting covid a month ago and it really done me in so I got behind on my personal work. I'm getting much better now but it's taking me time. Plus we gotta big family. I will look. Do you have Facebook? If so you can add me. Chad Moyer. Thank you bub n remember I'm in USA....Ohio so time is different. Thank you
@@chadmoyer1453 i dont have Facebook, i getting covid a month ago too,,,, it was not a big deal,, 4 days of fever and 4 days of cough, I did not take any medicine nor a vaccine.
have fun
and everything will be done.
@@zuzuniagrikubanos6473 be alright if you did for communication purposes. It's really good for that. Plus you can get ur channel out there more. Ive shared a few of your videos. But covid messed me up. I still have small issues; plus I have skitzo n bipolar and a blowed out hip. After I healed up some from covid, it sat in my hip for a few weeks. I'm better now thank God. I can run n work even more now but I've got a lot to catch up on. Therefore if I don't communicate much now it's ok because I really enjoy electronics. I mainly have residential grade electrical skills, but picked up some industrial/commercial (3-phase…switches) as well as low voltage. But electronics is not my area right now to be any confident in, but having a friend surely helps... thank God.
@@chadmoyer1453 If you like electronics the best way to learn - find out is to buy a cheap oscilloscope, a cheap power supply and a cheap multimeter and
start to make this = talkingelectronics.com/projects/50%20-%20555%20Circuits/50%20-%20555%20Circuits.html?=true&width=100%&height=100%
once you make a few circuits you will understand many things.
in the link I show you it has low voltage circuits that are relatively harmless and have a pleasant and useful effect.
At the same time you will discover that many of our fellow human beings deal with electronic constructions as a hobby and soon you will meet many friends who like the same thing.
but if you do not use a soldering gun,, with the theory alone you will not achieve anything.
I am not an electronic ,, I am just a carpenter who likes constructions and new knowledge ,, a hobbyist you can say.
I will help you as much as I can but as you understand you are the one who will make a construction from alpha to omega.
Zuzuni...Good night...excuse me my inglish isnt so good ...your work and vídeo can help me very much.But would be possible you send me the value of all components such diods,capacitors and so on.I will get and thankful for this help. Your edres is not available to me.Thanks.best regards
.
Hello....ops...could you send me the value this all components...capacitors,diods...etc....thanks.
Very good... How about SC /Special componen Sir? Thanks
on 5.5min of the video.........sc
👍👍
What is the special component
did you see the video? or not ?
How to work arc (mma) to tig ,mig welding curcuit diagram.plese gime me.
schematic on video
hi.., what is the power of the simmer coil?
ruclips.net/video/bjG6Gfjffmk/видео.html on 19'00min
thankyou.👍
This „special component” is basically a voltage dependent resistor? I don't understand the role of the capacitors and the diacs on the diode bridge. The purpose of the „special component”, and the capacitors, and the diacs together, is to protect the welder's diode bridge from the high voltage? Please give me a detailed explanation. You can use your language, if it makes easier to explain, i can translate it.
the capacitors, and the diacs together, is to protect the welder's diode bridge from the high voltage
The purpose of the „special component”, is to connect the ground and the electrode to simmer coil.
If I understand it correctly the SC is a spark gap. The first inductor on the DC version does not conduct high frequencies but can pass the 40v for the welding current. This way you can apply a high voltage between the tool and ground without the HV getting shorted out by the thick welding wire. Because the first inductor is effectively removed from the circuit as far as the high voltage is concerned you need a device to close the circuit for the high voltage but not short out the weld current. The spark gap allows this.
Hmm or perhaps its just a HV cap to the same effect?
@@Kezat if something works dont fix it
@@zuzuniagrikubanos6473 I agree, my intent was to understand how it works, not to replace anything. Best wishes.
What is the marked sc on the scheme?
special componet = ruclips.net/video/WToNfDHsde8/видео.html
How much value for dioda and capacitor? Thank you
diode = www.amazon.nl/Eastar-ZP20A-Prestaties-Silicium-gelijkrichter/dp/B07B8B6NK1
hv capacitor = www.amazon.com/20000V-470PF-Voltage-Ceramic-Capacitors/dp/B074S7774H
@@zuzuniagrikubanos6473 thank you very much ..
Hey thanks so much for doing this video! Thanks for specifying the capacitors and diodes in another comment as well. I've got all the components ready now. Just before I put it together can you please confirm the very last component you drew. Is it a pair of opposing diodes, or something else? At 27:06.
@@vardfriki7274it is a diac ,, 4 diacs in series conect,, chek on 7.30
thank you....
Thank you
Μάστορα Πατρινός είσαι γιατί σε είδα απο το φωντο της γεφυρας.
αυτά είναι..... και να θέλεις να κρυφτείς την σήμερον ημέραν.........
@@zuzuniagrikubanos6473 και εγω θέλω να βρεθούμε εχω ενα κύκλωμα που πιστεύω θα σου λύσει τα χέρια με το EN 555 με είσοδο 12 vdc και βγάζει 35.000 v με διακοπτομενη είσοδο. Εγω απο αγυια είμαι
@@zuzuniagrikubanos6473 πολλές καλημέρες
Κανωνισε να βρεθούμε εχω και εγω ηλεκτροκατασκευαστικες ανοισυχιες
@@κωνσταντινοςκαραμπετσος Εδω μπορεις να με βρεις = doityourself123.forumgreek.com/ συνδεσου και στηλε μου μήνυμα.
how can i send you private message?
here = doityourself123.forumgreek.com/
@@zuzuniagrikubanos6473may i know your email adressed?
@@erwinerwanto1064 what do you want ?? whatever you want here = doityourself123.forumgreek.com/
@@zuzuniagrikubanos6473 going to support your channel, any paypal?
@@zuzuniagrikubanos6473 pls dont offence 🙏
It doesn't work as real HF starter tig welder... half time you perform a lift start.. maybe you should increase the voltage? Clearly you are welding on dirty surfaces and maybe this is the reason why your arc's not start
it is only a demo... in dc mast have sharp point on tungsten and clear surface.. in ac is d'ont mater... its start watever surface or tungsten conticion
the ark starts from heet and a sharp point heets esyer like here= ruclips.net/video/Rblr6qrJ6UM/видео.html
@@zuzuniagrikubanos6473 Ok ok you convinced me! I never weld with tig machine and I always ask my self if is better to buy a good MMA welder for a reasonable price (lincoln for example) amd transform it in HF tig with a circuit like yours (thanks for it) or buy directly a mediocre tig welder for chip price.
@@giacomoc.6100 there is no chiper than this = ruclips.net/video/KbTm4J6Xmpg/видео.html aluminium tig welding with old chip transformer welder
Thirty minutes to tell you nothing, what he has shown is wrong! What on earth is a "special component"? 25A x 220v= 5.5Kw, 40 x 200=8Kw, getting more out of the transformer than he's putting in, magic! The high frequency cct is on the torch cct not in the return. What that DIAC ( DIACS, by the way are signal level components used to trigger triacs) is supposed to do is anyone's guess? There's no date on this post so I must assume it's an April fools joke...🤣🤣🤣🤣🤣
Γεια σου ικαρε σαββιδη με τα ωραια σου.... !!!!! παρεπιπτοντως σε ολο τον κοσμο μετα τα βιντεο μου φτιαχνονται διαρκως τετεια μηχανηματα.. πχ = ruclips.net/video/EUuWTZwcvSI/видео.html&lc=Ugwufg4JdpUMAEKf6Gt4AaABAg
لم افهم H f ماهي
If you don't understand what H f is don't bother.......don't write in Arabic to a Greek,,, make the effort and write in English so that someone might want to help you, to make it easy for them
@@zuzuniagrikubanos6473Thank you for your response. I am an Arab from Algeria. I would like to help you. Your mother, where can I find the HF and SC parts?
@@yazidfryazid5039 ruclips.net/video/bjG6Gfjffmk/видео.html
Please, what is the component (SC) in the circuit? I did not understand it?
@@yazidfryazid5039 from 4.00 to 8.00 minute of the video explane what is the sc [special componet] is.
FAKE !!👊👊