How to adjust the welding machine output current (Working perfectly)
HTML-код
- Опубликовано: 27 авг 2024
- #welding machine #currentadjustment #outputcurrent
$2 for 1-8 Layer PCBs, get JLCPCB $54 new user coupons jlcpcb.com/RHS
Hello...
In this video, I made a circuit that can adjust the output current for the machine I showed in my "Arc Boiling Machine" video, which attracted a lot of attention. I had set up a circuit during the construction of the machine. In fact, the circuit I made worked very stable and never malfunctioned. However, I guess it was a bit confusing because I did it with the method called "space assembly". Many viewers reported that they could not understand the wiring and assembly of the circuit in the machine. That's why I decided to make a new circuit that is accessible to everyone.
I had the PCB production done by JLCPCB company and I was very satisfied with the result. That's why I recommend it to you. You can download the circuit diagram and the necessary file for PCB production (GERBER) from the links below.
8 triacs can be connected to the circuit. As the number of connected triacs increases, the power of the circuit increases. For example, when using 4 8 Ampere triacs, a total of 32 Ampere current resistance is obtained. In this case, the power of the circuit is approximately 220x32=7000 Watt at 220V mains voltage. Although this value may seem very high, it is necessary to reduce the probability of failure for 2 microwave oven transformers. This power value can be considered as 110x32=3500 Watt in places with 110V mains voltage. Since I get a lot of questions about this, let me try to explain a little:
In places with a mains voltage of 110V, the welding machine will draw more current from the input in order to obtain the power of about 2000 Watts it needs. In this case, although 4 triacs have a total power of 3500 Watts, I recommend that those who use 110V voltage connect 6 triacs as there may be a risk. In this way, the probability of malfunction will be minimized.
The elements used in the circuit are materials that are chosen very affordable and can be found everywhere.
Input and output sockets have been selected as 4-pin to increase mechanical strength and current carrying capacity. Those who use 2 transformers and have 220V mains voltage like me can use the 2 pins in the middle. In places with 110V, since 2 times the current will be drawn, 4 pins should be considered as 2 pins, right and left, and if necessary, 2 wires should be connected. In this way, the current-carrying cable cross-section is increased.
You can download the PCB production file of the circuit below and upload it to the website of JLCBCB and have it produced.
I hope my video was helpful and you liked it.
Do not forget to SUBSCRIBE to my channel, press the LIKE button and activate the RING notifications to be notified of my future videos.
PCB PRODUCTION FILES (GERBER):
drive.google.c...
CIRCUIT DIAGRAM:
drive.google.c...
WELDING MACHINE CONSTRUCTION VIDEO:
• DIY Welding Machine / ...
WELDING MACHINE AC - DC CONVERSION VIDEO:
• AC to DC for Welding M...
This project is very good!
Thank you so much 👍
안녕😊 오랜만이네요 팔방미인 입니다 기다린보람이 있어요 오늘도 잘보고 갑니다👍👍👍👍👍👍👍다음을 또 기다릴께요 👏👏👏👏
매우 감사합니다. 영상 자주 올리도록 노력할게요👍👍👍
Tudo muito bem construido, vou fazer uma igual para meu uso, já estou comprando os materiais e só estou com dificuldade em encontrar fio 4mm com revestimento em silicone. Parabéns pelo projeto e parabéns pela bela construção!
Muito obrigado. Estou feliz que você gostou. Para cabos isolados de silicone, procure uma loja grande que venda apenas suprimentos elétricos. Pode ser difícil encontrar curtas-metragens online. Esses cabos geralmente são utilizados na instalação interna de itens como resistências elétricas. Obrigado novamente...
To improve welding, it would be advisable to connect an inductor in series behind the rectifier.
Hello. I got a lot of advice on this. I want to try but I'm not sure what coil to use
I had just made a post addressing this. Hope the info helps!
Murat hocam tebrik ederim.
Çok teşekkür ederim Levent hocam 👍
I appreciate your skill.happy.
Thank you very much.
Vidéo très intéressante et surtout c'est très bien expliqué 👍
Merci. Je suis content que tu l'aimes. J'ai fait cette vidéo car il y avait un problème de compréhension avec le circuit que j'avais fait avant. J'ai essayé d'être aussi descriptif que possible.
Helal olsun murat abi ❤❤
Really like your video man! Gonna try the scr control function on induction heater. Guess it is going to work well. Thanks!1
I thank you too. Greetings from Turkey 👍
very good!
Thank you so much 👍
akan saya coba 👍
👍👍👍
Hey my man, another good video. One of these days id like to try out your triac configurarion. Ive built this welder and used an scr for my power regularion.
Idk if you remrmber but he spoke through comments about adding a dc choke/coil filter in the comments on the other videos of this welder. I would like to share with you what i had done regarding this. I used 2 mots like you did for my welder, i took 2 more mot cores of similar size and welded them together face ro face to make one long transformer El configuration. Wound it as tightly, neatly and solidly as i could with 10 ga silicone wire, the same wire i use on my welding tranformers. I then put it in the positive line coming off the rectifier, before the capacitor. And so far it has been working quite well!
Now i want to explain that instead of running stick i tried to fashion a wire feed motor for my welder to ise as a flux core or mig, i failed at that so i bought a cheap wire feed motor and power it iff an led 240ac to 12vdv converter. Running flux core through my machine works very very well and thebaddition of the choke makes it 10x smoother. Now i need to note that it seems i had some current loss due to the limitations of the transformer but am still welding thru 1/8 to 1/2 inch just fine with 0.030 wire. This is why i wanted to add the choke. I found out however thatbif i were to run stick, with the filter choke, id need to remove the capacitor. So idk if you really want to explore that with this project or not. Just some info to try n help. I would not have my homemade awesome little buzz box if i had not found your channel my freind. Keep up the good work and have fun!
Hello. We've had conversations about the coil, but I still haven't been able to. You did and you succeeded. Congratulations. If you send me your detailed photos and schematic information, I can try and even make a video when possible so that other viewers can benefit. I'll add your name to the video as a quote. Thank you for your return.
@ hey, well i am in the process of rebuilding the box to house everything, takes time because i work alot of hours. I honestly still dont know the calcularions of chokes or the specs of this one specifically nor do i keep any schematics. Online i have found several web pages with detailed information on filtering dc though, qnd have followed the schematic for an lc filter configuration. There are some detailed points i would like to share tho, if you or anyone decides to try this on their own. You can use tha capacitor before the choke BUT you will need at least a 100amp diode between the cap and choke, the flyback from the choke will blow the cap unless it is monsterous, it blew my 125v 4700uf cap. I use it choke 1st then cap from the rectifier. I use a 1600v 200amp full bridge rectifier in mine so that device can handle the flyback, or at least seems ro be able to so far. Once im finnished with the new box i will post outputs n such but as far as pocs, idk how to post those lol. I only fairly recently started playing with yt
Hi. I understand you. You can send the videos or photos you want to share to the e-mail address muratguney67@gmail.com
Hola te escribo voy a intentar hacer este tu proyecto mejorado y con tus conocimientos y asesoría para en fin hacerlo viable.. Y seguro. Cuento con su apoyo
@MuratGuney once again great work. Exist another solution without to modified the voltage sinusoidal form in primary coil. Idea is to saturated the core from exterior columns, using two coils connected at c.c. voltage regulator. Using c.c. voltage to this coil you can control how from alternate flux can pass through this columns. Ideal construction is with primary and secondary a.c coils to exterior columns and coil connected to c.c. voltage in central column.
Hello. Firstly, thank you. However, I did not understand how I could adjust it without disturbing the sinus form. What I did is an easy and cheap method. However, it makes adjustments by chopping the sine wave. It works, but I can admit it's not perfect.
@ Your solution used is OK, but I wish to remember that also are other solutions. Theoretically, with an dc coil you can add an non alternating flux in the core and remain available less (equivalent section) for alternating flux and in this manner is moved the point of function on plane characteristic (in saturation zone) V/T (voltage/induction) of the core.I think, with two magnets, for example: one with N on the left column and another with S on the right column, you can see some difference, of course the difference depends on how strong the magnets are.
Murat güney gerçekten eline sağlık uzun zamandır kaynak makinesine güncelleme videosunu bekliyordum. Tavsiye olarak bir ampermetŕe bağlasan çok güzel olur teşekkürler
Ben de teşekkür ederim. Ampermetre güzel olur ancak bu sistemde ampermetre sadece kaynak esnasında akımı gösterir.
@ seninle nasıl konuşabilirim iletişim için
@@ademozturk3547 Merhaba. Benimle buradan veya muratguney67@gmail.com e-posta adresinden iletişim kurabilirsiniz. Telefon numaramı paylaşmıyorum. Beni anlayacaginiza eminim. Teşekkürler
Ustam eline sağlık güzel olmuş 👍
Excelente, se puede sustituir por 4 triac bta 41-600
gracias por su respuesta eres un genio
Gracias a ti también. Saludos desde Turquía 👍
You need three transformers because most welders use 1/8th inch electrodes.
Three or more in series is better. Giving you the most stable arc ever.
Able to turn rutile rods into deeper penetration rods.
Overall, decent video.
Thanks. I have also built machines with 3 transformers and 4 transformers. I made this machine with 2 transformers to make it a little lighter. I think it wasn't bad.
Great job bro but I hope you add a lcd screen and ampere controller
Thank you very much. I am glad you like it. Adding an LCD screen is a great idea. I can do this with ease, but most viewers can't. A programmed microcontroller is required.
عمل رائع انا عملت 6 محولات ماذا عن عدد الترياك كم استعمل
بادئ ذي بدء ، شكرا لك ، إذا كان الجهد الكهربائي 220 فولت ، يجب عليك استخدام ما لا يقل عن 8 التيرستورات. يمكنك العثور على مقطع فيديو يوضح كيفية إنشاء دائرة التعتيم على قناتي. يمكنك أيضًا العثور على ملفات PCB في قسم الوصف بالفيديو.
2 trafolu kaynak makinesi videonda yaptığın dimmer devresiyle bu devre arasında bir fark varmı sence yaptığım zaman hangi devreyi yapayım
Merhaba. Devreler aynı aslında. Ancak diğer videoda devrenin yapilisj anlasilamadigi için bu videoyu hazırladım. Burada da bütün triyaklar paralel bağlı. Ayrıca 110V gerilim kullanan yerlerde daha fazla triyak kullanılması gerektiği için kart üzerine 8 adet triyak bağlanabilecek şekilde yaptım. Türkiye için 4 triyak yeterlidir
@ teşekkür ederim
Muito bom! Perfeito ❤
👍👍👍
maestro buenas tardes en mi pais la corriente es 220 v tengo un dimmer de 4000 watts con un triac bta 41600b mi pregunta es le puedo poner 4 triacs del mismo numero
👍👍👍👍👍super
Thank you so much.
The machine performance is quite acceptable. The operator needs instruction and much practice.
Hello. Firstly, thank you. I agree with you. Definitely need training on welding 😃
Isn't the capacitor that remains charged dangerous?
Hi. After each welding process, a voltage of around 60V remains on the capacitor. This is destroyed during the source short circuit. However, after the work with the device is completed, the last remaining voltage. It takes a long time to discharge. It is not a value that could be dangerous. However, if the ends touch each other close to the eye, an arc will occur and may damage the eye.
Sayın Hocam,şu potu çift yapsan da 3 digit göstergeli olsa daha şık olmaz mı ?Malzemeleri hazırladım.Versiyon 3 için yeni videonuzu bekliyorum.Saygılarımla...
Merhaba Agah bey. Potu çift yapmaya gerek yok aslında. Çıkış zaten DC olduğu için voltmetre bağlanabilir. Ampermetre de kullanabilirsiniz ancak akım değeri sadece kaynak sırasında okunabilir. Ben kutuyu küçük yaptığım için gerçekten alan sorunum var. Gozterge eklemem için kutunun alüminyum bölümlerini uzatmam gerekiyor. Bu sıra bu konuda çalışabilecek zaman bulabileceğimi sanmıyorum. Yakında makinemi kullanarak balkon korkulukları yapmaya çalışacağım. Yani başka şeylere zaman ayırmam gerekiyor. Lütfen kusura bakmayın. Selamlar 👍
90 A is less for 3.25 mm electrode. You should use only 2 mm electrode. Rutil 6013.
Hello. There is no problem with Melting the 3.25 electrode. It melts pretty well. To tell the truth, I think there was a problem with the current measurement. Because even though the output is DC, I couldn't make a good measurement when I took the meter to DC stage. Because when a load is connected to the output, full DC output cannot be obtained. As a result of the rectification, a 100Hz full-wave rectification signal is obtained. Therefore, I may have made a mistake during the measurement with the ammeter. As you can see in the video, a very smooth welding process is obtained.
Hola amigo un saludo desde Venezuela.!! Una pregunta podré usar está máquina sin ponerle ese sircuito impreso.
Hola. Puede usarlo, pero no puede ajustar la corriente. En este caso, si usa electrodos delgados como 2 mm, la corriente es demasiado. Pero puedes quemar electrones como 2.5 o 3.25. Esto también debe agregarse. Si la parte soldada es demasiado delgada, el exceso de corriente puede perforar la parte. Es mejor que construyas la máquina sin el circuito. Dependiendo de la situación, puede agregar el circuito más tarde. Saludos desde Turquía 👍
Salut , il y'a une loi dans le soudage, c'est que chaque 1mm d'épaisseur soit dans la tôle ou la baguette équivalent à 40 Ampère, t'as 2mm donc 80 ampères, t'as 3mm donc 120 ampères, mon frère Murat bonne continuation
Bonjour. Je pense que vous parlez de l'épaisseur du matériau à souder. Merci pour l'information. Je pense que je me suis trompé sur les mesures que j'ai faites. Parce que comme vous pouvez le voir, l'image de soudage réalisée avec l'électrode 3.25 est très belle. Si le courant est insuffisant, l'électrode ne fondra pas correctement de cette manière. J'attribue la raison de cette erreur au fait que j'ai converti la sortie en courant continu. L'ampèremètre ne peut pas mesurer correctement car le condensateur à l'intérieur de la machine est en décharge continue pendant le soudage.
Здравствуйте! Мурат хотел спросить, а если на трансформатор от микроволновки намотать алюминиевый провод с медным покрытием без изоляции с сечением 4мм! И подключить к сети 220В. Что будет просто боюсь подключать к сети 220В. Вдруг замкнет или бабахнет точнее взорветься? Просто алюминиевый провод немного задевает первичную обмотку.
Привет. Вы серьезно относитесь к использованию неизолированного провода? В этом случае происходит полное короткое замыкание. Скорее всего предохранитель сгорит. Если нет, то еще хуже... трансформатор сильно греется и первичная обмотка может сгореть. Определенно нет.
Podrá enviarme el diagrama de el regulador, por favor
Quiero hacer ese circuito, gracias
Hola. Puedes encontrar todos los diagramas necesarios en la sección de descripción.
Can you make an AC welding machine
Hello. I already have 2 AC welding machines on my channel. I recommend you to take a look at my videos. My machine with 2 transformers, which is currently DC, was also giving AC output when it was first made.
Can i use triac too switch it on and off just like the solid state relay ?
Of course you can use it. Where do you intend to use
Ustam eline emeğine sağlık bu yaptığın devre ile 4000w dimmer devresi arasında fark varmı
Merhaba. Öncelikle teşekkür ederim. Aslında fark yok ama bu devreye daha fazla triyak bağlayarak daha güçlü hale getirilebilir. Ayrıca kaynak makinesi videosunda dimmer devresine yaptığım işlemi herkes anlayamadı diye düşündüm ve bu devreyi yaptım.
Great!
Is it possible to TIG convert it?
Thanks. I will try this when I have the opportunity, but I don't have the necessary materials at the moment.
ألة اللحام الخاص بك هل تشتغل 220 فولت
نعم. هنا أيضًا جهد التيار الكهربائي هو 220 فولت.
Murat bey parça temin ettiğim elektronikci 30 v diac elinde olmadığı için baglamasanda olur dedi sorun olurmu?
Selam. Diac bağlamadan olmaz. Siz ellerinde olan diac varsa alın ve kullanın. Diac devrede bulunan triyaklarin iletime geçme zamanlarının değişimi için gerekli
@ murat bey bütün parcalar tamam. 100nf kapasitörun v değeri kac olmalıdır?
Мурат, судя по сварочным швам, у аппарата не хватает выходного напряжения!! Напряжение холостого хода нужно от 55 вольт и выше!!
Привет. Выход постоянного тока составляет около 60 В. Проблем с возникновением дуги нет, но было бы лучше, если бы напряжение было выше. Спасибо за интерес 👍
Does it have to be 220v? I'm in the states and we 110v here.
Hello. If you are asking about this circuit, there is no problem. So you can also use it with 110V. However, since more current will be drawn from the network at 110V voltage, it would be better to connect 8 triacs to the circuit. If your question is about the welding machine... the answer is yes. In other words, you can make the same welding machine and use it at 110V voltage.
👏👏👏
Teşekkürler 👍
Can i use class 220 and class 250 transformer together for this
Hello. I think the values you are talking about are voltage values. This circuit is voltage independent up to 500V. So you can use. If the number of transformers you will connect is 2, you should use 4 triacs as I did, and if the number of transformers is 4, you should use 8 triacs.
Thank u for u r reply brother
Thank you too 👍
buenas tardes mi otra pregunta es al dimmer de 4000 watts 220v con el triac bta41600b le puedo poner 4 triacs bt 137600e
Si vas a conectar 4 BT137, te recomiendo conectar el otro triac. Sería mejor si los elementos a conectar en paralelo fueran idénticos. Creo que puedes usarlo con tu circuito existente y si tienes problemas, puedes conectar 4 BT137. Si el circuito del atenuador se estropea, el triac y el diac (generalmente un elemento de circuito azul de 2 pines) fallarán. Cuando los reemplace y repare cualquier rotura en el circuito, su circuito funcionará.
جميل جدا... كم قيم الاي جي بي تي
مرحبًا. أولا شكرا لك. العنصر الذي أستخدمه هو BT137 triac. المستندات الضرورية متوفرة في قسم الوصف.
Usta bu en fazla kaç amper veriyor
Merhaba. Bu devrede 8 adete kadar triyak takılabilir. Bu durumda 8A lik 8 triyak paralel baglandiginda 64A olur. Tabi bu kaynak makinesinin giriş tarafı için. Yani 220x64=14000W güç olur. Çıkış tarafı için en azından 250A lik makinede kullanılabilir. Açıklama bölümünde biraz daha ayrıntılı bilgi bulabilirsiniz.
I have online on your PCB board where do u buy.
Hello. You can find the necessary files for PCB production in the description section. You can place an order by uploading the files to the website of the jlcpcb company.
sr buenas noches soy peruano quisiera saber si el dimmer anterior con los triacs le funciono bien y quiero saber si el nuevo regulador de voltaje hace lo mismo por que le puse un dimmer de 4000 wats y mucho quemaba el fusible. digame al dimmer de 4000 le puedo poner 4 triacs de bta41600b o le puedo poner 4 triacs bt 137600e .espero su respuesta es un genio le pregunto eso por que no se como comprar los protoboard que ud usa
Hola. Si el voltaje de su red es de 110 V, debe usar un circuito de atenuación más potente. Si es 220V, puedes usar 4000W... Si no hay problema con las conexiones y el fusible no se funde cuando energizas los transformadores sin instalar un atenuador, vuelve a conectar el atenuador. Sin embargo, si el fusible se funde constantemente, es posible que el circuito que estás utilizando esté defectuoso. Para entender esto, puedes mirar el triac en el circuito con un multímetro. Si va a utilizar el mismo circuito, reemplace el elemento diac junto con el triac en el circuito. bta41600b es un triac de 40A y se puede utilizar. Estoy usando 4 BT137. El circuito que ves en este video funciona igual que el circuito que hice antes. Como ventaja, no hay desorden de cables y se pueden conectar más triacs.
Would be better with talking
Hello. You may be right about this, but even if I speak, I speak Turkish. Generally my viewers are from other countries. That's why I prefer to put subtitles. Thank you for your attention
👍
Thank you 👍
@ sevgili dostum ben de turkum :)
@@tvbox8478 İsmi böyle görünce anlayamadım. Daha önce de yazmış olabilirsiniz. Kusura bakmayın. Selamlarımla...
Skema please?
Hi. You can find Sema and other information in the description section.
Hai murath . Is it ok to use swg 10 winding core insted of 4 sbqm copper cable and how many turns should i do for one secondary
Hello. If you use AWG10 cable, I recommend using 3 transformers. otherwise the Voltage will be low. You should wind the transformers as much as you can. It will probably fit between 13 - 15 turns.
Hi Dear Mr. Murat Güney!
I would like to ask about that ruclips.net/video/WrngBsmGQtQ/видео.html
Triac regulator connection.
- Have you installed the converter between the output of the AC secondary side AC 40V and the rectifier bridge or somewhere else???
I would friendly to hear your kind reply.
Hello. I put the dimmer circuit in this video on the input side, between the primary winding and the mains voltage. A circuit like this would not be suitable for output because the output current is too high.
👍👏👏
👍👍👍