thx for the video, I have also bought the same hop up chamber and had some difficulties with the installation, and your tips were the key to fix the problems. Do you think that Maxx Model chamber is the best possible option for SRS hop up?
Thanks for your comments. I believe it is great! You get very good results with the stock one also if your seal is 100% but it's very difficult to make any changes in game. So yes I stick with the Maxx!
it is better than stock ? I have PDI 6.01 inner barrel. Do you have R-Hop installed > ? How about reloading ( is the cylinder head can tur your hop up setting wheel? that was problem in fast hop for me )
Stock is also very good. Stock is for sure better than fast hop. I use edgi barrel with snipetor 75° rhop. I don't have any issues with cylinder head changing my setting!
way better than stock. if you are running a silverback I wouldnt recommend an ultra tightbore...the gun is overvolumed...get a 6.03 minimum. As for reloading, the cylinder head never touches the hop wheel. and dont bother with Rhop...waste of time. Get the maple leaf Mr Hop GBB or AEG model hop rubbers, or you can use the autobot. the MR hop 60 degree decreased my groupings at 100ft from 4 inches down to 2 inches. 60 or 70 degree will work well. as close to rhop as you can get in a standard hop rubber without the headache and expense.
Hi! I have a question to ask you. When I mount the Hop-up chamber, I have a loss of tightness. I go back up and I see that my SBA gasket is cut above the nub window. already two fucking joints in the air knowing that I'm careful. How to avoid this on a 3rd joint?
Obrigado! Melhor explicação que achei no RUclips!!!
thank you very much, it help s me a lot!
Really appreciated
Casual tank just starts up halfway though the video 😄.
Ótimo vídeo, parabéns
put the other end on the hop rubber first, youll find its much easier.
Holy smokes u ain't messing around with the parts lol raw force will make it work ;)
thx for the video, I have also bought the same hop up chamber and had some difficulties with the installation, and your tips were the key to fix the problems. Do you think that Maxx Model chamber is the best possible option for SRS hop up?
Thanks for your comments. I believe it is great! You get very good results with the stock one also if your seal is 100% but it's very difficult to make any changes in game. So yes I stick with the Maxx!
Καταπληκτικό
Να είσαι καλά φίλε.
it is better than stock ? I have PDI 6.01 inner barrel. Do you have R-Hop installed > ? How about reloading ( is the cylinder head can tur your hop up setting wheel? that was problem in fast hop for me )
Stock is also very good. Stock is for sure better than fast hop. I use edgi barrel with snipetor 75° rhop. I don't have any issues with cylinder head changing my setting!
@@Saboter hmmm... Maybe i should try IT.
way better than stock. if you are running a silverback I wouldnt recommend an ultra tightbore...the gun is overvolumed...get a 6.03 minimum. As for reloading, the cylinder head never touches the hop wheel. and dont bother with Rhop...waste of time. Get the maple leaf Mr Hop GBB or AEG model hop rubbers, or you can use the autobot. the MR hop 60 degree decreased my groupings at 100ft from 4 inches down to 2 inches. 60 or 70 degree will work well. as close to rhop as you can get in a standard hop rubber without the headache and expense.
Hi! I have a question to ask you.
When I mount the Hop-up chamber, I have a loss of tightness.
I go back up and I see that my SBA gasket is cut above the nub window. already two fucking joints in the air knowing that I'm careful.
How to avoid this on a 3rd joint?
Did you try lubricating and slightly rotating during install?
@@Saboteryes I had done everything right and it was useless. Now, I switched to the stalker kraken hopup unit and I have no more problems.
I lost that spring, any idea for replacement?
Try from a pen
What is on your barrel is it a flat bucking ?
Yes. An SBA one
What bucking u use ?
SBA 70 degree
@@Saboter thx
@@Saboter what maxx hop up u take