Just ordered the kraken, interested to see how it compares to the Fast Hop, TNT and maple leaf hop units i have already. Looks very impressive in your videos so really looking forward to testing. :) Can you get 'Kraken' on making some more Morpheus barrels please
Just installed the Kraken into my 22 SRS, CJ barrel, wasp piston and used the S2 arm. AirSeal 100% and shooting very flat past 85ms (range finder used) set 2.5 on the wheel. Will test in a couple of weeks at my next game to check max range vs fast hop w/pdi 6.05 barrel and SB 60 rubber. Very impressed so far though well done to @stalkerairsoft for a great product launch.
How does the kraken compare to the TNT hop? is it a large improvement and would you say putting the money down for a kraken would be worth it if you already got a tnt terminator chamber with 100% airseal?
@@nothinnothin4788 Alignment/Fitment Stalker wins hands down. Airseal achieved straight away but after a couple of hundred shots the nozzle has worn away the lips so may loose that seal over time. The rubber contact patch is good but needs bedding in a lot more then the tnt tr hop rubber needed. I did get some great shots with it and I think consistency will get better but going to order a 70 red stalker hop rubber and see how that does.
Hello, You can install it, please check my other video with rapax hulk test, in that video i explain how u need to cut the bucking to let it work on stock barrel
Hey came across your video here and I have a question about that last o-ring that sits in the outside going into the outer barrel, the oring isn’t big enough I guess and so what I put everything together, the hop up unit doesn’t sit flush and no bb’s don’t feed, is there another solution to this?
Have to say thanks, installed today, so consistent, I was 100% seal with fast hop up, but won 10/15 fps, removed the power ring to be inside limits. Saw the hop up form inside the barrel trough the light and it looks realy straight. 💪💪
So far too say I'm a tad upset.. I bought this the other day arrived yesterday. Went too fit it too my stock barrel. I put it all together shown in the video went checked the hop arm worked lovely... Too then when I put it all together and test the seal.. It leaked so I removed it and taken it apart too find the hop rubber has a slight tear where the hop pushes down. I ordered pack of 3 too replace it and it done the exact same thing... I need help do I need a certain barrel or what!!!
I have got in my SRS-A1 a 520mm PDI barrel, which is a bridged barrel. Will it work with the kraken? I ask this because the barrel window is on these barrels not that big. Which arm do you advise to use if the kraken will work with my PDI barrel, the S1, S2 or S3? When S3 which nub?
Hi Bert, If your window is 5mm or bigger in length it should work! Probably you have to cut the end of the bucking. You can see how i did it in this video: ruclips.net/video/0sjPzptJx3M/видео.html You can use S1 arm for sure and S3 arm with stalker tigra nub. Thanks!
Just ordered the kraken, interested to see how it compares to the Fast Hop, TNT and maple leaf hop units i have already. Looks very impressive in your videos so really looking forward to testing. :) Can you get 'Kraken' on making some more Morpheus barrels please
Just installed the Kraken into my 22 SRS, CJ barrel, wasp piston and used the S2 arm. AirSeal 100% and shooting very flat past 85ms (range finder used) set 2.5 on the wheel. Will test in a couple of weeks at my next game to check max range vs fast hop w/pdi 6.05 barrel and SB 60 rubber. Very impressed so far though well done to @stalkerairsoft for a great product launch.
How does the kraken compare to the TNT hop? is it a large improvement and would you say putting the money down for a kraken would be worth it if you already got a tnt terminator chamber with 100% airseal?
@@nothinnothin4788 Alignment/Fitment Stalker wins hands down. Airseal achieved straight away but after a couple of hundred shots the nozzle has worn away the lips so may loose that seal over time. The rubber contact patch is good but needs bedding in a lot more then the tnt tr hop rubber needed. I did get some great shots with it and I think consistency will get better but going to order a 70 red stalker hop rubber and see how that does.
With the supplied purple rubber,whats the preferred arm to use with a Morpheus ib?
Do you really need to lube the small inner oring? It wont bliw the grease into the inner barrel?
Will this install on the stock SRS or will I need to buy a barrel and add more money?
Hello,
You can install it, please check my other video with rapax hulk test, in that video i explain how u need to cut the bucking to let it work on stock barrel
Hey came across your video here and I have a question about that last o-ring that sits in the outside going into the outer barrel, the oring isn’t big enough I guess and so what I put everything together, the hop up unit doesn’t sit flush and no bb’s don’t feed, is there another solution to this?
Have to say thanks, installed today, so consistent, I was 100% seal with fast hop up, but won 10/15 fps, removed the power ring to be inside limits. Saw the hop up form inside the barrel trough the light and it looks realy straight. 💪💪
Good Vid...but damn $173 CAD for a hop chamber???
Is the same chamber por de left srs version?
i use a crazy jet gbb barrel what hopup arm should i use ?
Does anyone knows where the prowler rubber nub goes?
Great instructional video!
So far too say I'm a tad upset.. I bought this the other day arrived yesterday. Went too fit it too my stock barrel. I put it all together shown in the video went checked the hop arm worked lovely... Too then when I put it all together and test the seal.. It leaked so I removed it and taken it apart too find the hop rubber has a slight tear where the hop pushes down. I ordered pack of 3 too replace it and it done the exact same thing... I need help do I need a certain barrel or what!!!
Did you get it to work?
@@RavenCrypto unfortunately not I resorted too using the silverback fast hop
@@airsoftwookie401 Damn... I'll let you know if I have a better experience. Will start with stock barrel as well
@@RavenCrypto cool...hope u get better experience than I did. But the silverback one works just as good my furthest confirmed hit was 90m using .48g
How does it install with the SRS1 Sport?
I need to know what kinda whaser i need for instaling the kraken hopup into the barrel
I have got in my SRS-A1 a 520mm PDI barrel, which is a bridged barrel. Will it work with the kraken? I ask this because the barrel window is on these barrels not that big. Which arm do you advise to use if the kraken will work with my PDI barrel, the S1, S2 or S3? When S3 which nub?
Hi Bert,
If your window is 5mm or bigger in length it should work! Probably you have to cut the end of the bucking. You can see how i did it in this video:
ruclips.net/video/0sjPzptJx3M/видео.html
You can use S1 arm for sure and S3 arm with stalker tigra nub.
Thanks!