Amazing video. I bought a CH340 Nano board so I had to 1. Download the CH340 .exe drivers, plug in the Nano board, run the CH 340 .exe, click uninstall, click install. 2. Do everything in the video starting from 3:02 but choose "Processor: ATmega328P (Old Bootloader)" for my specific Nano board. 3. Enjoy the functioning Nano board.
mine was also a stk500_recv error - ch340 clone with no underboard crystal next to the ch340-chip-pins7and8, setup as Board:Arduino Nano" Processor:"ATMega328P", changing to the below setting made it work, without doing anything else Tools = Processor: ATMega328P (old bootloader)
A very clear video, but run into the problem that in the new Arduino IDE is not an option for Programmer:"AVRIP mkll. Only burn bootloader. Is that a problem?
I succeeded did the steps. It works, thanks!. But since then everytime I upload a sketch to the Nano, I have to choose "Arduino Uno" instead of "Arduino Nano" (it will be failed to upload if I choose "Arduino Nano").
avrdude: Yikes! Invalid device signature. Double check connections and try again, or use -F to override this check. Failed chip erase: uploading error: exit status 1 I am getting this error, how can I fix it?
Arduino: 1.8.19 (Windows 7), Board: "Arduino Nano, ATmega328P" avrdude: Expected signature for ATmega328P is 1E 95 0F Double check chip, or use -F to override this check. Error while burning bootloader. This report would have more information with "Show verbose output during compilation" option enabled in File -> Preferences sir i am getting this type of error please solve my problem .
avrdude: AVR device initialized and ready to accept instructions Error while burning bootloader. Reading | ################################################## | 100% 0.02s avrdude: Device signature = 0x2fff00 avrdude: Expected signature for ATmega328P is 1E 95 0F Double check chip, or use -F to override this check.
My Arduino nano's show error in uploading sketch....i have right driver also ....than reason of not uploading?........but I see tthat L led(side one to PWR) is blinking very low... seems that get fuse ......can it be reason
Greeting. I have a problem, when I want arduino NANO Burn Loader it shows me an error (avrdude: Expected signature for ATmega328P is 1E 95 0F Double check chip, or use -F to override this check. Failed chip erase: uploading error: exit status 1). What does that mean, what should I do next. HELP. I bought 4 pieces of them through Aliexpress . Greetings from Croatia
i have done all of them and it's done uploading when i try the blink program on the nano. but nothin happens on the led i connected to the nano. why is that?
Am facing some critical issues with nano board. Blink code is properly worked but when upload some other code LCD display or switch opration code these codes is not working how to solve this problem sir?
Thank you this video help me to load programs in my new arduino nano !!, but I need to use other video as well to configure the drivers ruclips.net/video/8cZJ-7KXS34/видео.html this was taken from Elbarto0.0, thank you both !!!
This method does not work if the Nano has a ATmega328PB instead of a 328P: I am still looking for a method for burning a bootloader in a Nano with a ATmega328PB, because most of the chinese clones have a 328PB. Here is the error message with a 328PB: Arduino : 1.8.15 (Windows 10), TD: 1.57, Carte : "Arduino Nano, ATmega328P" C:\Users\Michel\AppData\Local\Arduino15\packages\arduino\tools\avrdude\6.3.0-arduino17/bin/avrdude -CC:\Users\Michel\AppData\Local\Arduino15\packages\arduino\tools\avrdude\6.3.0-arduino17/etc/avrdude.conf -v -patmega328p -cstk500v1 -PCOM9 -b19200 -e -Ulock:w:0x3F:m -Uefuse:w:0xFD:m -Uhfuse:w:0xDA:m -Ulfuse:w:0xFF:m avrdude: Version 6.3-20190619 Copyright (c) 2000-2005 Brian Dean, www.bdmicro.com/ Copyright (c) 2007-2014 Joerg Wunsch System wide configuration file is "C:\Users\Michel\AppData\Local\Arduino15\packages\arduino\tools\avrdude\6.3.0-arduino17/etc/avrdude.conf" avrdude: AVR device initialized and ready to accept instructions Erreur lors de la gravure de la séquence d'initialisation. Reading | ################################################## | 100% 0.02s avrdude: Device signature = 0x1e9516 (probably m328pb) avrdude: Expected signature for ATmega328P is 1E 95 0F Double check chip, or use -F to override this check. avrdude done. Thank you. If you have a solution for the 328PB processor, I am very very interested !
amazing this has just saved one of my arduinos stuck on a serial flood, nice video well explained
I bought 3 nanos and was facing the same problem your video saved my money 🙏🙏🙏🙏🙏
LoL bro! You save my Nano Board and my project and everything. Now i can program my nano in regular bootloader. Thank you very much.
i did it. thank you. mine had two. no comm port, old bootloader. all fixed up. thanks again
It's my pleasure
Amazing video. I bought a CH340 Nano board so I had to
1. Download the CH340 .exe drivers, plug in the Nano board, run the CH 340 .exe, click uninstall, click install.
2. Do everything in the video starting from 3:02 but choose "Processor: ATmega328P (Old Bootloader)" for my specific Nano board.
3. Enjoy the functioning Nano board.
Hi, I did the process. But still not visible my nano in the device manager... :( Please help
Thanks you saved me three arduino that I couldn't use
Great video! no wasting time and clearly explained!
Thanks so much, Other videos didn't work, but this one made it work
Great video clearly explained
Thanks, just recovered my faulty nano clone, excellent and well explained video...5*
Thanks! You helped me fix my code-bricked Nano!
Well explained. It worked like charm with my "bangbad" arduino nano.
Very nice sharing tutorial...
Fantastic! Didn't even know this was a thing you had to do but you explained it perfectly! Amazing video. Thank you so much!
Thank you sir! You saved me a very long journey! Excellent work!
Thanks so much, saved my bricked Nano!
Thank you for Explaining Well🔥🔥♥️ I Saved My Nano🔥😃
Thank you so much, my arduino Micro working again now
thanks bro you help me much
Thank you sir.
My Arduino Nano is working now.
Direct to the point, very useful video. Thanks
Thanks so much
Bro you are the best, you saved the day
Great video... Very comprehensive
Excellent explanation.
More understandable IF you speak more slowly and even write some comments !!
PLEASE
Thanks heaps for this video, very easy to follow and fixed the issue with my new board cheers!
Thank you!
mine was also a stk500_recv error - ch340 clone with no underboard crystal next to the ch340-chip-pins7and8, setup as Board:Arduino Nano" Processor:"ATMega328P", changing to the below setting made it work, without doing anything else
Tools = Processor: ATMega328P (old bootloader)
Please let me add my thanks! You're a genius! How did you know about this?!?
I will try again uplooding my ardino nanu with the new bootludder. Lets hope it works this time. Thanks
thank you, this saved me hours
I will be happy if it works for Arduino Uno to Arduino Uno bootloader burning process.
thank for your very useful tutorial 🌹
Thanks for your comment. Please share your experience.
Very helpful video. Thank you!
Great explanation
Thank you! It works now!
great!! thanks
A very clear video, but run into the problem that in the new Arduino IDE is not an option for Programmer:"AVRIP mkll. Only burn bootloader. Is that a problem?
No
thank you man, God bless you
I succeeded did the steps. It works, thanks!. But since then everytime I upload a sketch to the Nano, I have to choose "Arduino Uno" instead of "Arduino Nano" (it will be failed to upload if I choose "Arduino Nano").
For that you should choose the correct board during bootloader
Nice video, keep it up, thank you for sharing it :)
I am also getting same problem so I will try it should I connect Vin to Vin pin or can I connect +5 v to Vcc pin of nano
nice🥰🥰🥰🥰
السلام عليكم
بس اخي التوصيلات بين الاردوينو الأول والثاني إذا ممكن توضح أكثر
avrdude: Yikes! Invalid device signature.
Double check connections and try again, or use -F to override
this check.
Failed chip erase: uploading error: exit status 1
I am getting this error, how can I fix it?
Error while burning bootloader
This msz comes when upload the bootloader program.
Arduino: 1.8.19 (Windows 7), Board: "Arduino Nano, ATmega328P"
avrdude: Expected signature for ATmega328P is 1E 95 0F
Double check chip, or use -F to override this check.
Error while burning bootloader.
This report would have more information with
"Show verbose output during compilation"
option enabled in File -> Preferences
sir i am getting this type of error please solve my problem .
avrdude: AVR device initialized and ready to accept instructions
Error while burning bootloader.
Reading | ################################################## | 100% 0.02s
avrdude: Device signature = 0x2fff00
avrdude: Expected signature for ATmega328P is 1E 95 0F
Double check chip, or use -F to override this check.
You save me ! Thx a lot !
Thanks for your feedback
Thank you vai
There is a mistake in your schematic,
You showed Vin to Vin...
which will be Nano Vin to Uno 5v
When we are powering the Module using usb then it will be ok. No problem.
me salvaste, tuma tu like y mi suscripcion es tuya jeje nice
My Arduino nano's show error in uploading sketch....i have right driver also ....than reason of not uploading?........but I see tthat L led(side one to PWR) is blinking very low... seems that get fuse ......can it be reason
You must need to burn the bootloader. Follow this video.
arduino nano to arduino uno ko led blinking program karen with smartphone
Greeting. I have a problem, when I want arduino NANO Burn Loader it shows me an error (avrdude: Expected signature for ATmega328P is 1E 95 0F
Double check chip, or use -F to override this check.
Failed chip erase: uploading error: exit status 1). What does that mean, what should I do next. HELP. I bought 4 pieces of them through Aliexpress . Greetings from Croatia
Yeah me too.
Which board are you using for bootloader?
@@NTTronix I'm using Arduino Uno as programmer, Arduino Pro Micro as the target.
i have done all of them and it's done uploading when i try the blink program on the nano. but nothin happens on the led i connected to the nano. why is that?
Please show me the connection diagaram
ok i have 1x arduino uno, and 3x arduino nano typ-c and not soldered how can i do withouth pins O_O
Am facing some critical issues with nano board.
Blink code is properly worked but when upload some other code LCD display or switch opration code these codes is not working how to solve this problem sir?
I think there have any mistake on your program
@@NTTronix but sir UNO board properly worked with same code.
@@0124akash Then burn the bootloader first
@@NTTronix problem solved. Actual problem is supply voltage. Nano board supply range 6-12V and am applying 4.8V through mobile charger.
I am getting the same ardude error while uploading the sketch in Arduino Uno also. what shall I do now?
Burn the bootloader
i got this "error while burning bootloader" how to fix this error please
Check all the connection. It happens mainly for poor quality wire.
dont work!!!! "Failed chip erase: uploading error: exit status 1" use working arduino mega 2560
Only green light is blinking...at power point
Thank you this video help me to load programs in my new arduino nano !!, but I need to use other video as well to configure the drivers ruclips.net/video/8cZJ-7KXS34/видео.html this was taken from
Elbarto0.0, thank you both !!!
I am getting invalid device signature
try to disable device driver signature. search on google about this or use Windows 10
I'm still facing issue while uploading
I think you didn't burn the bootloader perfectly
This method does not work if the Nano has a ATmega328PB instead of a 328P: I am still looking for a method for burning a bootloader in a Nano with a ATmega328PB, because most of the chinese clones have a 328PB.
Here is the error message with a 328PB:
Arduino : 1.8.15 (Windows 10), TD: 1.57, Carte : "Arduino Nano, ATmega328P"
C:\Users\Michel\AppData\Local\Arduino15\packages\arduino\tools\avrdude\6.3.0-arduino17/bin/avrdude -CC:\Users\Michel\AppData\Local\Arduino15\packages\arduino\tools\avrdude\6.3.0-arduino17/etc/avrdude.conf -v -patmega328p -cstk500v1 -PCOM9 -b19200 -e -Ulock:w:0x3F:m -Uefuse:w:0xFD:m -Uhfuse:w:0xDA:m -Ulfuse:w:0xFF:m
avrdude: Version 6.3-20190619
Copyright (c) 2000-2005 Brian Dean, www.bdmicro.com/
Copyright (c) 2007-2014 Joerg Wunsch
System wide configuration file is "C:\Users\Michel\AppData\Local\Arduino15\packages\arduino\tools\avrdude\6.3.0-arduino17/etc/avrdude.conf"
avrdude: AVR device initialized and ready to accept instructions
Erreur lors de la gravure de la séquence d'initialisation.
Reading | ################################################## | 100% 0.02s
avrdude: Device signature = 0x1e9516 (probably m328pb)
avrdude: Expected signature for ATmega328P is 1E 95 0F
Double check chip, or use -F to override this check.
avrdude done. Thank you.
If you have a solution for the 328PB processor, I am very very interested !