I installed drivers, checked for port set port as shown in device manager, set Arduino as ISP but it showing error while uploading, i changed nano bit also it's showing same error
@@mission_critical it was showing that unable to upload code to board, after doing every steps provided by u still it's showing same error, then i randomly chaned one option showing atmega 328bootloader to atmega 328(old bootloader) then again i upload the code now this time the successfully uploaded 😊😊😊 tyso mch🤗🤗.request u to add this common problem also😉
@@mission_critical I am having the same problem as above, but the boot loader will not burn to the nano. No combination of settings helps. the nano I have already has the blink program running from when I got it. how do I get it to burn the boot loader???
Thank you so much! I ordered a few of these nanos and none of them worked. I was pulling my hair out. Following you excellent guide I installed the correct driver and burning the boot loader and they are working great! Thank you again!
That must have been a pain in the ass. How far into assembly were you, and were you still prototyping when you found the bug? Anyways, I hope you didn't have to use the solder sucker too much!
i have a nano clone. I installed ch34x drivers but the computer still cant detect the board. it doest show anything under the ports tab in device maager
Hi I tried uploading the bootloader. I am using the latest IDE 2.1.1. And I am getting the error avrdude: Expected signature for ATmega328P is 1E 95 0F Double check chip, or use -F to override this check. Failed chip erase: uploading error: exit status 1 What should be done?
I have installed CH340 driver, set everything on IDE, but my computer still can't detect a new port for my Nano, other than the existing ports. And no port connected to CH340 in device manager. The Nano power LED lights up, the 'L' LED blinks... and nothing else. I can't load any sketch to my Nano since my computer can't detect the port. Help..!!
I have solderder the one side of ale pin to pcb and not souldered it on arduino side is this the reason My arduino nano board is unable to get power supply from battry
my arduino board is unable to get power supply through pcb battery and working properly whily connected directly throuch laptop..........what can be the reason behind ......is it because i have not souldered header pins on nano board but only on one side i.e.pcb
@@mission_critical Done by still not working When I put power supply from the outside using the power pins or the power jack the yellow led is blinking and then it remains dim Once I have used 12v supply and led it to remain for 3 days and since then it is not working . I think that it was over loaded . CAN YOU HELP ME TO FIX IT ? ? ? ONE MORE THING THAT MY ONE IS ARDUINO UNO
when I clicked burn bootloader this is what it is showing avrdude: Expected signature for ATmega328P is 1E 95 0F Double check chip, or use -F to override this check. Failed chip erase: uploading error: exit status 1
Hola ..can you help me here...i am not getting any movements from my mitor wheels...i am using freenove fnk0041 car kit , what could i be doing wrong.....any help would be appreciated.
my arduino nano board's power led is on but (L) led is not blinking when i plug board. but i show that the board is connected to the arduino software. but the programme is not being upload. please give me a solution how i repair my board?
Hi bro I am using AVR mega 2560 its uart communication was mismatched so I was replaced my crystal oscillator ... And now tx rx communication not working and not showing arduino mega in system driver .... How should I solve this problem ? Ple help me....
I followed all the steps, but when "Burl bootloader" says "Invalid device signature." Device signature = 0x000000. Keepek the connection, I uploaded the blink test, both the UNO and NANO blinked. But the NANO alone is not recognized by windows, no changed in Device Manager. Once it worked, than started to say "Error installing device" and now nothing happens. Is the NANO damaged?
Yes, if you see " invalid device signature" I think your nano is static damaged! , But still try installing drivers in accordance to your USB communication ic! Thanks a lot for Subscribing! Appreciate your interaction
At first I had no big hopes that this video will help me, because I already watched lots of other Videos with problems about the Arduino nano. But when I tested to burn the Bootloader using my working Arduino Uno, it worked. Thank you!!!
Hi I have an Arduino Nano clone and I can't get the serial port recognized although I downloaded the driver. But I can load the Bootloader via an Arduino Uno. So my question is: Can I load sketches to the Nano via the Uno. That would save me .... Many thanks ahead.
If you can't upload the bootloader, it's not the problem of communication with the IC, it's the problem with IC, so i dont think you would be able to upload anything with that arduino, since chip is damaged, i would highly suggest you to first check the USB wire, and remove any circuit that arduino would be connected to and simply upload the code on bare arduino
Hi, after run through problem #4, it says - after i've uploaded both the UNO and the NANo the ArduinoISP - that everything is okay. However after that, when i try to upload the 'blink' program to the nano, it says it uploaded it, but it did not work. I tried other programs, or changing the blink to output the led to pin 9, but its just won't work. The output is this: Reading | ################################################## | 100% 0.31s avrdude: verifying ... avrdude: 2146 bytes of flash verified avrdude done. Thank you. What can be the problem?
Hi @Mission Critical Im Struggling Here I Have The Same Board But I Get This Error avrdude: ser_open(): can't open device "\\.\COM13": Access is denied. I Have Tried All Apart From Bootloader As I Do Not Have A UNO Board Any Help Will Be Much Appreciated Thanks
avrdude: Yikes! Invalid device signature. Double check connections and try again, or use -F to override this check. Error while burning bootloader. Help. I keep getting this error every time i attempt to burn the nano's bootloader
No, luckily Arduino Uno is safe and prone to take those kind of mistakes, just don't over power it, ( don't supply 15 v or so on 5 V pins ) other than that, if you make mistake while bootloading, simply go again and follow the steps again
My arduino nanos led is blinking but it is not working means when I connect it to pc and try to install drivers it shows me 'driver pre install failure' pls help
I think your computer already has this drivers installed, try to unistall that drivers and reinstall the package as I mentioned in the video and led is blinking means it's power status led, that means your board must be fine, not sure about atmega chip, try to reinstall the drivers and let me know what output you get
Hi, I do have an arduino programmed with an hex file who sends characters to a lcd screen, I want to copy the file but when using AVRDUDESS I can't detect the nano clone, any idea how to copy hex file to clon? thanks
I have arduino nano clone version with atmega 328p. And I use arduinodroid for the program. And whenever I try to upload my sketch it shows "programmer not responding" and there is nothing connected to tx1 and rx1 pins. What's the issue here and how can I solve it sir? And also when i choose the board type as "nano w atmega328p (old bootloader)" it shows check board type.
I just changed to Big Sur OS...now the Arduino IDE will not open. Sp I use PlatformIO. I have an esp32 dev mod and a Heltec esp32 wifi kit. Platform I will not uplad due to error either timed out waiting for header or wrong com port. The only com prt I can find in PIO is bluetooth incoming port.
I ordered an Arduino uno(no small or smd version) supposed to be genuine. I need to use A4 input to read voltage or use Ina219 to read current sense. Regardless I do, I have no answer if I use a4 input. If I measure with a voltmeter A4 and Gnd I'll read 5volts. I am able to upload code. Is this a bad board? A4 shouldn't be present 5 volts I think.
Mine won't work, step 6 I'll get this error, Can you tell me what to do? avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x15 avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0x14 avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0x01 avrdude: stk500_initialize(): (a) protocol error, expect=0x14, resp=0x10 avrdude: initialization failed, rc=-1 Double check connections and try again, or use -F to override this check. avrdude: stk500_disable(): unknown response=0x12 Fout bij het branden van de bootloader.
I haven't uploaded any program but still the led keeps on blinking and if I try to upload is shows problem uploading to board please help I tried all your suggestions
i think your atmega 328 chip is damaged, else the USB interface ic is not working, if the led is automatically blinking and tx,rx pin doesn't flicker during your uploads, i think you need to get a new arduino board
Hey I tried your burn bootloader method and it displayed a successful bootload but after disconnecting it and uploading code again it is showing the same issue ( avrdude: ser_open(): can't set com-state for "\\.\COM3" Failed uploading: uploading error: exit status 1). Can you guide me through this process again or suggest me some other solution to this.
sir ,it dump the program is done.blinking program is good to run. but i connect ir sensor and relay but doesn't work properly its work always run or not improper
when i insert GND on Uno , UNO goes off and Nano also goes off , they are not even detected, when i remove GND pin on UNO everything is up , but in the end bootloader fails, pls suggest
I have connected a TSOP 1838 to an arduino nano uploading the code its totally OK but displaying the code on the serial monitor is the big issue please help me with that
@@mission_critical It was a pain trying to figure out what I received for operating a stepper motor for tracking celestial objects. With what seems countless possibilities of which device it was getting to be a pain for checking what's loaded and what separate electronics and their wiring it had.
Your videos are good but there is a huge disparity in the audio levels between your voice recording and the music... With the sound level set so I can hear your voice, when the music comes on, my neighbors get an ear full 2 blocks away. :)
hahahaha, first of all thank you so much for supporting me inspite of shortcomings in my videos, but i will really consider this point while editing my future videos, thank you koshus for bringing this glitch into notice.
Hi, nice and clear video, I have MACBook Ail and I bought Arduino nano clone and I cannot find the serial port options (grey button) even I had download the the CH340 divers, but the USB serial port still remain disabled, how I can solve this matter? thanks in advance Roberto
Can you help me with my problem? "PWR" led on my nano board is red, "L" led is blinking red. When i connect board to the shield then I have only red "PWR" led and following errors: WARNING: Category '' in library UIPEthernet is not valid. Setting to 'Uncategorized' Sketch uses 21256 bytes (69%) of program storage space. Maximum is 30720 bytes. Global variables use 1625 bytes (79%) of dynamic memory, leaving 423 bytes for local variables. Maximum is 2048 bytes. Low memory available, stability problems may occur. An error occurred while uploading the sketch Invalid version '1.04' for library in: D:\Documents\Arduino\libraries\arduino_uip-master Invalid version '1.04' for library in: D:\Documents\Arduino\libraries\arduino_uip-master avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x9f avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x9f avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x9f avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x9f avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x9f avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x9f avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x9f avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x9f avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x9f avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x9f Problem uploading to board. See www.arduino.cc/en/Guide/Troubleshooting#upload for suggestions. Invalid version '1.04' for library in: D:\Documents\Arduino\libraries\arduino_uip-master Invalid version '1.04' for library in: D:\Documents\Arduino\libraries\arduino_uip-master
First remove your arduino from the module and program it, ( sometimes modules use TX and RX pins of arduino which prevent arduino to code when connected) If it doesn't works for you, simply try to bootload your Arduino! Thank you for subscribing to Mission Critical!
I try to operate different sketches for lighting to ON a number of LEDs, but this board of nano can only handle 4 LEDs per sketch and no more. Is there a solution? Thank you.
hi, I am using arduino nano and could not get rid of the problem . Here is Problem below. Sketch uses 930 bytes (3%) of program storage space. Maximum is 30720 bytes. Global variables use 9 bytes (0%) of dynamic memory, leaving 2039 bytes for local variables. Maximum is 2048 bytes. avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x28 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x28 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x28 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x28 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x28 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x28 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x28 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x28 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x28 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x28 Problem uploading to board. See www.arduino.cc/en/Guide/Troubleshooting#upload for suggestions. Invalid library found in C:\Users\Habib Daood Rathore\Documents\Arduino\libraries\sketch_dec11a: no headers files (.h) found in C:\Users\Habib Daood Rathore\Documents\Arduino\libraries\sketch_dec11a Invalid library found in C:\Users\Habib Daood Rathore\Documents\Arduino\libraries\sketch_dec11a: no headers files (.h) found in C:\Users\Habib Daood Rathore\Documents\Arduino\libraries\sketch_dec11a
Hi there I don't have a UNO, so I couldn't do the bootloader step. My Win 11 shows my Nano clone on COM 3, CH341 is installed, baud-rate: 9600 I've tried to make the Nano blink using the example in Arduino IDE 2.1.0 (also 1.8.19). Board: Arduino Nano Port: COM3 Processor: ATmega328P (ATmega328P old) What I see is: Using Port : COM3 Using Programmer : arduino Overriding Baud Rate : 115200 avrdude: ser_open(): can't set com-state for "\\.\COM3" avrdude done. Thank you. Fehlgeschlagenes Hochladen: Hochladefehler: exit status 1 I've used four cables. Any advice? Thanks in advance
i faced a problems on the pins of A6 and A7 on arduino nano once i program using those pins especially on simple blinking and keypad interfacing using those pins but doesnt give an output but once i use other pins they work perfectly, how to solve it?
Bro! On my nano as i pug in usb all led lights (rx,tx,and power)starts to glow except (L) labeled led .my pc and mobile shows no arduino board found ...please help me out..nano was working recently...please help
I think you burnt your Arduino officially, did you short circuited or may be applied over voltage or something to the board, if yes, it might be damaged else it might be a defective board, Thank you for subscribing to Mission Critical
Hi bro I have an Arduino Uno clone. I had the 2nd problem. But I solved it. Now I am facing the 3rd problem. Arduino Uno board is not displaying in my boards list. How can I fix it...?
i purchased arduino uno clone ,i installed ch340 driver but when i connect the board nothing happens in my laptop ,even no connection notification no popup no port in device manager and no port in IDE but all 4 leds are glowing what should i do plzz help!!
i got 20 of the nano's and i get this on almost all, almost the same error, can you give me some advice? Arduino: 1.8.13 (Windows 10), Board: "Arduino Nano, ATmega328P (Old Bootloader)" Sketch uses 1692 bytes (5%) of program storage space. Maximum is 30720 bytes. Global variables use 204 bytes (9%) of dynamic memory, leaving 1844 bytes for local variables. Maximum is 2048 bytes. avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0xfc avrdude: stk500_initialize(): (b) protocol error, expect=0x10, resp=0xfc avrdude: initialization failed, rc=-1 Double check connections and try again, or use -F to override this check. the selected serial port does not exist or your board is not connected
Hi bro help me :( my arduino uno don't upload: An error occurred while uploading the sketch avrdude: stk500_paged_load(): (a) protocol error, expect=0x10, resp=0x00 avrdude: stk500_cmd(): programmer is out of sync avr_read(): error reading address 0x0000 read operation not supported for memory "flash" avrdude: failed to read all of flash memory, rc=-2 avrdude: stk500_disable(): protocol error, expect=0x14, resp=0x00
Hi in my clone one problem is happened like when ever I connect to the power or laptop its light blinkes and off and it happens again and again...Please help with a solution.
Hi, I am having problems with new nanos. I need the old loader versions, which work perfectly for me. Is there a way to know when purchasing them, or can I use this method in the video, to upload the old boot loader onto a new boot loader?
I just select arduino NANO as board and click the respected COM and uploaded a simple sketch BUT the compiling REAAAALLLLY takes forever to upload and after 3mins or so the arduino IDE is displaying error about that simple sketch and i dont know what to do cause i need that board for my next proj
Try to disconnect everything on the board, just connect Arduino board, without any connections and try again, if it still doesn't work, try to change baud rate to 9600
What this error is about? i can''t upload my code into Ardunino nano Arduino: 1.8.10 (Windows 10), Board: "Arduino Nano, ATmega328P" Sketch uses 892 bytes (2%) of program storage space. Maximum is 30720 bytes. Global variables use 9 bytes (0%) of dynamic memory, leaving 2039 bytes for local variables. Maximum is 2048 bytes. Error downloading downloads.arduino.cc/packages/package_index.json An error occurred while uploading the sketch avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x72 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x72 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x72 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x72 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x72 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x72 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x72 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x72 avrdude: ser_recv(): read error: Access is denied. avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x72 avrdude: ser_send(): write error: sorry no info avail avrdude: ser_recv(): read error: Access is denied. avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x72 avrdude: ser_drain(): read error: Access is denied. This report would have more information with "Show verbose output during compilation" option enabled in File -> Preferences.
I followed the instructions, and everything was going fine up till the point where I attempted to burn bootloader to the nanoboard. I'm having an error that just says this:
keep getting this error avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x1c have checked board is conected in device manager and is on comport 3. but still struggling
It's really weird, i have 2 Arduino Nano clones, and i have really weird values on analog pins (even the pot read example throws weird values when moving the Arduino/wires around). I didn't flash anything/installed the CH340C drivers cause they got recognized as soon as i plugged them in my computer. Also i'm sure my pots are okay i tested with a multimeter, maybe bad AliExpress wires or just the board itself having problems
Hello to Mission Critical. I really appreciate your video on how to fix nano issues. My nano gets heated (chip) once I connect the usb to the pc with no load, and it does not upload the sketch. Can adivise with that ?
Hey, i found one solution for this problem, can you first try to upload the code and then connect the circuit. / Device, please let me know if it works for you
I think there must be some problem with your hard disk on computer, definately not Arduino problem, this is simply not possible for Arduino to crash your pc, definitely get your pc checked
My ardiuno nano board is working already but now not working . boot loader not working proper. power led is working . uploading is working very slowly. uploading files is not working
I think you officially burnt your Arduino board, this happened to me too! I accidentally shorted the Arduino 5 v with 12v supply, and then ic completely stopped working! Still just to make sure,why don't you try changing the usb wire, it solved 90% of the peoples problems for this issue ! Thank you for subscribing to Mission Critical
I am trying to upload code but I get this:avrdude: jtagmkII_getsync(): timeout/error communicating with programmer (status -1) then executing command oh and also I have a lafvin nano
I'm having the same problem with nano clone, COM4, Programmer: ArduinoISP avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x28 avrdude: stk500_recv(): programmer is not responding When I select ATmega328P Old bootloader, it gets uploaded (blink) but delay(1000) = 1 second is more like 4 seconds. Any idea what might be the reason for that? Thanks.
avrdude: Yikes! Invalid device signature. Double check connections and try again, or use -F to override this check. Failed chip erase: uploading error: exit status 1 I got these error wfen i click burnbootloader
Went through each step and still cant get my nanos to upload the ide consistantly. I usually see this error: avrdude: ser_open(): can't open device "\\.\COM3": Access is denied. Problem uploading to board. See www.arduino.cc/en/Guide/Troubleshooting#upload for suggestions. I've gotten the nanos to work a couple times, but they will usually show that error message. After installing the drivers and burning the bootlader with my uno, even the uno will show this error message at times. Any thoughts?
Thank you very much! I had to do the bootloader burn on my 3 that I got 2 weeks ago. I couldn't upload anything, and got frustrated, and now they're working like a charm 😋 thank you!
Please refer to my LCD tutorial, and first clear the basics there before proceeding to this project, and please feel free to comment and share for any confusion further
Nice video I want to connect arduino nano(with circuits) to multiwii drone pc app for project So plz suggest me Should i buy Ch340 nano arduino or else which? And how to know that it is not a clone
Um, first factor is cost, look on Arduino website, and the cost of Arduino Nano that you purchased, second thing original Arduino never has ch340/ch341, because it uses FTDI, and I didn't understand your first question, what do you want to do with multiwii drone pc app?
No, clone is exactly similar, if you are careful enough, you would easily use this clone for years, and yes I saw the multiwii flight controller, you can use Arduino Nano and Nano clone for that as well✌️
Getting error No sound when we plug in Arduino nano to computer no device found under device manager only one port is visible in Arduino all settings (ie. seleting arduino namo, selecting atmega32 etc.) are perfect still getting error -------------------------------------------------------------------------------------------------------------- Global variables use 331 bytes (16%) of dynamic memory, leaving 1717 bytes for local variables. Maximum is 2048 bytes. avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x30 avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x20 avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x30 avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x20 avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x30 avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x20 avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x30 avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x20 avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x30 avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x20 An error occurred while uploading the sketch any solution??
Hello there, can you please Message on Instagram, I am not sure how well could I help you in comments section, you can find link to my social media in video description
I installed drivers, checked for port set port as shown in device manager, set Arduino as ISP but it showing error while uploading, i changed nano bit also it's showing same error
What error?
@@mission_critical it was showing that unable to upload code to board, after doing every steps provided by u still it's showing same error, then i randomly chaned one option showing atmega 328bootloader to atmega 328(old bootloader) then again i upload the code now this time the successfully uploaded 😊😊😊 tyso mch🤗🤗.request u to add this common problem also😉
Yes sure, I will pin your comment and make sure everyone gets to see it! Thanks for the update
@@anzilasheikh3622 tysm it helped...
@@mission_critical I am having the same problem as above, but the boot loader will not burn to the nano. No combination of settings helps. the nano I have already has the blink program running from when I got it. how do I get it to burn the boot loader???
Thank you so much! I ordered a few of these nanos and none of them worked. I was pulling my hair out. Following you excellent guide I installed the correct driver and burning the boot loader and they are working great! Thank you again!
You are most welcome, glad to know my video was helpful 😍😉
My Arduino nano clone upload sketches normally some some work properly and some stops randomly even though I have tested them on original Arduino uno
It's probably because of bad USB serial communication chip try bootloading else get a new clone
That must have been a pain in the ass. How far into assembly were you, and were you still prototyping when you found the bug? Anyways, I hope you didn't have to use the solder sucker too much!
i have a nano clone. I installed ch34x drivers but the computer still cant detect the board. it doest show anything under the ports tab in device maager
Will post a solution soon, be subscribed
Hi I tried uploading the bootloader. I am using the latest IDE 2.1.1. And I am getting the error
avrdude: Expected signature for ATmega328P is 1E 95 0F
Double check chip, or use -F to override this check.
Failed chip erase: uploading error: exit status 1
What should be done?
I have the same problem....could not find a solution
+1
I have installed CH340 driver, set everything on IDE, but my computer still can't detect a new port for my Nano, other than the existing ports. And no port connected to CH340 in device manager. The Nano power LED lights up, the 'L' LED blinks... and nothing else. I can't load any sketch to my Nano since my computer can't detect the port. Help..!!
I have solderder the one side of ale pin to pcb and not souldered it on arduino side is this the reason My arduino nano board is unable to get power supply from battry
i am not sure if i totally understood your problem, can you clarify?
my arduino board is unable to get power supply through pcb battery and working properly whily connected directly throuch laptop..........what can be the reason behind ......is it because i have not souldered header pins on nano board but only on one side i.e.pcb
my arduino UNO board is not uploading any sketches since 3 weeks
the yellow LED is glowing but it is dim
what to do please help
please please please
Try discontinuing your circuit, changing your USB wire
@@mission_critical Done by still not working
When I put power supply from the outside using the power pins or the power jack the yellow led is blinking and then it remains dim
Once I have used 12v supply and led it to remain for 3 days and since then it is not working . I think that it was over loaded .
CAN YOU HELP ME TO FIX IT ? ? ?
ONE MORE THING THAT MY ONE IS ARDUINO UNO
Tx and RX pin not working is there any other pin as tx RX please make an video on it
In arduino uno
Sure, we will look at onto it, thank you for subscribing to Mission Critical
when I clicked burn bootloader this is what it is showing
avrdude: Expected signature for ATmega328P is 1E 95 0F
Double check chip, or use -F to override this check.
Failed chip erase: uploading error: exit status 1
I guess there is mismatch between the chip you have on your board and the one available on ide
@@mission_critical how to identify ??🥲
Hola ..can you help me here...i am not getting any movements from my mitor wheels...i am using freenove fnk0041 car kit , what could i be doing wrong.....any help would be appreciated.
my arduino nano board's power led is on but (L) led is not blinking when i plug board.
but i show that the board is connected to the arduino software.
but the programme is not being upload.
please give me a solution how i repair my board?
updated video coming soon, be subscribed !
Hi bro I am using AVR mega 2560 its uart communication was mismatched so I was replaced my crystal oscillator ... And now tx rx communication not working and not showing arduino mega in system driver .... How should I solve this problem ? Ple help me....
I think you need to tune usb interface chip
How can tune this u have any idea about this?
an update video coming soon, please be subscribed.
I followed all the steps, but when "Burl bootloader" says "Invalid device signature." Device signature = 0x000000. Keepek the connection, I uploaded the blink test, both the UNO and NANO blinked.
But the NANO alone is not recognized by windows, no changed in Device Manager. Once it worked, than started to say "Error installing device" and now nothing happens. Is the NANO damaged?
Yes, if you see " invalid device signature" I think your nano is static damaged! , But still try installing drivers in accordance to your USB communication ic!
Thanks a lot for Subscribing! Appreciate your interaction
@@mission_critical Thank you for the fast reply. Have a nice day.
Sure! You too have a great day and hopefully you learnt a thing or two on this channel!
~ Team Mission Critical
At first I had no big hopes that this video will help me, because I already watched lots of other Videos with problems about the Arduino nano. But when I tested to burn the Bootloader using my working Arduino Uno, it worked. Thank you!!!
Thank you so much for supporting my work, this kind of support make my day 🥂 thank you so much 😁
You helped me, so I also can help you 👍😉
Hi I have an Arduino Nano clone and I can't get the serial port recognized although I downloaded the driver. But I can load the Bootloader via an Arduino Uno. So my question is: Can I load sketches to the Nano via the Uno. That would save me .... Many thanks ahead.
If you can't upload the bootloader, it's not the problem of communication with the IC, it's the problem with IC, so i dont think you would be able to upload anything with that arduino, since chip is damaged, i would highly suggest you to first check the USB wire, and remove any circuit that arduino would be connected to and simply upload the code on bare arduino
@@mission_critical
@@mission_critical
updated video coming soon, be subscribed
Hi, after run through problem #4, it says - after i've uploaded both the UNO and the NANo the ArduinoISP - that everything is okay.
However after that, when i try to upload the 'blink' program to the nano, it says it uploaded it, but it did not work. I tried other programs, or changing the blink to output the led to pin 9, but its just won't work.
The output is this:
Reading | ################################################## | 100% 0.31s
avrdude: verifying ...
avrdude: 2146 bytes of flash verified
avrdude done. Thank you.
What can be the problem?
Hi @Mission Critical Im Struggling Here I Have The Same Board But I Get This Error
avrdude: ser_open(): can't open device "\\.\COM13": Access is denied.
I Have Tried All Apart From Bootloader As I Do Not Have A UNO Board
Any Help Will Be Much Appreciated Thanks
I guess you need to close " serial port " and disconnect any circuit connected,
Thank you for subscribing to Mission Critical
avrdude: Yikes! Invalid device signature.
Double check connections and try again, or use -F to override
this check.
Error while burning bootloader.
Help. I keep getting this error every time i attempt to burn the nano's bootloader
hi i have a nano with tx and power lights on the board will not reset and i cannot upload sketch to it it seems to have died overnight
If anything goes wrong while burning bootloader into NaNo, will it damage my working UNO?
No, luckily Arduino Uno is safe and prone to take those kind of mistakes, just don't over power it, ( don't supply 15 v or so on 5 V pins ) other than that, if you make mistake while bootloading, simply go again and follow the steps again
My arduino nanos led is blinking but it is not working means when I connect it to pc and try to install drivers it shows me 'driver pre install failure' pls help
I think your computer already has this drivers installed, try to unistall that drivers and reinstall the package as I mentioned in the video and led is blinking means it's power status led, that means your board must be fine, not sure about atmega chip, try to reinstall the drivers and let me know what output you get
I don't have computer i tried on two or more than two computers and also tried uploading with android but it is not getting detected pls help
Should I try burning bootloader...
I think it's missing drivers, try ch340 drivers instead of ch341, not sure about Android but for PC this should detect , else the wire would be faulty
Android directly has options of ch340 but still when I connect it to pc it is not getting detected but I will still try returning it
Hi, I do have an arduino programmed with an hex file who sends characters to a lcd screen, I want to copy the file but when using AVRDUDESS I can't detect the nano clone, any idea how to copy hex file to clon? thanks
I have arduino nano clone version with atmega 328p. And I use arduinodroid for the program. And whenever I try to upload my sketch it shows "programmer not responding" and there is nothing connected to tx1 and rx1 pins. What's the issue here and how can I solve it sir? And also when i choose the board type as "nano w atmega328p (old bootloader)" it shows check board type.
I just changed to Big Sur OS...now the Arduino IDE will not open. Sp I use PlatformIO. I have an esp32 dev mod and a Heltec esp32 wifi kit. Platform I will not uplad due to error either timed out waiting for header or wrong com port. The only com prt I can find in PIO is bluetooth incoming port.
I ordered an Arduino uno(no small or smd version) supposed to be genuine.
I need to use A4 input to read voltage or use Ina219 to read current sense.
Regardless I do, I have no answer if I use a4 input. If I measure with a voltmeter A4 and Gnd I'll read 5volts.
I am able to upload code.
Is this a bad board? A4 shouldn't be present 5 volts I think.
I bought an Arduino nano but when I connected it to my pc It only blinks and it's not seen in the device manager, any advice?
Try checking the USB wire, else it would be bootloader problem
@@mission_critical I have done the bootloader and was able to have the led blink , i will buy a different cable and try it .
Thanks for the reply
Glad I could help!
thank you for subscribing to Mission Critical
Mine won't work, step 6 I'll get this error, Can you tell me what to do?
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x15
avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0x14
avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0x01
avrdude: stk500_initialize(): (a) protocol error, expect=0x14, resp=0x10
avrdude: initialization failed, rc=-1
Double check connections and try again, or use -F to override
this check.
avrdude: stk500_disable(): unknown response=0x12
Fout bij het branden van de bootloader.
Update Video coming soon, be subscribed
As I connect my cable with nano it dont blink what can I do now
Will post a solution soon!
I'm unable to upload code from my phone to nano clone. It keeps showing problem uploading to the board. How can I fix it??😞
I haven't uploaded any program but still the led keeps on blinking and if I try to upload is shows problem uploading to board please help I tried all your suggestions
i think your atmega 328 chip is damaged, else the USB interface ic is not working, if the led is automatically blinking and tx,rx pin doesn't flicker during your uploads, i think you need to get a new arduino board
@@mission_critical i just changed the processor to old boostloader and the uploading was done thank you your video was very helpful
Glad that it worked, because this was a terminal problem! I will make a update video soon! Thank you for bringing this to my notice!
Hey I tried your burn bootloader method and it displayed a successful bootload but after disconnecting it and uploading code again it is showing the same issue ( avrdude: ser_open(): can't set com-state for "\\.\COM3"
Failed uploading: uploading error: exit status 1). Can you guide me through this process again or suggest me some other solution to this.
sir ,it dump the program is done.blinking program is good to run. but i connect ir sensor and relay but doesn't work properly its work always run or not improper
Which programer should I use for Arduino nano
Use the same programmer, since Arduino Nano, uno, or mega it won't make difference, as the communication protocol is same always 😁
Can I use arduino as ISP
Yes ofcourse buddy, let me know if you need more help! Tech Team is dedicated to solving your Problems !
~ Akshay Momaya
From Mission Critical
as you said i installed ch340.. and it showed the port too... the code is not uploading
Try changing your USB cable, many of my subscribers succeeded in this step by changing their usb wire
when i insert GND on Uno , UNO goes off and Nano also goes off , they are not even detected, when i remove GND pin on UNO everything is up , but in the end bootloader fails, pls suggest
I have connected a TSOP 1838 to an arduino nano uploading the code its totally OK but displaying the code on the serial monitor is the big issue please help me with that
Would be nice if there would be an Arduino board identification that worked with all boards. Unknown 1A86 is what I receive.
yes, seems intresting, let's see if something like this comes up
@@mission_critical It was a pain trying to figure out what I received for operating a stepper motor for tracking celestial objects. With what seems countless possibilities of which device it was getting to be a pain for checking what's loaded and what separate electronics and their wiring it had.
@@nightwaves3203 there is a code called as I2C scanner, use that and comment every device or may be define them as variables
Your videos are good but there is a huge disparity in the audio levels between your voice recording and the music... With the sound level set so I can hear your voice, when the music comes on, my neighbors get an ear full 2 blocks away. :)
hahahaha, first of all thank you so much for supporting me inspite of shortcomings in my videos, but i will really consider this point while editing my future videos, thank you koshus for bringing this glitch into notice.
Hi, nice and clear video, I have MACBook Ail and I bought Arduino nano clone and I cannot find the serial port options (grey button) even I had download the the CH340 divers, but the USB serial port still remain disabled, how I can solve this matter? thanks in advance Roberto
Can you help me with my problem?
"PWR" led on my nano board is red, "L" led is blinking red.
When i connect board to the shield then I have only red "PWR" led and following errors:
WARNING: Category '' in library UIPEthernet is not valid. Setting to 'Uncategorized'
Sketch uses 21256 bytes (69%) of program storage space. Maximum is 30720 bytes.
Global variables use 1625 bytes (79%) of dynamic memory, leaving 423 bytes for local variables. Maximum is 2048 bytes.
Low memory available, stability problems may occur.
An error occurred while uploading the sketch
Invalid version '1.04' for library in: D:\Documents\Arduino\libraries\arduino_uip-master
Invalid version '1.04' for library in: D:\Documents\Arduino\libraries\arduino_uip-master
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x9f
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x9f
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x9f
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x9f
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x9f
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x9f
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x9f
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x9f
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x9f
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x9f
Problem uploading to board. See www.arduino.cc/en/Guide/Troubleshooting#upload for suggestions.
Invalid version '1.04' for library in: D:\Documents\Arduino\libraries\arduino_uip-master
Invalid version '1.04' for library in: D:\Documents\Arduino\libraries\arduino_uip-master
First remove your arduino from the module and program it, ( sometimes modules use TX and RX pins of arduino which prevent arduino to code when connected)
If it doesn't works for you, simply try to bootload your Arduino!
Thank you for subscribing to Mission Critical!
I try to operate different sketches for lighting to ON a number of LEDs, but this board of nano can only handle 4 LEDs per sketch and no more. Is there a solution? Thank you.
Help me about the missing botloard thank you!
Thank you for subscribing to Mission Critical 😊
Bro if we do like the fourth process we can uplode the program with the use of uno to nano ha bro...?
Yes absolutely!
hi, I am using arduino nano and could not get rid of the problem .
Here is Problem below.
Sketch uses 930 bytes (3%) of program storage space. Maximum is 30720 bytes.
Global variables use 9 bytes (0%) of dynamic memory, leaving 2039 bytes for local variables. Maximum is 2048 bytes.
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x28
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x28
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x28
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x28
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x28
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x28
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x28
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x28
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x28
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x28
Problem uploading to board. See www.arduino.cc/en/Guide/Troubleshooting#upload for suggestions.
Invalid library found in C:\Users\Habib Daood Rathore\Documents\Arduino\libraries\sketch_dec11a: no headers files (.h) found in C:\Users\Habib Daood Rathore\Documents\Arduino\libraries\sketch_dec11a
Invalid library found in C:\Users\Habib Daood Rathore\Documents\Arduino\libraries\sketch_dec11a: no headers files (.h) found in C:\Users\Habib Daood Rathore\Documents\Arduino\libraries\sketch_dec11a
Change your USB cord and try again, thank you for subscribing to Mission Critical
Error is missing 'maintainer'
You have any solution.?
updated video coming soon, please be subscribed
Hi there
I don't have a UNO, so I couldn't do the bootloader step.
My Win 11 shows my Nano clone on COM 3, CH341 is installed, baud-rate: 9600
I've tried to make the Nano blink using the example in Arduino IDE 2.1.0 (also 1.8.19).
Board: Arduino Nano
Port: COM3
Processor: ATmega328P (ATmega328P old)
What I see is:
Using Port : COM3
Using Programmer : arduino
Overriding Baud Rate : 115200
avrdude: ser_open(): can't set com-state for "\\.\COM3"
avrdude done. Thank you.
Fehlgeschlagenes Hochladen: Hochladefehler: exit status 1
I've used four cables.
Any advice? Thanks in advance
i tried everything but im still having the error *error ocurred while uploading the sketch* so help please
i faced a problems on the pins of A6 and A7 on arduino nano once i program using those pins especially on simple blinking and keypad interfacing using those pins but doesnt give an output but once i use other pins they work perfectly, how to solve it?
A superb video - your 'Burn Bootloader' information sorted my cheap Nano problem in no time. Thankyou Mr Mission Critical, you are a STAR Sir!
hello, i m getting an error as "programmer is not responding". Can u help with it? It's really urgnt.
I think you already got your Error fixed! Yet if you face any issue, feel free to comment down! Thank you for subscribing to Mission Critical
Bro! On my nano as i pug in usb all led lights (rx,tx,and power)starts to glow except (L) labeled led .my pc and mobile shows no arduino board found ...please help me out..nano was working recently...please help
I think you burnt your Arduino officially, did you short circuited or may be applied over voltage or something to the board, if yes, it might be damaged else it might be a defective board,
Thank you for subscribing to Mission Critical
Hi bro
I have an Arduino Uno clone. I had the 2nd problem. But I solved it.
Now I am facing the 3rd problem.
Arduino Uno board is not displaying in my boards list. How can I fix it...?
The process is exactly same for arduino uno
i purchased arduino uno clone ,i installed ch340 driver but when i connect the board nothing happens in my laptop ,even no connection notification no popup no port in device manager and no port in IDE but all 4 leds are glowing
what should i do plzz help!!
i got 20 of the nano's and i get this on almost all, almost the same error, can you give me some advice?
Arduino: 1.8.13 (Windows 10), Board: "Arduino Nano, ATmega328P (Old Bootloader)"
Sketch uses 1692 bytes (5%) of program storage space. Maximum is 30720 bytes.
Global variables use 204 bytes (9%) of dynamic memory, leaving 1844 bytes for local variables. Maximum is 2048 bytes.
avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0xfc
avrdude: stk500_initialize(): (b) protocol error, expect=0x10, resp=0xfc
avrdude: initialization failed, rc=-1
Double check connections and try again, or use -F to override
this check.
the selected serial port
does not exist or your board is not connected
Brother, is there any system to upload bootloader to Arduino Nano using downloaded software from internet without using another Arduino?
Hi bro help me :( my arduino uno don't upload:
An error occurred while uploading the sketch
avrdude: stk500_paged_load(): (a) protocol error, expect=0x10, resp=0x00
avrdude: stk500_cmd(): programmer is out of sync
avr_read(): error reading address 0x0000
read operation not supported for memory "flash"
avrdude: failed to read all of flash memory, rc=-2
avrdude: stk500_disable(): protocol error, expect=0x14, resp=0x00
Hi in my clone one problem is happened like when ever I connect to the power or laptop its light blinkes and off and it happens again and again...Please help with a solution.
their is no port issue or code uploading issue only it connect and disconnect.After uploading the code it does not runs the light blink and off.
I don't under stand what to do now because no where I don't get this problem solution.
Hi, I am having problems with new nanos. I need the old loader versions, which work perfectly for me. Is there a way to know when purchasing them, or can I use this method in the video, to upload the old boot loader onto a new boot loader?
Error while burning bootloader.
avrdude: Yikes! Invalid device signature.
Double check connections and try again, or use -F to override this check.
An error occurred while uploading the sketch
i did all of the tips that you did but still no works
Try changing USB wire ,
Thank you for subscribing to Mission Critical
@@mission_critical but my computer recognize the nano
Then, could you please explain the error?
I just select arduino NANO as board and click the respected COM and uploaded a simple sketch BUT the compiling REAAAALLLLY takes forever to upload and after 3mins or so the arduino IDE is displaying error about that simple sketch and i dont know what to do cause i need that board for my next proj
Try to disconnect everything on the board, just connect Arduino board, without any connections and try again, if it still doesn't work, try to change baud rate to 9600
when i plug in my ardruino nano into my computer it says that the device isnt working properly i have tried switching out cables
planning to make an updated video on this soon, be subscribed to not miss that when its aired! thank you
What this error is about? i can''t upload my code into Ardunino nano
Arduino: 1.8.10 (Windows 10), Board: "Arduino Nano, ATmega328P"
Sketch uses 892 bytes (2%) of program storage space. Maximum is 30720 bytes.
Global variables use 9 bytes (0%) of dynamic memory, leaving 2039 bytes for local variables. Maximum is 2048 bytes.
Error downloading downloads.arduino.cc/packages/package_index.json
An error occurred while uploading the sketch
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x72
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x72
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x72
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x72
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x72
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x72
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x72
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x72
avrdude: ser_recv(): read error: Access is denied.
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x72
avrdude: ser_send(): write error: sorry no info avail
avrdude: ser_recv(): read error: Access is denied.
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x72
avrdude: ser_drain(): read error: Access is denied.
This report would have more information with
"Show verbose output during compilation"
option enabled in File -> Preferences.
This doesn't looks like arduino problem, i would suggest you to uninstall and reinstall the arduino app and then try with blink code first
I followed the instructions, and everything was going fine up till the point where I attempted to burn bootloader to the nanoboard. I'm having an error that just says this:
keep getting this error
avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x1c
have checked board is conected in device manager and is on comport 3. but still struggling
Try to change the usb wire
It's really weird, i have 2 Arduino Nano clones, and i have really weird values on analog pins (even the pot read example throws weird values when moving the Arduino/wires around).
I didn't flash anything/installed the CH340C drivers cause they got recognized as soon as i plugged them in my computer.
Also i'm sure my pots are okay i tested with a multimeter, maybe bad AliExpress wires or just the board itself having problems
Hello to Mission Critical. I really appreciate your video on how to fix nano issues. My nano gets heated (chip) once I connect the usb to the pc with no load, and it does not upload the sketch. Can adivise with that ?
Avrdude: attempt 1of 10
.
.
.
What should I do for this error???
Try changing usb wire else check connection
Hey, i found one solution for this problem, can you first try to upload the code and then connect the circuit. / Device, please let me know if it works for you
@@mission_critical it dint work thou😐
@@pavano6970 i think your USB wire must be broken, try changing it? and also give your computer a restart may be
When I upload my code my computer crashes.. any idea what’s going on there?
I think there must be some problem with your hard disk on computer, definately not Arduino problem, this is simply not possible for Arduino to crash your pc, definitely get your pc checked
when i upload any program to my arduino uno r3 its showing error can you help me out !!!!! please
I got an type c version of clone, even after uploading bootloader it doesn't work
Can i change bootloader with clone nano like arduino uno?
My ardiuno nano board is working already but now not working . boot loader not working proper.
power led is working . uploading is working very slowly. uploading files is not working
I think you officially burnt your Arduino board, this happened to me too! I accidentally shorted the Arduino 5 v with 12v supply, and then ic completely stopped working!
Still just to make sure,why don't you try changing the usb wire, it solved 90% of the peoples problems for this issue !
Thank you for subscribing to Mission Critical
*Thsnk you sir, I switched to ATmega328p(Old Bootloader) and my nano worked!?* btw What are the bugs on the "old bootloader" you speak of.?
Hi I am used Arduino Nano in my project, it some times hanging , my code size is around 10k and sram is around 885 bytes is used
please, my Arduino Uno is not working, I upload the code but is says 'uploading' but it doesn't says 'done uploading'
I am trying to upload code but I get this:avrdude: jtagmkII_getsync(): timeout/error communicating with programmer (status -1) then executing command oh and also I have a lafvin nano
I think you need to select Arduino nano old bootloader
I'm having the same problem with nano clone, COM4, Programmer: ArduinoISP
avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x28
avrdude: stk500_recv(): programmer is not responding
When I select ATmega328P Old bootloader, it gets uploaded (blink) but delay(1000) = 1 second is more like 4 seconds.
Any idea what might be the reason for that?
Thanks.
avrdude: Yikes! Invalid device signature.
Double check connections and try again, or use -F to override
this check.
Failed chip erase: uploading error: exit status 1 I got these error wfen i click burnbootloader
when i connect nano to pc it always shows your device is not working
Part 2 coming soon, be subscribed
Went through each step and still cant get my nanos to upload the ide consistantly. I usually see this error:
avrdude: ser_open(): can't open device "\\.\COM3": Access is denied.
Problem uploading to board. See www.arduino.cc/en/Guide/Troubleshooting#upload for suggestions.
I've gotten the nanos to work a couple times, but they will usually show that error message. After installing the drivers and burning the bootlader with my uno, even the uno will show this error message at times. Any thoughts?
updated video coming soon, please be subscribed, thank you
Thank you very much! I had to do the bootloader burn on my 3 that I got 2 weeks ago. I couldn't upload anything, and got frustrated, and now they're working like a charm 😋 thank you!
After i upload the code in nano all things works perfectly but after connecting it to my circuit it automatically erase the code in it pls help
Thank you so much. This video helped me finally finish my project!
Glad I would help 😊
Taking too long for uploading and at the end it is showing error
When i erase the codes then also showing the same any solutio???
Part 2 of this video coming soon, which will solve most of these problems, be subscribed
its comin within this context on lcd.init ( ); please reply what to do
Please refer to my LCD tutorial, and first clear the basics there before proceeding to this project, and please feel free to comment and share for any confusion further
Nice video
I want to connect arduino nano(with circuits) to multiwii drone pc app for project
So plz suggest me
Should i buy Ch340 nano arduino or else which?
And how to know that it is not a clone
Um, first factor is cost, look on Arduino website, and the cost of Arduino Nano that you purchased, second thing original Arduino never has ch340/ch341, because it uses FTDI, and I didn't understand your first question, what do you want to do with multiwii drone pc app?
@@mission_critical
Thnx for reply
Multiwii is a online open source platform to build drones(quadcopters)
Okay, so your question is?
Is there any feature difference between these two ?
Like drivers or connections
No, clone is exactly similar, if you are careful enough, you would easily use this clone for years, and yes I saw the multiwii flight controller, you can use Arduino Nano and Nano clone for that as well✌️
i did every thing but still i is not showing the proper com port
Getting error
No sound when we plug in Arduino nano to computer
no device found under device manager
only one port is visible in Arduino
all settings (ie. seleting arduino namo, selecting atmega32 etc.) are perfect
still getting error
--------------------------------------------------------------------------------------------------------------
Global variables use 331 bytes (16%) of dynamic memory, leaving 1717 bytes for local variables. Maximum is 2048 bytes.
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x30
avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x20
avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x30
avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x20
avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x30
avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x20
avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x30
avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x20
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x30
avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x20
An error occurred while uploading the sketch
any solution??
My error box show error getsync500 attempt 1 on 10 etc
You should try to disconnect the circuit and upload the code first, also try to check for bootloader issue
Bro,my nano wasn't upload. I connect servo vcc to nano Gnd and servo gnd to nano vcc.and l upload. Next time it not uploaded. Pls give reason and soln
Hello there, can you please Message on Instagram, I am not sure how well could I help you in comments section, you can find link to my social media in video description
officialmissioncritical
When I upload my codes in Arduino nano with phone I face a uploading error
How to activate dfu mode on nano board
I cant use tx and rx on my clone, i tried the echo test
You might have connected those pins to some other device, try disconnecting Arduino and then try the echo test
Code is uploaded but program is not running
In my aurdino nano L led is blinking after connecting
kabhi kabhi hi port dikhata hai aur maximum time port show ni kart.. to fir kya kia jaye sir??
This video really helped me and saved me from spending money on a new board thankyou
i boughta cheap arduino nano for school project but it didnt uploat first and now it works. thankyou
Thanks a million. I finally got it to work after the 4th step.
You, master. I was about to return the boards to amazon. Thanks!!