Видео

It's then shipped to Walmart to be sold as "handcrafted" kitchen knives

My motor is just beeping and not spinning. What do i do?

Hi i did as you said but it’s not uploading and keep showing me this errror: avrdude: stk500_recv():programmer not responding Avrduded: stk500_getsync() attempt 10 of 10: not in sync: resp=0xa1 Please help me I’m going insane

This is very old torchlight bulb

hello sir, im already sett the baud rate same as coding, but after i send AT, it doesn’t show any response. May i know whats the problem ? the connection i think okey because it blink once every 3 second

I can't install it. It keeps saying Failed to install

please share code

Can we ise for a month without register it and use in Gas leakage project to recieve sms?

I asked a doubt to you But you not respont😢

Max RPM??

I want this product I send amount can u send me please 😢😢😢

Soldering iron link ?? Each Battery cost and purchased from ?

also which sim can i insert coz i was inserting a 4g jio sim and also many people are saying that it only supports 2g sim plsss reply we are making a project 4th year polytechnic

so my gsm sim900a looks different why is it so also it requires a 12vdc and after putting the sim the network isn't showing and the network led is continuously blinking

possibal 8 segments display work sar ???...🙏🏾🙏🏾🙏🏾

Sir is the GSM SIM900A module support 4g sim?? Please reply sir

nice🥰🥰🥰🥰

Legend. I had to turn the POT to adjust the contrast. I was going crazy! Thank you so much.

Thank you bro!!!! You are our lifesaver!!!!!!!!

Sir what is the issue if we power our gsm module through 5v output of arduino?

sir i ran a code to send data to thingspeak ,and it is showing cpin?---> error,,,can u suggest any solution please

avrdude: Yikes! Invalid device signature. Double check connections and try again, or use -F to override this check. Failed chip erase: uploading error: exit status 1 I am getting this error, how can I fix it?

how do I get the software

great project only one thing can you please tell how to do this on a 7 segment display using 6 such segments

Can we use mini usb to connect programmer module with our laptop

dude you're the best

Thank u 🙏

Jaldi sa comment kar da ta like milanga 😂😂😂😂😂😂😊😊😊

Please dear code

Please program and diagram

amazing this has just saved one of my arduinos stuck on a serial flood, nice video well explained

Very simple and usefull instruction, but it didn't work for me. Timeout connection. Then I check few instructions and add one detail. I connect RESET pin to GND for change UNO mode to UART. Now it works perfectly. Thak you very much! Hope this comment will helpfull.

So, most of batteries are fake then 🤣🤣🤣

hi programme pliz

Thanks for this video

thank U so much now its working for my Ardunio Leonardo with CANBUS module and i add this code to the empty sketch #include <SoftwareSerial.h> SoftwareSerial BTSerial(10, 11); // RX | TX void setup() { // Start the hardware serial for debug messages Serial.begin(9600); // Start the software serial for communication with the HC-05 BTSerial.begin(38400); // Default baud rate for HC-05 in AT mode Serial.println("Enter AT commands:"); } void loop() { // Check if there's data from the hardware serial (debug) if (Serial.available()) { String command = Serial.readStringUntil(' '); sendATCommand(command); } // Check if there's data from the HC-05 if (BTSerial.available()) { while (BTSerial.available()) { char c = BTSerial.read(); Serial.write(c); // Show the response on the serial monitor } } } void sendATCommand(String command) { command.trim(); // Remove any accidental leading/trailing whitespace command += " "; // Append CR+LF BTSerial.write(command.c_str()); // Send the command Serial.print("Sent: "); // For debug Serial.print(command); // Show the sent command }

Kya hum directly 12v adaptor to niche Arduino pe jo adapter pin ka port hai uspe lga skte hai ?ya fir apke jesa hi karna padega? Koi difference aaega kya?

Bro can you upload clear picture about code

When try to upload the code it’s showing this message ‘classs Date Time has no member named ‘day Of Week’ . Please answer me. Please answer me.

can share code please

omg tks u so much

Pliss howto tft display eye

Showing I2C devices not found.Help me please

Not true

Do you have ready made kit of this project... If available...I want to buy it Please provide information as soon as possible

i have this error message : #error "Please specify your BLYNK_TEMPLATE_ID and BLYNK_TEMPLATE_NAME" i tried to include it and it doesn't work

Thanks so much

Thanks so much, saved my bricked Nano!

Sir in aim900a i can't get 2g sim what i do where i get 2g sim can it work in 4g sim

What was the WHOLE extra device that was not in the schematic or listed in the annotations.....................................