Why Wont My Winch Free Spool?
HTML-код
- Опубликовано: 26 авг 2024
- A quick how-to video that might help you figure out why your winch wont freespool.
www.bleepinjeep... - All the best Off-road videos of RUclips in one spot without all the boring stuff - Updated Daily!!
nice job, and to those worried about taking the grease out, I spoke to mile marker 3 years ago, and they told me to go in an remove the grease, they said what happens is people over work the winch (guilty) and take it beyond its duty cycle and liquefy the grease, then it re solidifies all in the bottom and makes it near impossible to free spool. He actually told me I could use a heavy weight gear lube oil since in the north, if in the south do a light-fair coat of synthetic grease. solved my problem. As for those worried about water, check your seals and you should tear your winch down every couple years and re grease anyway... Thanks man, I meant to actually do a vid on this but never got to it.
on my smittybult i dont think the problem was too much grease but rather low quality unstable grease that thickens too much over time to more of a waxy state, i removed all of the cheap grease with solvents and replaced it with standard black molly wheel bearing grease packed as much grease in as i could and years later now it still free spools like a champ.........so its not quantity of grease that matters, its quality of grease.......................bad grease is the problem, i recommend to use a lot of grease when you repack............these winches are made in china so your getting bad chinese grease when you buy them.............
+Ocean House your probably right, the cheap stuff hardens up.
I will pay you $5 to say "WE GOT ALL KINDA SHRIMP. DEEP FRIED SHRIMP. BBQ'D SHRIMP. CAJUN SHRIMP..."
It is called a planetary gear set. Fill it to 60% with AeroShell 22 and every Six months (if not used) pull out the cable and respool it to keep the gears coated.
If you squirt a little lot of motor oil in there, the oil will soften the grease, making it free spool without any more disassembly. Heck, you may be able to remove the selector and add oil through the hole.
Thank you for your video. I have the exact same prob. with my Jeep winch. Now know where I start to take a look in there and see what's going on. I have not been able to pull out my cable in free spool since I bought it new. I am guessing I will fine exactly what you did and that will be to much thick grease. I will do this tomorrow. Thanks again.
Like the tool-belt.... Nice touch!
Just got a off brand winch off amazon and it was so greased up from the factory she would not free spool. Thanks for the help!
Greasing up the bushings on each end of the spool sure helps as well.
Thanks a lot man this worked with mine, so I had to celebrate by going mudding
@fordpower6973 When your winch has never free spooled for six years and it finally does, you will get excited and pull all the cable out. The leather gloves will keep you from getting splinters when spooling it all back in;)
I think XJs are one of the only vehicles where all of their owners use the hoods as workbenches. When i'm working under the hood, my winch bumper sure comes in handy as a workbench!
for sure... live and learn
that is one of many things on my to do list... hopefully in the near future!
some people call that a dovetail. I just cut and hacked and then bent them in. I thought about doing a vid on it but I only have pictures and not that many.
Nicely done video, great sense of humor, got your point across just fine. Thanks for sharing! Bet you wished you'd dove in to that winch gear box six years sooner =)
if oil can leak out then water can come in. that is probably why the manufacture packed so much in there to counter any water intrusion.
that thick grease was high pressure grease so the gears dont wear out to fats for warranty purposes but thin grease will be much easier to pull the cable now yes its a good way i do sam to my winch
All grease gets dry over time from heat cycles. Same thing in when bearings. The grease just breaks down. People don't realize this. Probably just a good cleaning and new grease. Don't forget, grease not only lubricates but helps to cool also.
WARN HAS WORKED FOR 90 AWESOME EVERYTIME!!! 75 CJ5 Out
Tie the winch hook to a tree and drive backwards as fast as you can, this will free up the spool in no time - saves having to wear those rubber gloves.
Tried it, Didn't help mine so I am taking it apart for a good cleaning and new lighter grease.
What weight of grease is very important also !
Thanks for that.
It's a Domin8r X from the supercenta, thats why.
You fixed the problem without knowing the EXACT cause the problem (you sprayed oil inside the gear housing). The actual problem is thick grease between the gear housing cover and the clutch gear; there should NOT be any grease on the outside of the clutch gear and the inside of the gear housing, this is where you should use light oil. For the best explanation of this, see ruclips.net/video/CyYs-oKlxUE/видео.html between 21:20 and 22:50 minutes (It's a different brand of winch, but they are all the same in this regard)
This comment needs to be pinned to the top. About 10 years ago I cleaned and greased my winch after it got submerged and I used "Green Grease" all over everything in the gearbox including the outside of the engaging collar. That's the thickest, stickiest, nastiest grease I've ever used and I could barely get it to freespool by hand afterwards. This weekend, I pulled it apart again and used moly grease on the gears and some thin air tool oil on the outside of the engaging collar and it made a night and day difference.
Awesome page with great how-to's. Many of the short cuts are ones my dad taught we as a kid...I have a similar issue except I can't even get the free spooling knob to turn at all and I end up having to use the winch to free wheel. What do you think that could be? Thanks in advance!
thanks
could you put oil of some kind in there that's thinner than grease but will still lubricate?
Great videos man! You sure are smart when it comes to jeeps.
Hey guys I have a waren 4500 free spoll and it 3 is mouths old used 3 times . took a ride out today and it is stuck in the pull in position I can't turn in release the cable any suggestions my atv is stuck in the woods
something must be jammed up or rusty inside there.
ya, just like most products they are all made by the same company with different stickers on the front.
How did you reroute the wiring for the winch
And wave your majic wand to the right. Not the left. And everything just jumps back in place. So easy
What? Ive been busy... no really I thought it was just broken, or I was just to weak to pull it out;)
how did you concave your front fenders in ?
What if u cant get it to switch over to free spoil
What was the welding glove needed for?
My Warn lever won't even shift into freespool mode. Any suggestions?
My warn 3500 vantage is a pos, it takes 10 min of playing to engage back, i hate disengaging it in fear of noy engaging back
maybe, but it would probably leak out
You're like a jeep Bob Ross
Take it apart, I bet you'll be able to see the reason and fix it fairly easy.
so it looks like you were are a lineman for the county.
Thanks Bleepin Jeeper! Sounds like a problem I'm having with my 12000lb er.
Mine is working great now thanks for the video
Hey, can I do this with my diffs and transfer case too? I think I would get extra gas mileage if I took all the thick oil out and just sprayed wd-40 in there before I take it out every time. Ha ha.. just kidding buddy, but food for thought. Do you think it will really be a good idea to take all the lube out of your winch? You'd probably want to check it often to make sure it doesn't get contaminated with water and/or go dry. High pressure grease is in there for a reason.
I just got a warn 16.5 ti. No free spool. What do you think same problem ??????? WTF. It goes in and out fine with the remote but no free spool.
could also be the brake is malfunctioning i guess
Thick grease from the factory, Clean it out and apply new grease.
did that used to be a zj?!?!?!?!?!
that winch looks almost identical to the q9000 I have on my TJ... interesting.. makes me wonder if it's just a milemarker thats been rebranded
When you said "gummed" I knew you were from Appalachia
@TeamArsenal1036 Just not when it comes to anything else!
Hey man my problem in my winch is, Its very hard to switch the engage to free spool, what do you think is the problem? Thanks
I've got the same problem as the video and as juromebato. Hard to engage free spool. Won't free spool. And it makes a strange sound when winching in or out. Have you heard about this? Could it be that it got water inside or the grease is gone? It's mounted behind an ARB bullbar so i haven't got it removed so far.
jan585 sounds like something with the clutch, my warn does a similar thing but relieving the tension on the gears first (by spooling in or out with the controller) it works fine. If i half the lever halfway in or out it makes a funny sound too, so to me id say something has your clutch stuck, which could possibly be water which could now be corrosion
thanks man! this really helps a lot. more power!
an XJ
I figured the "grease" in mine was like tar & saw your vid before I took mine apart. It's "tar" & there is 25 pounds of it! I heard The factory had a shit load of WW2 BUBBA GUMP sticky bomb grease & the employees were trying to make it dissapear
😅
Haha great vids man
You know they got shop towels for cleaning grease and stuff off
*controller to power unspool
chipmunk ?