Mate big props on really nice looking bar work, got me wanting to work on this type of stuff broaden my skills and knowledge, lots of maths going on there lol looks awesome works well
Loving the videos mate ! 5 stud hub conversion on the 80 is a nice easy way to have big axle studs and wheel studs to stop them snapping , classic crusier things
Awesome vid man, you've given me some motivation to get some work done on mine, I'd be keen to see a vid on gutter sliders/ roof sliders if your gonna put some on this truck
Thanks mate. This will definitely be getting gutter bars and a roof rack. But there’s 2 spots in the gutter that need repairing before I put them on. So the video won’t be out for another couple months. Cheers
Awesome work mate keep it up! Don't skip on the fine details I'm learning a lot I had a crack at bar work on my gu. not bad for a first attempt but definitely going to re do it at one stage so all this is helping.
Wurth do some mint tap sets that have nice small shanks fit in the drills sweet as and the 3 steps for each size make it prety fast and less chance of jamming 👌👌
Technically you can’t here either unless it’s under the guidance of an engineer and it gets certified. I had clamp on style before these ones and they are so much easier haha!
Howdy fulla love the tube bendin! Mint work.... i really enjoy watch!! Love learn new ways of mountin sliders and things like that. im convertin mi tb42 carby to efi.... im just strugglin to find info on ls1 coils and how to wire them up.... do they go directly to the my helteck ecu?? Or do i need a tb42 efi dizzy??? Could you do a 5min vid on how yours is setup? Chz
Hey mate, thanks for checking it out! You need an ecu that supports direct fire ignition, in the ls1 coil there’s 4 wires, 2 are earths, 1 is a signal from the ecu and one is 12v power. Use the positive from your coil and chain it together for the 12v, link the 2 earths together and put them to a good earth point, and then the signal goes straight into the ecu. You will need the efi dizzy for the cam angle sensor for the ecu.
![NOSFERATU - Official Trailer [HD] - Only In Theaters December 25](http://i.ytimg.com/vi/nulvWqYUM8k/mqdefault.jpg)
You could legit do a video on watching grass grow and still make it entertaining haha! Good stuff, keep it up 🙌
Hahaha, thanks mate, I appreciate that.
you make it all look so easy and top quality work, love all your stuff, so casual and down to earth too, thumbs up from me
Thanks mate. Appreciate it, I just try and be myself haha! Cheers
Mate big props on really nice looking bar work, got me wanting to work on this type of stuff broaden my skills and knowledge, lots of maths going on there lol looks awesome works well
Thanks for the support mate, it’s good fun figuring it all out! Cheers
More videos like this, there’s plenty to learn and you do a good job of it.
More to come haha thanks mate
5 stud wheels so 105 series diff conversion or something like that
Just the hubs mate, but spot on!
105 run bigger better studs for the axles and shit. Or something im pretty sure.
Exactly what I was about to say.
I really do enjoy these build vids and the days out on the tracks. Keep them coming please.
Appreciate it mate! Thanks for watching
Keep the content coming brother, it's gold👍
Thanks mate. Appreciate it
i love what your doing ! thanks
Thanks mate
Love the sliders
Thanks mate
Great stuff, a good watch.
Thanks mate
you my friend are an ideas man i love your barwork setup and your way of reheating pizza keepthem vids comming
Haha thanks mate. 🤙🏻🤙🏻
Bar work is looking sick, I do love the idea of inverted sliders for greater protection 👌🏼
Thanks mate, sliders this way is definitely the go!
Daniel Kistler for sure dude
Loving the videos mate !
5 stud hub conversion on the 80 is a nice easy way to have big axle studs and wheel studs to stop them snapping , classic crusier things
That’s it mate. Thanks.
Looking unreal mate
Thanks mate
Pizza on the press is livin barry. 👌
Bloody oath it is haha
Those wheels on the 80 look madd
They do look good!
Bloody good vid Daniel, great style barwork. Pipebending is a real skill it would be great to more. Cheers fella
Thanks mate.
Just about to buy another gq myself so watching these video's is awesome!
Give you some inspiration haha! Cheers mate
@@DanielKistler haha bloody oath, Cheers mate love your work!
Thanks for watching mate
love the shed vids content is prime mate keep it going
Thanks mate!
awesome work Daniel, the bar and scrubs look great, very time consuming
Very very time consuming! Thanks mate
Great work man, love these videos
Thanks mate
q bus is looking good mate keep it up
Thanks mate
Thanks for the great vid! Nice FTE on the engine stand 👌
Thanks for watching mate
Awesome vid man, you've given me some motivation to get some work done on mine, I'd be keen to see a vid on gutter sliders/ roof sliders if your gonna put some on this truck
Thanks mate. This will definitely be getting gutter bars and a roof rack. But there’s 2 spots in the gutter that need repairing before I put them on. So the video won’t be out for another couple months. Cheers
Awesome work mate keep it up! Don't skip on the fine details I'm learning a lot I had a crack at bar work on my gu. not bad for a first attempt but definitely going to re do it at one stage so all this is helping.
Thanks mate. I’ll do my best to put as much info as possible while still keeping it interesting haha! Cheers
How goods a shed skid love content keep it up mate
Haha shed skids are mint 👌🏻👌🏻 thanks mate
Cracking clip Mate
Top clean looking job!
You make dodgy look Pro 👌
Up the 80 🤙
Thanks mate
Walker evans beadlocks on the 80, nice rim.
Definitely a nice set of rims. Same as what he had before just different colour and stud pattern
Wurth do some mint tap sets that have nice small shanks fit in the drills sweet as and the 3 steps for each size make it prety fast and less chance of jamming 👌👌
Good to know. May have to check them out! Cheers
@@DanielKistler no drama bro love the vids 🤙
@@hotaxi701 thanks mate
any hot tips for tube notching? love the vids mate
Thanks mate. No real hot tips other than practice and understanding the angles. It takes a bit to get good at it.
Can't weld to the chassis in NZ .we have to clamp it into place which is even more work
Technically you can’t here either unless it’s under the guidance of an engineer and it gets certified. I had clamp on style before these ones and they are so much easier haha!
Man looks mint. What winch is that? How many lbs.
Looks mint.
What winch and how many lbs?.
Love this stuff fella. 👍🏼
It’s a red winch mate. No idea how many pound, would be somewhere around 8000 depending on gearing and voltage input. Cheers mate
great watch ol boy. ps what HD valve springs and valve stems do you recommend for the tb42s
Thanks mate! I use crow cam stuff in mine. Genuine valve stem seals and head gasket.
@@DanielKistler cheers champion, where you getting the genuine seals from ?
Rims are 5 stud instead of 6
Nice vid mate
Spot on mate. Cheers
If the die on the JD says say 167, do you put your tube 167mm before the bend at the start of the die?
Haven’t looked to closely at the dies lately to see what that number is in reference too so not sure mate
Hi we’re did ya get the “camburg” interlocking tube connectors? From camburg? Or are there other options??
Hey mate, just search camburg joiners on eBay or google, they may also be called roll cage joiners.
THE BEST WAY IS TO RATTLE GUN THE BOLTS IN M8
More Ugga duggas
@@DanielKistler send it like a gigglepin
@@jimmyd6819 hahahahaha
🙋♂️ the new rims for the 80, I can see what's different! Do I win another hoodie?
Your too late. Someone beat you to it hahaha
@@DanielKistler Kistler hoodies for everyone then
@@rustysranch2049 maybe one day hahaha
Is he changing the hubs just to suit those wheels or is there some other benefit?
Changed hubs so he had to buy 5 stud wheels. There are benefits to going 79 hubs but I don’t know them hahaha!
Loving the videos man! Quick question what size tube did you use for ya sliders/barwork?
Thanks mate! It’s all made out of 32nb tube. There’s a little bit of 25nb in there but not much
@@DanielKistler cheers bud! Yeah I’m gonna have a crack at fabbing up a set of sliders for my cruiser
@@reecemorris7676 nice mate! It’s good fun having a go!
@@DanielKistler definitely way more satisfying building it yaself!
Loving the videos mate 👌 what’s the story with the 80?
Thanks mate. It underwent some upgrades haha I’ll try do a run down on it!
@@DanielKistler 1fz turbo? Please do!
@@lochlinbyrne nah it has a ls1 in it at the moment.
80 series = 6 stud, but new wheels are 5 stud
Spot on!
Howdy fulla love the tube bendin! Mint work.... i really enjoy watch!! Love learn new ways of mountin sliders and things like that. im convertin mi tb42 carby to efi.... im just strugglin to find info on ls1 coils and how to wire them up.... do they go directly to the my helteck ecu?? Or do i need a tb42 efi dizzy??? Could you do a 5min vid on how yours is setup?
Chz
Hey mate, thanks for checking it out!
You need an ecu that supports direct fire ignition, in the ls1 coil there’s 4 wires, 2 are earths, 1 is a signal from the ecu and one is 12v power. Use the positive from your coil and chain it together for the 12v, link the 2 earths together and put them to a good earth point, and then the signal goes straight into the ecu. You will need the efi dizzy for the cam angle sensor for the ecu.
Rito chz m8! So i wont need dizzy?
@@sambriggs3194 yes you’ll need the efi dizzy for the cas.
Going to 105 stud pattern for the walkers ?? I run the walkers and 105 diffs under my Ute
Yep spot on!
Are you running 40nb tube?
32nb mate
Cracka vid mate! what's that fte gonna end up in?
Thanks mate. No idea yet, it’s my brothers.
Another yes vote for shed vids.
Haha more shed skids!
What finish are you going to use? Galvanise and powder coat?
I’ll just be painting it in 2 pac black
they are 5 stud
Correct
80 series are 6 stud not 5??
Spot on
105 series hubbys
Spot on!
Thats m14 5 stud 100,79 stud pattern on those rims
That’s the one!
@@DanielKistler do you know where he brought the walkers from.iv been chasing some for my 100 v8
Any chance of getting those scrub bar measurements
I thought I put them all in the video. Maybe only the degrees.
@@DanielKistler unless you want to make me some
@@td42times62 yeah I could do that
@DanielKistler how can I contact you privately
5 stud🤣
There 5stud not 6 for 80series
Spot on mate!
5 stud and 80 is 6
Spot on mate
Just watching you finish your rock sliders. Since you loved the job. Don’t spose you’d make me some for my 60
Joking mate but looks good
@@robcantwell1981 hahaha it’s not a fun job. The bender and that isn’t mine so I don’t really do work for others mate.
All good mate I was stirring. I like them but already have some and am in SA.
Cheers
5 studs
What’s the go with that banging noises in the background
Can you tell me when In the video so I can listen haha??
5 stud not 6 stud
That’s the one
Nice work dude what size tube you using to make the sliders etc cheers
Thanks mate. It’s all made from 32nb tube. Medium wall!
@@DanielKistler awesome thanks dude appreciate it, look forward to the next vid 👌
Thanks mate