I just received an International 2444 and that video was very informative. That almost looks like mine. I had no idea how the two stage worked but after this video I have the confidence to change it if ever needed. Thanks.
Thanks for explaining things. My clutch was removed without the transport bolts and I often wondered what they were for. I'll order some and get the tractor back together in the next month, hopefully.
Thank you so much for the video!! It was a major help. I was able to replace the clutch and pto discs in my tractor. :) A few tips to those who might read the comments for additional info. Move the front of the tractor, not the back, MUCH MUCH easier. DO NOT FORCE THE HALVES TOGETHER. You will damage the PTO disc and possibly the clutch pack. Packs are not cheap. While you have the tractor apart, become intimately familiar with the insides. It will come in handy to know what you're touching without seeing as you're putting it back together. As you bring the two halves together, continuously feel through the inspection cover and make sure things are lining up ok. Use four 7/16" x 8" course thread bolts to line up the tractor. These will act as guides to help line things up. Using a rolling floor jack capable of 24" of lift is very helpful.
40yeartrucker I tries moving the back first also. It is MUCH MUCH more difficult to put back together. I had to but a whole new clutch pack because I damaged everything on reassembly.
I love your shop Dave, just like mine, an abundance of natural light. Not nice yesterday -22C while I was swapping out the battery on my MF 255. Thanks again.
Thanks for video! It is just right, not a bunch of unnecessary music or telling everyone an hours worth of jibber jabber that has nothing to do with the job. Awesome content! I have watched all of your Massey Ferguson videos that have to do with clutch replacement, I saw the way you adjusted the clutch peddle in this video, but I did not hear or see anything about an adjustment of the PTO/captive clutch disk. (I am not asking about centering it I know about that). Are there any adjustments for that or does it simply bolt in place as you have show and that is all that is needed? Thanks again for a great straight to the point video!
With a new clutch it should be adjusted ready to go. To adjust the PTO clutch you adjust the setscrews around the outside middle of the pressure plate to .080-.090 clearance. Thanks for watching!
Thanks for the video, it helped me with my Tafe tractor clutch replacement, last summer. I made a video on the adjusting of my clutch pack, hopefully I can help those who need a little help, like your video helped me, Thank you.. Kenny.
Another awesome video Dave, very informative! I have a 1962 IH B275 with dual clutch. When I try to snowblow the yard with a 6' snowblower, I can smell the PTO clutch even when it's just 6" fluffy snow, tractor not working hard. I'm guessing it's time to change the PTO clutch and while I have it apart might as well change both clutches, release bearing, pilot bushing and resurface pressure plates. If I don't plan on using the PTO since I now always use the front loader to clean the yard and I don't use the PTO for anything else, can I just leave it and not worry about it causing damage to anything. Thanks.
Very nice video Sir, my cutch freezes up, if the tractor sets for more then 3 months. It sat for 5 months, well you know what happened. Normally I can run the tractor down the road with the clutch pressed down in second gear, jump the break and it will break free. Not this time. So I figure, I have to manually separate the clutch with a crowbar, thank god for the inspection hole. I learned allot from you, thank you very much for your video.
I am glad you found my video helpful! The next time that you know you won't be using the tractor for a while, try wiring down the clutch pedal when you park it, may be able to avoid the problem this way. Thanks for watching!
Hey Can you tell me what is size and thread on bolts what you are using to lock that clutch before pulling it off flywheel. we have mm bolts here as normal so i have to probably order those..
I am not certain what size they are, I just saved a set that came with a new clutch that I had installed. I think the y take a 10MM socket if that helps narrow it down. Thanks for watching!
Hi Dave, My mother inlaw has a Massey 35 the clutch works fine untill you engage the PTO then it sticks and you either have to try and pull it out of gear or shut it down to stop. Is it just stuck and it will come good with a bit of work or is it stuffed?Thank's
Question: when I release my clutch, I get a chattering noise/knocking sound from the gear box, if I release it real slow sometime it does the noise and sometimes not, any ideas on this problem? Otherwise the clutch works fine, don't seem to be any hydrolic problem as I can tell. Thanks
I paid a shop to replace the the two stage clutch in my MF3165 (basically a 165) I now only have about half the clutch pedal travel that I had originally. The PTO never disengages and when the pedal is pressed, I hear a loud rubbing sound that I can feel in the pedal. The Clutch, Pressure Plate and throw out bearing are supposed to be new but I believe I'm hearing a bad or incorrectly installed throw-out bearing. I left the machine at the shop but they already have my check. They are telling me "it probably only needs some adjustment" I'm afraid something was damaged in reassembly or perhaps the wrong part was installed. Your thoughts HELP!!!
If you have less pedal travel it would not be going far enough to disengage the PTO clutch, there are 2 holes for the linkage on the clutch pedal, it could be in the wrong hole. The noise and bad feel in the pedal is definitely something that needs sorted out though, a seized release bearing can wear right through the clutch levers. Thanks for watching!
Hi Dave, its the transmission i'm assuming because it keeps driving along with foot on the clutch and wont stop but it only does it when the PTO is engaged other wise its fine. PS she uses the tractor a fair bit so it hasen't been sitting around.Thank's for your reply. Cheers
+Wayne Appleyard Does the tractor have live PTO (2 stage clutch) or transmission driven PTO? If it is transmission driven and running something like a bush cutter, the momentum of the bush cutter will push the tractor even after pushing the clutch pedal. With a transmission driven PTO you need an "over running clutch" attachment for the PTO output shaft. Its a little extension shaft that goes on the output shaft of the tractor to let the implement free wheel when you shove the clutch.
Hi Dave, I have an International 444 and the clutch pedal no longer depresses the clutch. I took the return spring off and the pedal just dropped down to rest on the foot board. I can move it up and down freely but it does nothing. The clutch works fine as I can start it in gear and the tractors moves fine. I can also take it out of gear and into nuetral by slowing the RPM but can only get it back in gear by killing the motor. I have not removed the plate yet to look up into that area. Seems like something has come loose. It has always worked fine. This happened all of a sudden. Any thoughts?
That sounds like either the clutch pedal shaft or the release bearing forks broke (likely the forks), pull the plate off the bottom of the clutch housing and you should be able to see. One other possibility is that the clutch pedal came loose on the shaft, but I wouldn't think it would happen that fast.'Thanks for watching!
I removed the plate and nothing was broken. The clutch pedal shaft had gradually, over time, slipped to where it no longer engaged the pressure plate when you push down on the clutch pedal. A fairly simple fix. I also made sure I had proper free travel. Thanks Dave. Like your videos.
I opened the same tractor but I have problem with pto when I press the clutch pedal pto doesn’t stop it has to be with the adjustments on pto disc?? Or something else
I have a 135 diesel 1973 vineyard industrial model massey ferguson, 8 speed transmission .non multipower and it needs A 10" 10 spline pto disc for the clutch Yesterdays tractor doesn't carry where do you find one
If you check out A&IProducts.com you can find a locate a local dealer through their dealer locator or any local tractor dealer should be able to get one for you. Thanks, for watching!
good video Dave! looks like you will be doing a front axle pivot video next? my question is on my 1955 TO35 without live power, this tractor was available with live bad an option... can I get live power by swapping in 2 stage clutch, or are there internal differences inside the case too? thanks Robert
hi thanks for the videos,I have a mf65 a4.192 none multi power.A ball from a bearing when through third gear and the bearing was replaced .Now third and reverse have a ticking noise . should the gears be replace or keep it working and wait till a transmission overhaul?
Hey Juan, I'm glad you are enjoying the videos, Thanks for watching! It would be a good idea to take a look. It's probably chips off a couple of gears, but if its missing teeth it could lead to gears piling up and breaking the transmission case.
thanks for the reply . I'm planning on a tear down soon.I would love to see a video on trans overhaul procedures to make things easier for many people. thanks from Mexico
Hello, nice video you made about clutch replacement!! I did the same job on my mf 35. You told in the video that it was you're second clutch plate because off put pressure on the first one. I'm afraid i made the same mistake. Can you tell me what exactly happend
THe owner installed the first clutch and didn't get it all the way together before he tightened the bolts, the spline hadn't started on the transmission disk and bent the hub in the disk. When he found he had trouble he brought it to me. Thanks for watching!
Dave, How do you remove the input housing on an MF65, American built, ser # 673,543. It is dual clutch like this video. you use one as the alignment tool. I thought the 4 bolts on the housing and the pto shaft and housing just slipped out. HELP!
You will have to push the bottom shaft to the rear out of the bearing till it drops down so there is clearance for the input shaft to come out. Thanks for watching.
Heya, my MF165 is making a knocking noise. When I took the clutch cover off the bottom it sounds like it's coming from that area. The knock does go away when I rev the old perkins to 100rpm. I'm thinking I will take the oil pan off and inspect the bearing mains. Driving me nuts but the tractor runs great and has good oil pressure. I was told to unbolt the inspection plates on both sides of the transmission (two bolts in a diamond shape), but I'm not sure if those hold anything internally?
The two small diamond shaped plates are the retaining pins for the hydraulic pump, the inspection plates are the round ones about half way up the sides. One or both of the retaining pins for the hydraulic pump could be broken which could cause a knocking noise, you would be able to see that through the round covers on the side. You will want to at least partly drain the hydraulic oil or it will spill out when you take the covers off. Thanks for watching!
I looked at it last night, sitting in the seat on the left is the cover the one with the PTO-Engine RPM, PTO off, PTO hydraulic? Those covers, there is one on the other side as well. I also notice that the fluid is milky so I have water in there some how! Ordered new shift booties, maybe the that is the issue. Just want to inpsect the pump to make sure, though.
Awesome Video. Purchased a Mf175 a few months back, the guy had told me that he put the pto clutch in 180 Degrees off. Is that possible? When I try to engage the pto it starts to grab at the end of the pto lever movement. Please help!
I am glad you enjoyed the video. It is possible that he put the disk in wrong side toward the flywheel, that certainly could make it grab. Good luck and thanks for watching!
I have the Massey 165 and it is a hydraulic lemon. It has the Multi-Power that doesn't work and the hydraulic outs don't work either. Liked your video tho.
Thank you so much for this vid..about to do the same job (different make but same two stage principal) I can see more than what was said at 6:08 when I try this lol
That would be the identical clutch to the one in this video, you don't see the 9" PTO disk because it is captive in the center of the pressure plate assembly but if you look close at the assembly you can see the spline hub of the disk. Thanks for watching!
have MF 275 TRACTOR (PRIOR TO 9A349239), I have followed your instruction and changed the clutch, now I am trying to put the wire back and don't know how to get power to the glow plugs. I see Deisel fume of the exhaust but no fire because I do not know how to get power to the glow plugs. The MF 275 wiring diagram does not show where the wires get connected to.@t?
Can anyone help me pls? I have a Lenar FS 254 II tractor. It's done hardly any work and went through a flood. Is been sitting for quite some time and the clutch doesnt seem to disengage at all. Is a two stage clutch. Could it be that it is rust stuck on the pressure plates and the transmission disks? It has three adjustment points and also three limiting bolts. I wonder after watching this if what I think is the limiting bolts should be undone a lot more. Can anyone point me to some instru tion on how to properly adjust this clutch? I would be grateful for any help. Regards to all. Florian
These tractors could have either single or dual clutch, but the flywheel and transmission are different between the 2. You can't change from dual to single or single to dual without changing flywheel and transmissions. Thanks for watching!
A 240 could have this 2 stage clutch or a single stage if it has hydraulic "independent" PTO. If you press your clutch all the way down to stop the PTO it's the 2 stage clutch. Thanks for watching!
When you press your clutch the hydraulic pump stops pumping. I expect that your lift cylinder is getting worn and scarred up so when the pump stops the oil bypasses and your lift drops. Thanks for watching!
+Israel Hernandez You can find the parts book online at partstore.agriculture.newholland.com/us/ . There is no instruction on the how-to side but you can see how things fit together. Just type in your model number in the search box.
165 could have single or dual clutch, 11 or 12 inch and with a dual it could be a 10 or 21 spline PTO disk, you won't know until you take it apart. Thanks for watching!
I just received an International 2444 and that video was very informative. That almost looks like mine. I had no idea how the two stage worked but after this video I have the confidence to change it if ever needed. Thanks.
The IH and Massey 2 stage set-ups are quite similar. I'm glad you found the video helpful. Thanks for watching!
Thanks for explaining things. My clutch was removed without the transport bolts and I often wondered what they were for. I'll order some and get the tractor back together in the next month, hopefully.
I am glad you found the video helpful. Thanks for watching!
Thank you so much for the video!! It was a major help. I was able to replace the clutch and pto discs in my tractor. :)
A few tips to those who might read the comments for additional info. Move the front of the tractor, not the back, MUCH MUCH easier. DO NOT FORCE THE HALVES TOGETHER. You will damage the PTO disc and possibly the clutch pack. Packs are not cheap. While you have the tractor apart, become intimately familiar with the insides. It will come in handy to know what you're touching without seeing as you're putting it back together. As you bring the two halves together, continuously feel through the inspection cover and make sure things are lining up ok. Use four 7/16" x 8" course thread bolts to line up the tractor. These will act as guides to help line things up. Using a rolling floor jack capable of 24" of lift is very helpful.
I am glad the videos were useful for you, thanks for watching!
Timothy Lawrence my Massey 30 industrial has a big loader to deal with so was going to move the back....
Mine slips because of not enough pressure there is free play ,is there any way to increase the pressure on the pressure plate?
Massey 30 ind.
That is a strong indicator that your clutch disk is worn out or oily, sounds like time to replace. Good luck and thanks for watching!
40yeartrucker I tries moving the back first also. It is MUCH MUCH more difficult to put back together. I had to but a whole new clutch pack because I damaged everything on reassembly.
I love your shop Dave, just like mine, an abundance of natural light. Not nice yesterday -22C while I was swapping out the battery on my MF 255. Thanks again.
+masseymm Yeah, great lighting but the roof leaks really bad! :) Thanks for watching!
Great video. I had to break and IMT-560 in half to rebuild the engine. The clutch was new but the pilot bolts are very important. Good deal.
I'm glad you enjoyed the video, thanks for watching!
Always like your tutorial videos, good job.
I am glad you enjoy the videos, thanks for watching!
Thanks for video! It is just right, not a bunch of unnecessary music or telling everyone an hours worth of jibber jabber that has nothing to do with the job. Awesome content! I have watched all of your Massey Ferguson videos that have to do with clutch replacement, I saw the way you adjusted the clutch peddle in this video, but I did not hear or see anything about an adjustment of the PTO/captive clutch disk. (I am not asking about centering it I know about that). Are there any adjustments for that or does it simply bolt in place as you have show and that is all that is needed?
Thanks again for a great straight to the point video!
With a new clutch it should be adjusted ready to go. To adjust the PTO clutch you adjust the setscrews around the outside middle of the pressure plate to .080-.090 clearance. Thanks for watching!
thank you so much you sure showed the easy way of doing it , that does not require sophisticated tools etc
I'm glad you found the video helpful, thanks for watching!
Great instruction, I'm learning about dual clutch on my 150.
I am glad you found the video helpful, thanks for watching!
Can you tell me how to properly adjust the release bearing singers?
Thanks for the video, it helped me with my Tafe tractor clutch replacement, last summer. I made a video on the adjusting of my clutch pack, hopefully I can help those who need a little help, like your video helped me, Thank you.. Kenny.
Hi Kenny, I am glad you found the video helpful. Feel free to link your video in the comments here.
Thanks for watching!
Another awesome video Dave, very informative!
I have a 1962 IH B275 with dual clutch. When I try to snowblow the yard with a 6' snowblower, I can smell the PTO clutch even when it's just 6" fluffy snow, tractor not working hard. I'm guessing it's time to change the PTO clutch and while I have it apart might as well change both clutches, release bearing, pilot bushing and resurface pressure plates. If I don't plan on using the PTO since I now always use the front loader to clean the yard and I don't use the PTO for anything else, can I just leave it and not worry about it causing damage to anything.
Thanks.
If you're not using the PTO and the transmission clutch works fine then you don't need to worry about it. Thanks for watching!
@@CanadianRedneck15 Thanks for the reply Dave!
Great video. Where did the shaft he used instead of an alignment tool come from? I missed that.
The shaft I used was an input shaft from a tractor I had scrapped.
Thanks for watching!
Thanks Dave for reply!
Fantastic video and very informative. Thank you.
Thank you, I'm glad you enjoyed the video. Thanks for watching!
What can I use to align the clutch disc's as I don't have a shaft like you used. Thanks heaps.
You can use a 3/8" extension and a couple of 1/2" sockets to get you there. Thanks for watching!
Very nice video Sir, my cutch freezes up, if the tractor sets for more then 3 months. It sat for 5 months, well you know what happened. Normally I can run the tractor down the road with the clutch pressed down in second gear, jump the break and it will break free. Not this time. So I figure, I have to manually separate the clutch with a crowbar, thank god for the inspection hole. I learned allot from you, thank you very much for your video.
I am glad you found my video helpful! The next time that you know you won't be using the tractor for a while, try wiring down the clutch pedal when you park it, may be able to avoid the problem this way.
Thanks for watching!
Hey Can you tell me what is size and thread on bolts what you are using to lock that clutch before pulling it off flywheel. we have mm bolts here as normal so i have to probably order those..
I am not certain what size they are, I just saved a set that came with a new clutch that I had installed. I think the y take a 10MM socket if that helps narrow it down. Thanks for watching!
Hi Dave, My mother inlaw has a Massey 35 the clutch works fine untill you engage the PTO then it sticks and you either have to try and pull it out of gear or shut it down to stop. Is it just stuck and it will come good with a bit of work or is it stuffed?Thank's
+Wayne Appleyard Is it just the PTO that sticks or the transmission?
Question: when I release my clutch, I get a chattering noise/knocking sound from the gear box, if I release it real slow sometime it does the noise and sometimes not, any ideas on this problem? Otherwise the clutch works fine, don't seem to be any hydrolic problem as I can tell. Thanks
You're going to have to dig into it to know, it could be anything from oil on the clutch to a bad bearing in the transmission. Thanks, for watching!
Great job. I had mine changed and it's squeaking like crazy and the pto clutch needs changing. Id love to put a bigger hydraulic pumpin
As far as I know there was only one pump, 4 gal/min, not very fast! Thanks for watching!
Thank sir for the clutch video awesome idea ply wood
The jack would sink into it as well, I now use a couple of flat steel bars I came up with to roll the jack on. Thanks for watching!
The alignment shaft you used, is it from a junk tractor or did you purchase it? Only tool i dont have
The shaft we use is from a junked tractor, some kits have the tool included or with some creativity you can jury-rig one.
Thanks for watching!
I paid a shop to replace the the two stage clutch in my MF3165 (basically a 165) I now only have about half the clutch pedal travel that I had originally. The PTO never disengages and when the pedal is pressed, I hear a loud rubbing sound that I can feel in the pedal. The Clutch, Pressure Plate and throw out bearing are supposed to be new but I believe I'm hearing a bad or incorrectly installed throw-out bearing. I left the machine at the shop but they already have my check. They are telling me "it probably only needs some adjustment" I'm afraid something was damaged in reassembly or perhaps the wrong part was installed. Your thoughts HELP!!!
If you have less pedal travel it would not be going far enough to disengage the PTO clutch, there are 2 holes for the linkage on the clutch pedal, it could be in the wrong hole. The noise and bad feel in the pedal is definitely something that needs sorted out though, a seized release bearing can wear right through the clutch levers.
Thanks for watching!
Hi Dave, its the transmission i'm assuming because it keeps driving along with foot on the clutch and wont stop but it only does it when the PTO is engaged other wise its fine. PS she uses the tractor a fair bit so it hasen't been sitting around.Thank's for your reply.
Cheers
+Wayne Appleyard Does the tractor have live PTO (2 stage clutch) or transmission driven PTO? If it is transmission driven and running something like a bush cutter, the momentum of the bush cutter will push the tractor even after pushing the clutch pedal. With a transmission driven PTO you need an "over running clutch" attachment for the PTO output shaft. Its a little extension shaft that goes on the output shaft of the tractor to let the implement free wheel when you shove the clutch.
+Wayne Appleyard That's good news, I glad I was able to help!
Hi Dave, I have an International 444 and the clutch pedal no longer depresses the clutch. I took the return spring off and the pedal just dropped down to rest on the foot board. I can move it up and down freely but it does nothing. The clutch works fine as I can start it in gear and the tractors moves fine. I can also take it out of gear and into nuetral by slowing the RPM but can only get it back in gear by killing the motor. I have not removed the plate yet to look up into that area. Seems like something has come loose. It has always worked fine. This happened all of a sudden. Any thoughts?
That sounds like either the clutch pedal shaft or the release bearing forks broke (likely the forks), pull the plate off the bottom of the clutch housing and you should be able to see. One other possibility is that the clutch pedal came loose on the shaft, but I wouldn't think it would happen that fast.'Thanks for watching!
I removed the plate and nothing was broken. The clutch pedal shaft had gradually, over time, slipped to where it no longer engaged the pressure plate when you push down on the clutch pedal. A fairly simple fix. I also made sure I had proper free travel. Thanks Dave. Like your videos.
I opened the same tractor but I have problem with pto when I press the clutch pedal pto doesn’t stop it has to be with the adjustments on pto disc?? Or something else
It could be a clutch pedal adjustment, pressure plate adjustment, or the PTO clutch disk stuck to the pressure plate. Thanks for watching!
I have a 135 diesel 1973 vineyard industrial model massey ferguson, 8 speed transmission .non multipower and it needs A 10" 10 spline pto disc for the clutch Yesterdays tractor doesn't carry where do you find one
If you check out A&IProducts.com you can find a locate a local dealer through their dealer locator or any local tractor dealer should be able to get one for you. Thanks, for watching!
good video Dave! looks like you will be doing a front axle pivot video next?
my question is on my 1955 TO35 without live power, this tractor was available with live bad an option... can I get live power by swapping in 2 stage clutch, or are there internal differences inside the case too? thanks Robert
Thanks, I'm glad you enjoyed the video. The entire transmission is different with live power, there is extra shafts and gears. Thanks for watching!
thank you sir!
hi thanks for the videos,I have a mf65 a4.192 none multi power.A ball from a bearing when through third gear and the bearing was replaced .Now third and reverse have a ticking noise . should the gears be replace or keep it working and wait till a transmission overhaul?
Hey Juan, I'm glad you are enjoying the videos, Thanks for watching!
It would be a good idea to take a look. It's probably chips off a couple of gears, but if its missing teeth it could lead to gears piling up and breaking the transmission case.
thanks for the reply . I'm planning on a tear down soon.I would love to see a video on trans overhaul procedures to make things easier for many people.
thanks from Mexico
Thanks for all your videos!
You're very welcome, I'm glad you enjoy them!
Hello, nice video you made about clutch replacement!! I did the same job on my mf 35. You told in the video that it was you're second clutch plate because off put pressure on the first one. I'm afraid i made the same mistake. Can you tell me what exactly happend
THe owner installed the first clutch and didn't get it all the way together before he tightened the bolts, the spline hadn't started on the transmission disk and bent the hub in the disk. When he found he had trouble he brought it to me.
Thanks for watching!
Is a 203 and a 236 engine has the same bolting up?
I believe that where they bolt to the transmission is the same, they likely had different rear engine plates though. Thanks for watching!
Very nice
Dave, How do you remove the input housing on an MF65, American built, ser # 673,543. It is dual clutch like this video. you use one as the alignment tool. I thought the 4 bolts on the housing and the pto shaft and housing just slipped out. HELP!
You will have to push the bottom shaft to the rear out of the bearing till it drops down so there is clearance for the input shaft to come out. Thanks for watching.
Heya, my MF165 is making a knocking noise. When I took the clutch cover off the bottom it sounds like it's coming from that area. The knock does go away when I rev the old perkins to 100rpm. I'm thinking I will take the oil pan off and inspect the bearing mains. Driving me nuts but the tractor runs great and has good oil pressure. I was told to unbolt the inspection plates on both sides of the transmission (two bolts in a diamond shape), but I'm not sure if those hold anything internally?
The two small diamond shaped plates are the retaining pins for the hydraulic pump, the inspection plates are the round ones about half way up the sides. One or both of the retaining pins for the hydraulic pump could be broken which could cause a knocking noise, you would be able to see that through the round covers on the side. You will want to at least partly drain the hydraulic oil or it will spill out when you take the covers off. Thanks for watching!
I looked at it last night, sitting in the seat on the left is the cover the one with the PTO-Engine RPM, PTO off, PTO hydraulic? Those covers, there is one on the other side as well. I also notice that the fluid is milky so I have water in there some how! Ordered new shift booties, maybe the that is the issue. Just want to inpsect the pump to make sure, though.
Those are the covers. Shift boots will go a long way toward keeping the water out. Good luck!
Awesome Video. Purchased a Mf175 a few months back, the guy had told me that he put the pto clutch in 180 Degrees off. Is that possible? When I try to engage the pto it starts to grab at the end of the pto lever movement. Please help!
I am glad you enjoyed the video. It is possible that he put the disk in wrong side toward the flywheel, that certainly could make it grab. Good luck and thanks for watching!
I have the Massey 165 and it is a hydraulic lemon. It has the Multi-Power that doesn't work and the hydraulic outs don't work either.
Liked your video tho.
That could be the auxiliary pump. Thanks for watching!
Thank you so much for this vid..about to do the same job (different make but same two stage principal) I can see more than what was said at 6:08 when I try this lol
I'm glad you found the video useful, that makes the effort worthwhile! Thanks for watching!
i am not familiar with MF but do you have to adjust pto clutch to 60 thou clearance before pushing back together .. did you renew release bearing??
New release bearing and pilot bearing,the new pressure plate should be pre-set, the clearance is .080-.090. Thanks for watching!
Our Massey 165 with the 4.203 Perkins blew up the other day
Thanks a lot a use full video.
I am glad you enjoyed the video, thanks for watching!
My Massey Ferguson 30 1974 clutch .
Has a 11" primary and 9 " secondary for PTO
I don't see that in yours ?
That would be the identical clutch to the one in this video, you don't see the 9" PTO disk because it is captive in the center of the pressure plate assembly but if you look close at the assembly you can see the spline hub of the disk.
Thanks for watching!
have MF 275 TRACTOR (PRIOR TO 9A349239), I have followed your instruction and changed the clutch, now I am trying to put the wire back and don't know how to get power to the glow plugs. I see Deisel fume of the exhaust but no fire because I do not know how to get power to the glow plugs. The MF 275 wiring diagram does not show where the wires get connected to.@t?
A 275 should have a manifold heater on the intake manifold, there will be a plug on the wire harness in that area to plug in.
Thanks for watching!
Can anyone help me pls? I have a Lenar FS 254 II tractor. It's done hardly any work and went through a flood.
Is been sitting for quite some time and the clutch doesnt seem to disengage at all. Is a two stage clutch. Could it be that it is rust stuck on the pressure plates and the transmission disks? It has three adjustment points and also three limiting bolts. I wonder after watching this if what I think is the limiting bolts should be undone a lot more. Can anyone point me to some instru tion on how to properly adjust this clutch? I would be grateful for any help. Regards to all.
Florian
Great Video! Thank You! Liked !! Subbed!!
I am glad you enjoyed the video, thanks for watching!
Is there singal clucth to changed dual clucth?
These tractors could have either single or dual clutch, but the flywheel and transmission are different between the 2. You can't change from dual to single or single to dual without changing flywheel and transmissions.
Thanks for watching!
I found this video very helpful thanks
I am glad you found the video useful, thanks for watching!
nice video I have a 1966 165 mf good tractor
I am glad you enjoyed the video, thanks for watching!
Hi Dave, I'm not sure, i'll go around this arvo and have a look, Thank's mate
Cheers
Is this also what's on the MF 240?
A 240 could have this 2 stage clutch or a single stage if it has hydraulic "independent" PTO. If you press your clutch all the way down to stop the PTO it's the 2 stage clutch. Thanks for watching!
thank you man good job
Thank you, I appreciate the compliment. Thanks for watching!
Will this be the same procedure on a 2007 MF 596?
Yes, it will be a very similar process. Thanks for watching!
loved the video...very useful!
Thank you, I'm glad you enjoyed the video, thanks for watching!
I need a little idea with my massy Ferguson when I press the clutch paddle the hydraulic just go down
When you press your clutch the hydraulic pump stops pumping. I expect that your lift cylinder is getting worn and scarred up so when the pump stops the oil bypasses and your lift drops.
Thanks for watching!
444 International diesel tractor head bolts please help
Singal cluch tractor me dual cluch set ho sakta hai kya
Sorry buddy, I don't understand, I only speak English. Thanks for watching!
is it the same with a massey ferguson 35 ???
As long as the 35 is a 2 stage clutch, yes the process is the same. Thanks for watching!
Massey Ferguson??
Yes, a 165 as I recall. Thanks for watching!
Un video explicativ cu schimbarea kit ambreiaj la tractor international harvester 444 te rog ?
I am sure I will make a clutch video for a 444 at some point but the process is much the same.
Thanks for watching!
Those boys will be vary smart some day just knowing how to split tractor means their smarter th en 99% of kids their age .
Thanks for watching!
Thank you sir
I am glad you enjoyed the video, thanks for watching!
SAME PROCESS FOR HINOMOTO E150D?
I have never heard of a Hinomoto tractor but if it has a 2 stage clutch is should be similar. Thanks for watching!
"1,202"
i have a ford 1900 does anyone have an exploaded view of the captive disc replacement
+Israel Hernandez You can find the parts book online at partstore.agriculture.newholland.com/us/ . There is no instruction on the how-to side but you can see how things fit together. Just type in your model number in the search box.
thank you that will me out in the future too that has just about everything i need to look at so i feel better about tearing into in the future
+Israel Hernandez You're welcome, glad I could help.
Hola ocupo piezas para el Zetor
If you do a google search for Zetor parts in your area you should be able to find a parts dealer. Thanks for watching!
You don't know what number part I have a Massey Ferguson 165
165 could have single or dual clutch, 11 or 12 inch and with a dual it could be a 10 or 21 spline PTO disk, you won't know until you take it apart. Thanks for watching!
Thanks 💞💞💞😘👍
I am glad you enjoyed the video, thanks for watching!
Voted down. Needed to see why my 2 stage wont come apart and you skipped across the disassembly
Hay
Ok
OK
L
I need a little idea on my Massey Ferguson when I press the clutch paddle the hydraulic go down