Totally amassing guys... I'm getting ready to do my 2008 G35X and this video was a great help.... I realized that a lot of pre planning went into this. very nice vid... thanks for sharing.
Right! It makes all the difference in the world, I replaced my clutch and flywheel on that exam same car with just a jack and jack stands... It was a nightmare. Thinking back I don't know how we did it.
Thanks for the great video. I'm about to do the same on my car. Did you have to drain the automatic transmission fluid before you separate it from the engine? Thank you.
I just had my engine changed (g37) with a q50 3.7 block i conected everything but the engine turns over but it wont start. Now that little ground wire that you were trying to unplug passenger side under the car that seems to go from the exhaust manifold to the body. I remember it on the g37 engine but it was not a plug it was bolted onto the body. Now this new engine did not come with that ground wire will this prevent the car from starting. I also dont have any codes. Any help appreciated. Thanks
I am doing an engine swap on my 2009 G37x and did not have a lift so I went in through the front. I have the old motor out but I can't get the new one in flush with the transmission and onto the mounting brakets because the exhuast manifold on the right hand side is in the way. Is there a way to get it in without breaking anything and get it flush with the transmission? The transmission is still in the car. We also disconnected the front differential and connected it to the engine to make it easier to get in. The center axle is also in the engine. We just can't get it in there and get it to line up. Any ideas? Any advice would be greatly appreciated.
@@danielthomas4018 Yeah I did it was a massive pain but we got it done. It took a lot of pry bars, transmission jacking, and curse words but eventually we got it in.
I have a question for a Project I am working on in my mind ... Can you install the 3.7 into a QX60? Yes, I am aware of the engine bay space, engine mounts, rear diff, axela, etc... What do you think?
Question I have a 2007 rwd g35 sedan I need a new engine I found a g37 coupe engine would it fit would no problem plug and play plz help I wanna get the engine ASAP from this guy
Lots of good information in here but holy does your lighting blow, camera is either out of focus or it's too dark to see 1/3 of the things you are trying to show off.
What’s the estimated cost to replace an engine on a g37? I want to get an idea so I don’t get overcharged! I’m already broke and I’ve found a q50 engine online that I really like because of low miles and warranty It’s fine for me to buy and it’ll fit right? Nothing is different?
What model HaulMaster lift table is that? Trying to get table specs to ensure I get a lift table that will hold the engine/trans like you did in the vid.
How can the vq35 ecu run a vq37 it would be lean from the mid range to the top of the rpm curve. Are the ecu's coded to the chassis number or can they be changed. Thank you
So I Did the swap already but the car doesn't want to turn over.we replaced with new starter, battery,n sparkplugs but the car doesn't turn over?..any ideals wut it can be? Would really appreciate it
Eugene. Is it possible to replace engine of 2011 G25 with VQ37 engine? Direct bolt on/start? Does it require replacement on transmission/ECU/wire harness etc... To be replaced as well? I guess it would be less headache if I just sell perfectly running G25 and get a good G37. 😁
This is unrelated, but would you happen to know what causes a certain noise in a lot of Infiniti Gs. At around 1-2k rpms, when slowly accelerating from a stop, doesn’t happen all the time, it sounds like ratting maybe coming from engine compartment or possibly from the undercarriage. My guess is that it could be a loose heatshield maybe? It doesn’t happen from just revving the engine while parked... and as mentioned before, it happens to a lot of Gs (37s/35s). I don’t believe mileage is of concern. My car happens to be a 2011 G37X Sedan with the 7AT
it's probably the catalytic converter(s). it's easy to check this. Remove the y-pipe and see if the material inside is moving/loose. An easy way to determine the catalyst noise is to listen to each cat when the noise is occurring.
@@EnthusiastAutoCare Yeah, that sounds definitely like what might be the cause. I'll get to it eventually. No dash lights or performance issues at the moment so i'll wait a bit before addressing the issue. Thank you for taking the time to reply to my comment.
If I was looking to modify it, I would. But this one is staying completely stock, due to being a daily driver. Don’t want to compromise reliability. 👍🏽❤️
@@rigoarteaga1038 I improve reliability with a tune over stock and I will get you better fuel economy. It's a win-win. I Can explain in detail if you reach out.
Great video... finally, someone whom can explain engine replacement clearly concise step by step methods. And with more adjectives...lol. Very professional...thanks again! I own a 2004 350zr, getting this exact noise from inside the passenger cabin side. I presume...way before this happened, I may have tightened up both Alt./AC belt a little too much...maybe this was a start of a problem. Watch this video, this the noise I hear! ruclips.net/video/r0xksoTvuME/видео.html Hope you receive my message, perhaps you can help me with it. Thank you very much in advance!
Awesome video. I have an 08 g37 coupe. I'm thinking of engine swapping a VR tt engine in my G37. Any thoughts? Or advice you can offer? Any information would be MUCH APPRECIATED
I would recommend replacing your engine and ecu with a newer version and installing a btw tuning GTR TT kit (btwtuning.com). Alternatively a topgunz "ACE" supercharger kit is also an excellent alternative. As for the fuel system I would recommend a radium surge tank setup, I've been very pleased with that kit or you can choose to do a traditional CJM return fuel system kit. I can provide you with a replacement ecu also, as the factory 2008 ecu does not have enough rom space to fully install all of ecutek racerom features. Feel free to contact me with any additional tuning questions.
Its the same for a 370 right? Not that i plan on pulling my engine anytime soon. Just curious if thats the only way to get it out? Can they come out of the front? Or this just the best, easiest way?
Nicely done. Being my first observation, it's easy to gather eugene is great at what he does. Is it possible to submit any questions for him? @enthusiast auto care
@@EnthusiastAutoCare Hey I have a 08 g35 sedan and I just bought a 2013 g37 sedan for parts and I wanted to no if its possible for me to swap motor and trans from the g37 to my g35
The vq37 will mount directly in places of a vq35. May need custom plumbing and will need the vq37 ecu. Even the vr30tt mounts directly in. Needs shorter engine mounts. Check NoirTm. Doin his vq30tt swap into 370z in driveway. Had engine stuffed in less than a day
@@samuelarizmendi the vq35 to vq37 swap is all over the z and g forums... Z1 did a vr30 swap also but they were no help to me, Noir, or others trying to figure this 1 out. Noir goes from start to finish in a simplified condensed version but is very responsive to YT and IG.
We got the motor in my 2009 intiniti g37x after a motor swap (same motor from different but exact same car) and the car refuses to do anything other than click the starter. The flywheel won't even crank. We have tested the battery and the starter and both are good. We need help. Why won't this thing start? Is there something we need to do with the ECU?
Bruh you need a lift because to replace engine on that you need to drop the entire front subframe, if you were in Pittsburgh I could have done it for you.
San Saechao pulling off the front end is much more time consuming. The factory recommended procedure is to drop the engine with the subframe as we do here in this video.
Time and money. Figure about 8 to 10 hours unhooking things and another 10+ hours putting things back in + the cost of getting the A/C unit charged, Power steering working, coolant refilled. I figure this is about a 4k job and that doesn't include the spare engine. Also you should ensure the spare engine was not abused and I would replace the dreaded galley oil gasket with the reinforced metal one. It's not a cheap job and if you could find a spare engine and work on it part time while you get your funds together, It may lesson the blow financially.
I need help and don't want to get ripped off by mechanic I'm throwing two codes p0300 and p0021 car runs in limp mode after 2k rpm engine and muffler sound like a tractor trailer and shaking i have a 2009 infiniti g37xs AWD sedan HELP PLEASE.
@@Trinibad718 Thats funny because my BMW has broken down more times on me than i can count...my infiniti? 0 times.You want to know what kind of taxis are used in Germany? BMW's lol because they are crap beater cars.
I have 2008 g35x AWD. I need to remove the engine. I need help with that engine can’t move freely I can get torq bolt out. What is the best way for me to make drop engine transmission and transfer case at same time or
Totally amassing guys... I'm getting ready to do my 2008 G35X and this video was a great help.... I realized that a lot of pre planning went into this. very nice vid... thanks for sharing.
How did it go? I have one Im debating on swapping engine myself.
You can tell this man got his shit together, kano kroil way better than PB blaster and Amsoil oils!
liquid wrench is the best .check out project farm.
I would like to know if they live in Miami to do that job of a 3.7 infiniti engine for a 350z chassis?
Great video! I remember watching this video a while back, glad its still up! Thanks
AYE BRO!!! Ive seen all your vids on your Hr the past months and finally got an Hr lol what were your first bolt ons when you got your Hr?
Alex Villalobos yeah bro bolt on 350z hr, 310whp back in 2012 going hard!
Cool video. I'm assuming that coming from the top will present it's own challenges.
ماشاء الله...very nice and properly job....thinks from Algeria
Nizar Bakir thank you!
Makes it look so easy , if only I had a lift and bigger garage.
Right! It makes all the difference in the world, I replaced my clutch and flywheel on that exam same car with just a jack and jack stands... It was a nightmare. Thinking back I don't know how we did it.
Nice shop! Very clean.
What should u change on the new (used) engine before the swap also did they ecu receive any issues
Wow...amazing content..Thank You!
Hr and vhr all the wire connect are the same ?
Love all the new content!
Thanks for the great video. I'm about to do the same on my car. Did you have to drain the automatic transmission fluid before you separate it from the engine? Thank you.
yes, but it's not required.
I just had my engine changed (g37) with a q50 3.7 block i conected everything but the engine turns over but it wont start. Now that little ground wire that you were trying to unplug passenger side under the car that seems to go from the exhaust manifold to the body. I remember it on the g37 engine but it was not a plug it was bolted onto the body. Now this new engine did not come with that ground wire will this prevent the car from starting. I also dont have any codes. Any help appreciated. Thanks
Run the new q50 computer well your at it lol
I am doing an engine swap on my 2009 G37x and did not have a lift so I went in through the front. I have the old motor out but I can't get the new one in flush with the transmission and onto the mounting brakets because the exhuast manifold on the right hand side is in the way. Is there a way to get it in without breaking anything and get it flush with the transmission? The transmission is still in the car. We also disconnected the front differential and connected it to the engine to make it easier to get in. The center axle is also in the engine. We just can't get it in there and get it to line up. Any ideas? Any advice would be greatly appreciated.
Did you figure out to get it lined up?
@@danielthomas4018 Yeah I did it was a massive pain but we got it done. It took a lot of pry bars, transmission jacking, and curse words but eventually we got it in.
Hello , does anyone know if a 2013-2015 q50 3.7 will fit in my 2010 G37 7AT ?? Please any info helps a lot
Awesome work! How much did a job like the cost to overhaul? I have a g37 sedan, and I want to put a new used engine in it so I can boost it.
I have a guy he charges 1000$
@@Trinibad718 where are you located I need this done
@@Trinibad718 😂
@@Hayer0228 😂
I have a question for a Project I am working on in my mind ... Can you install the 3.7 into a QX60?
Yes, I am aware of the engine bay space, engine mounts, rear diff, axela, etc...
What do you think?
what is needed for 2008 g35 to swap in a 3.7 engine? direct bolt on? computer and harness?
I bought a 2010 g37x awd and wanna install in a G35xS
Bro please make a vid
I’m getting ready to do this job myself. Is a 1000 lp capacity lift table enough for that motor and trans ?
Question I have a 2007 rwd g35 sedan I need a new engine I found a g37 coupe engine would it fit would no problem plug and play plz help I wanna get the engine ASAP from this guy
Did you get a answer yet?
@@nrrzkv yea I did lol engine had a different set up unfortunately I had to get 07 08 g35 sedan engine so it can be a exact fit…
do you have to adjust timing when replacing the motor ? or just installing and start it
Just install
So what engine can make the most power with mods ?
What year chrome engine would a 2012 work in the swap ?
Do you have to remove the transmission to take out the engine ?
Can you replace the engine with Red Sport 400 ?
Hey man, I was wondering if you could show me or point me towards where I could get a reliable 3.7 engine
1.) LKQ (6 mo warranty)
2.) SWEngine (5 yr warranty)
3.) EBAY (they come with buyers protection if your sold a POS)
Lots of good information in here but holy does your lighting blow, camera is either out of focus or it's too dark to see 1/3 of the things you are trying to show off.
Awesome video Eugene! How many hours did it take you, or how many hours does it take you to do a swap like this?
15 hours if you know what ur doing
@@mohamedmohamedali177 hi, Can y'all swap My 2008 G35x AWD to a G37X AWD
@@hollygrovedallashg8709 I don’t work with these guys I just saw the video and commented
Where are you guys located im going to be overhauling my q50 and probably replacing the engine. By the way your shop is immaculate.
We are located in Concord, California.
what are you replacing your engine for? I need to replace my g37 engine waiting to purchase one soon
What’s the estimated cost to replace an engine on a g37? I want to get an idea so I don’t get overcharged! I’m already broke and I’ve found a q50 engine online that I really like because of low miles and warranty
It’s fine for me to buy and it’ll fit right? Nothing is different?
What model HaulMaster lift table is that? Trying to get table specs to ensure I get a lift table that will hold the engine/trans like you did in the vid.
This is the largest model that is offered by harbor freight.
The Haul Master lift table rated 1000 lbs. I highly doubt that the 500 lbs will support the power train regardless of the vehicle.
Can you swap a QX70 engine with a Q60s red ?
How can the vq35 ecu run a vq37 it would be lean from the mid range to the top of the rpm curve. Are the ecu's coded to the chassis number or can they be changed. Thank you
please call me for tuning and to discuss this. 415-830-4008
So I Did the swap already but the car doesn't want to turn over.we replaced with new starter, battery,n sparkplugs but the car doesn't turn over?..any ideals wut it can be? Would really appreciate it
Check to make sure the engine can rotate freely by turning the crankshaft manually.
Did this make the Demon Bolts on the Cats / Headers easier to take out?
Angelo Daniel Negron yes but they still broke :)
Eugene. Is it possible to replace engine of 2011 G25 with VQ37 engine? Direct bolt on/start? Does it require replacement on transmission/ECU/wire harness etc... To be replaced as well? I guess it would be less headache if I just sell perfectly running G25 and get a good G37. 😁
I haven't tried that..
A Pro @ Work My friend.
This is unrelated, but would you happen to know what causes a certain noise in a lot of Infiniti Gs. At around 1-2k rpms, when slowly accelerating from a stop, doesn’t happen all the time, it sounds like ratting maybe coming from engine compartment or possibly from the undercarriage. My guess is that it could be a loose heatshield maybe? It doesn’t happen from just revving the engine while parked... and as mentioned before, it happens to a lot of Gs (37s/35s). I don’t believe mileage is of concern. My car happens to be a 2011 G37X Sedan with the 7AT
it's probably the catalytic converter(s). it's easy to check this. Remove the y-pipe and see if the material inside is moving/loose. An easy way to determine the catalyst noise is to listen to each cat when the noise is occurring.
@@EnthusiastAutoCare Yeah, that sounds definitely like what might be the cause. I'll get to it eventually. No dash lights or performance issues at the moment so i'll wait a bit before addressing the issue. Thank you for taking the time to reply to my comment.
Rigo Arteaga hit me up for a tune !
If I was looking to modify it, I would. But this one is staying completely stock, due to being a daily driver. Don’t want to compromise reliability. 👍🏽❤️
@@rigoarteaga1038 I improve reliability with a tune over stock and I will get you better fuel economy. It's a win-win. I Can explain in detail if you reach out.
Thank you so much
what song/tunes playing?...fire!!
Great video... finally, someone whom can explain engine replacement clearly concise step by step methods. And with more adjectives...lol. Very professional...thanks again! I own a 2004 350zr, getting this exact noise from inside the passenger cabin side. I presume...way before this happened, I may have tightened up both Alt./AC belt a little too much...maybe this was a start of a problem. Watch this video, this the noise I hear! ruclips.net/video/r0xksoTvuME/видео.html Hope you receive my message, perhaps you can help me with it. Thank you very much in advance!
Awesome video. I have an 08 g37 coupe. I'm thinking of engine swapping a VR tt engine in my G37. Any thoughts? Or advice you can offer? Any information would be MUCH APPRECIATED
I would recommend replacing your engine and ecu with a newer version and installing a btw tuning GTR TT kit (btwtuning.com). Alternatively a topgunz "ACE" supercharger kit is also an excellent alternative. As for the fuel system I would recommend a radium surge tank setup, I've been very pleased with that kit or you can choose to do a traditional CJM return fuel system kit. I can provide you with a replacement ecu also, as the factory 2008 ecu does not have enough rom space to fully install all of ecutek racerom features. Feel free to contact me with any additional tuning questions.
Enthusiast Auto Care
Ok. Good advece. Thanks for reponding I'll keep that in mind. If I have any more questions I'll ask. Thank you!!!
how many hours is that job?
Its the same for a 370 right? Not that i plan on pulling my engine anytime soon. Just curious if thats the only way to get it out? Can they come out of the front? Or this just the best, easiest way?
Yes this is the same for a 370z. They can also come out from the from but it's a lot more work.
What's book time on R&R??
Nicely done. Being my first observation, it's easy to gather eugene is great at what he does. Is it possible to submit any questions for him? @enthusiast auto care
Citizen Hoyle 101 thanks! You can reach out any time call me on my shop line if you want to chat.
Did you use the stock g35 Ecu or did you have to swap ecu too?
stock ecu. If you need a replacement ecu, send me a message.
@@EnthusiastAutoCare Hey I have a 08 g35 sedan and I just bought a 2013 g37 sedan for parts and I wanted to no if its possible for me to swap motor and trans from the g37 to my g35
Very nice vid.....!
I didn't think suspension components were necessary to take off in an engine swap? I just am lazy and hate dealing with lower control arms and stuff.
I just swaped my motor in my 37x now it won't recognize the key fob . Key has been reprogrammed and unlocks doors and opens trunk .
Sounds like something is unhooked or got damaged
Doing this Now
I have a g35x 2008 3.5 engine can i put a Q50 VQ engine?
It would be too complex, I don't recommend it.
The vq37 will mount directly in places of a vq35. May need custom plumbing and will need the vq37 ecu. Even the vr30tt mounts directly in. Needs shorter engine mounts. Check NoirTm. Doin his vq30tt swap into 370z in driveway. Had engine stuffed in less than a day
@@mikeschaner5853 were can I see or get this info I have an 08 G35x and I want to do either or swap for a vq37 or the 3.0tt
@@samuelarizmendi NoirTM on YT or @NoirTM on IG... Tell him i sent you over...
ruclips.net/video/yA7zVYuf_lI/видео.html
@@samuelarizmendi the vq35 to vq37 swap is all over the z and g forums... Z1 did a vr30 swap also but they were no help to me, Noir, or others trying to figure this 1 out. Noir goes from start to finish in a simplified condensed version but is very responsive to YT and IG.
Hello friend.. I have a question
Yes, what is your question?
eugene!!!! the master of vq shit lmfao
What does a job like this cost?
Will I be able to swap my 04g35 sedan auto to a manualvq37hr ?????
I also need answers
We got the motor in my 2009 intiniti g37x after a motor swap (same motor from different but exact same car) and the car refuses to do anything other than click the starter. The flywheel won't even crank. We have tested the battery and the starter and both are good. We need help. Why won't this thing start? Is there something we need to do with the ECU?
Alien Bros did you figure out the issue. I have the same problem
Any suggestions, I'm in Philadelphia and I need to swap out the engine in my G37X .. I need help!!! Anyone who reads this please and thank you
Bruh you need a lift because to replace engine on that you need to drop the entire front subframe, if you were in Pittsburgh I could have done it for you.
I'm in upper bucks hmu
@@audinthusiast3750 you can drop the driveshaft and disconnect the trans and you can pull it from the front
daniel powell that is just unnecessary amount of work
@@audinthusiast3750 yup but if you don't have access to a lift then you really don't have a choice unless you want to pay a shop.
Why didn't you pull the front end off?
San Saechao pulling off the front end is much more time consuming. The factory recommended procedure is to drop the engine with the subframe as we do here in this video.
@@EnthusiastAutoCare oh...well I'm pulling the front end off as we speak lol
@@sansaechao2023 lol how did it go? The front end procedure
Whats the cost of such a service?
The labor time is approximately 19 hours. The cost would depends on the shop's labor rate per hour. Gaskets/fluids are extra.
how much did this cost? this looks expensive as hell
Time and money. Figure about 8 to 10 hours unhooking things and another 10+ hours putting things back in + the cost of getting the A/C unit charged, Power steering working, coolant refilled. I figure this is about a 4k job and that doesn't include the spare engine. Also you should ensure the spare engine was not abused and I would replace the dreaded galley oil gasket with the reinforced metal one. It's not a cheap job and if you could find a spare engine and work on it part time while you get your funds together, It may lesson the blow financially.
Aprox how many hours?
too many.
It took me over 20 hours to swap a 350z motor lol
I'm it's a skyline only to the badge is infinity buddy 😂
Hey will a 350z engine fit in m35
yes, depending on the year and model, but generally speaking yes.
what was wrong with the engine?
The original engine was neglected, had sludge and had failed somehow as a result - I don't remember the details.
It's just a matter of time.
Anyone know on 4:40 what brown plug is for?
I have my wires messed up there, HELP!
If im not mistaken that's the connector for the power steering assist motor that's on the power steering rack
It's for the steering angle sensor to the rack & pinion
Qhzts wrongcwith the vq35
I need help and don't want to get ripped off by mechanic I'm throwing two codes p0300 and p0021 car runs in limp mode after 2k rpm engine and muffler sound like a tractor trailer and shaking i have a 2009 infiniti g37xs AWD sedan HELP PLEASE.
Blixky you should test the oil pressure. It is likely the rear timing cover gasket has blown.
@@EnthusiastAutoCare what's the readying o should get at idle and at 2500 rpm after the car warms up
@@Trinibad718 I dont understand your reply.
@@deathdealerhype7819 forget it infiniti sucks got a bmw and I'm in love
@@Trinibad718 Thats funny because my BMW has broken down more times on me than i can count...my infiniti? 0 times.You want to know what kind of taxis are used in Germany? BMW's lol because they are crap beater cars.
Hey I have a 08 g35 sedan and I bought a 2013 g37 sedan parts car and I want to swap motor and trans to my g35 do I have to change the ecu also.
Hey did you ever do this
I have 2008 g35x AWD. I need to remove the engine. I need help with that engine can’t move freely I can get torq bolt out. What is the best way for me to make drop engine transmission and transfer case at same time or
Yes