Thank you, I dissembled them and forgot how to put back the silver spring . Your video was the only one that helped me. I wish they taught stylist how to do this in beauty school.
You are welcome and thank you for watching. Yes I plan on being able to teach stylist schools and dog grooming schools how to take care of their equipment. Hopefully in the near future
This video was hella helpful. The plastic blade guide flew out of my trimmers (while I was at work 😭) and I tried watching other videos to help me 😂😂 but yours was the best!
These are my favorite liners of all time. I bought 4 of them and every single one cut amazing right out the box. I was able to get sharp lines on kids and adults without scratching them. Only problem is that the housing is very cheaply made. Every single one broke by where the blades go. When I got down to the last one, i treated it with extreme care, laying it down softly taking them out lightly and they still broke.
+classic1984 I do not know the sizes sorry. I order thru a Clipper distributor. I have an account to buy them and have to order over $100 minimum. Your can google im sure there is of part sellers.
Hello . Thank you for watching. If the cutter blade is moving then you will need to buy a guide for the blade if they are available or buy a new blade. If the whole blade is moving around on the trimmer then you will need to open to see why the metal inserts are moving and may need a bottom housing to fix it. Hope i helped
greetings great video! i was wondering, any advice of where i could buy 3 scews because i ACCIDENTLY dropped my Tpro and well i dont know how but the screws just came off now i need three of them! PLEASE REPLY!!!!
Mines became very loud for some unknown reason while I was about to line my hair. They're almost brand new, only used them a few times and never dropped them. They were quite and smooth, now they're not. Any ideas on whats causing this?
+romedc Well hard to diagnose in a message. Check and make sure there's tension on the blade. If there is not it is the bottom case. It can be the blade guide is melted. It can also be the blade needing a sharpening and re-polish its surface. It also can just need oil on the blade. If all that is good then it will be a shot bearing in the motor and will need to be replaced with a new motor. If there not very old send back to Wahl for warranty. Well.Well good luck and have a nice day.
as I was opening and removing the motor the red and black wires came off...is there any diagram to show where it should be soldered any help appreciated the one ine the video is not the same {switch} as I am in uk
+Cloud's Diamond Sharpening it's not that old at all ..about 6 months old . At first the switch started acting up and getting stiff and then it wouldn't power on at all.
Anthony Garcia Since it sounds like the physical switch. If you replace the pcb/switch board it will work but if the fuse is blown out you will have to replace the motor also to prevent a new switch shorting out. I am not responsible if I am wrong. I can fix it if you can't. Good luck.
+Cloud's Diamond Sharpening Yea I'm pretty sure its the switch board because the switch won't budge either stays on one side. Could you email me @ anthonyg3295@yahoo.com because i need them fixed asap
+Anthony Garcia www.diamondedge2015.com for all the details. My dad past away and i have a memorial so to be honest i can't promise 24 hour turnaround. But i can fix it for sure. Maybe same day or maybe not.
F Ahmed I have no idea what screw your talking about but find a Wahl distributor and tell them the model number and what screw you need. Thanks for watching
Cloud's Diamond Sharpening hi its the blade screw from the underneath used to adjust how aligned the blade is, i have looked everywhere but cant find the screw size or the part
hi, ok . Its the same screw on a andis outliner blade screw. I dont sell parts. I just fix them. Google search for a wahl distributor. Or you can try fort worth shaver and appliance.
Does anyone know the color bands on the Inductor? I think they are brown, green, brown. I'm trying to fix it. But if it doesn't work out I guess I can order a new PC Board. Thank!
+Christopher Diaz Well usually that problem happens from not oiling your blade and the motor has to work harder. It over heats. You will need to replace pcb with the motor. Have you ever got the blade sharpened? If not it will need to be done.
One of my inserts is loose and I just got them about 3 months ago and I take good care of them, never dropped them or anything bad can you help me please?
I took them apart and yea ur right but I swear I didn't tighten them to hard what I realized is that the detailers case is cheaply made. They are made to wear out within a couple months. Bad investment when they have so many better clippers.
northweezie1 hello. The blade inserts are turning inside the case. So you will have to take off the top of the case and use needle nose plyers to hold the nut from turning and then you will need to replace the housing.
me acaba de pasar lo mismo se me a caído la maquina y se a roto la carcasa de la parte inferior. si hay alguna persona que me pudiera decir en donde puedo encontrar una nueva carcasa inferior de la wahl de la misma marca de la que se ve en el video; se lo agradecería mucho si alguien me enviara la dirección de la pagina donde pueda conseguir
You cant make them more powerful unless you mess with the voltage. You can have them cleaned and sharpened. It will make them like new if nothing is broken on them.
Cloud's Diamond Sharpening Hi dont have this trouble with anyone else. its just ur back ground music is a little high over ur voice. i like you video. was just hard to here at times. thanks
np. Sorry for your troubles. you might try my other video of this trimmer. This video is almost 2 years old and i was new to making video's. ruclips.net/video/W-wkeEbm4Mk/видео.html
![[1299] Unpickable Locks From Stuff Made Here](http://i.ytimg.com/vi/Ecy1FBdCRbQ/mqdefault.jpg)
![[1299] Unpickable Locks From Stuff Made Here](/img/tr.png)
Thank you, I dissembled them and forgot how to put back the silver spring . Your video was the only one that helped me. I wish they taught stylist how to do this in beauty school.
You are welcome and thank you for watching. Yes I plan on being able to teach stylist schools and dog grooming schools how to take care of their equipment. Hopefully in the near future
This video was hella helpful. The plastic blade guide flew out of my trimmers (while I was at work 😭) and I tried watching other videos to help me 😂😂 but yours was the best!
Maruida Meower np, awesome I'm glad it helped you. Thank you for watching.
TY for this video, when adjusting the blades, that white piece popped out and I couldn't figure out how put it back until this vid.
No problem. Im glad i can help you and thank you for watching.
Magnificent video ,well explained by a teacher in how to repair this little trimmer.. thank you.
Thank you for watching the video and commenting. We appreciate the feedback.
Thank bro! Just saved me money buying a new set! 🤙
Thanks for watching.
These are my favorite liners of all time. I bought 4 of them and every single one cut amazing right out the box. I was able to get sharp lines on kids and adults without scratching them. Only problem is that the housing is very cheaply made. Every single one broke by where the blades go. When I got down to the last one, i treated it with extreme care, laying it down softly taking them out lightly and they still broke.
YouAwakeYet ya they are fragile but are very good getting the job done.
Thnx u this is the only one i found that helped and easy and made since, thnx
Np. Glad I could help and thank you for watching
Thanks for helping me out!
You're welcome!
Good video was going to bin mine as the spring came out but back up and running
Satbox Man np. I'm glad it helped you. Thanks for watching.
Thank you so much, you helped me reassemble it after accidentally disassembling it too far😂😂
Np. Im glad I helped you. Thanks for watching.
Me to! Great video, cheers dude!
Thank you so much this really helped me
Thanks for watching!
Bro good looking with this video 👍🏼 helped a lot
Thanks God for this video, save my day 😎👍🏾
, awesome no problem and thank you for watching
Great work brother
thanks for your help
thank you and no problem . Thanks for watch
Great work brother
+Tomekina Ofa Thanks for watching.
Awesome video man. I had the same problem with my whals and your video really helped.
Thank you and np im glad it helped you out. Thanks for watching
Thanks for the video 🙌
BoyTo2Nice np. Thanks for watching
great video
Larry The Barber Man thank you and thanks for watching.
Just what I needed. Thanks.
+Ryan Mascaro No problem. Glad i can help. Sorry about the loud music.
OMG thnx dude, u saved my Life.
I plugged a us trimmer into a uk 230V socket and it blew. Do you know what parts would need replacing and where i could get them?
I would encourage you to just buy a new clipper.
Very helpful thank you
No problem. Thanks for watching.
boy you just saved my life lol, good look yung yung
Awe man... I should have watched this video BEFORE throwing mine away. Oh well. Good video dude.
+Royalty-Free Beats by Remi QX thanks for watching.
Where can i get one of those cases? The little tab the tension spring rest on, broke in mine..
Idada Edwards a Wahl distributor will have them.
Thanks nice video
This was helpful. What size/type are the 2 tiny screws that go into the 'under blade'? Mine have worn out the threads. Thanks
+classic1984 I do not know the sizes sorry. I order thru a Clipper distributor. I have an account to buy them and have to order over $100 minimum. Your can google im sure there is of part sellers.
where I get the plastic nice video 😃👍💈
At a Wahl distributor. Thanks.
yea
great video.. but how to solve the problem with the blade moving and the screws are tight as can be?
Hello . Thank you for watching. If the cutter blade is moving then you will need to buy a guide for the blade if they are available or buy a new blade. If the whole blade is moving around on the trimmer then you will need to open to see why the metal inserts are moving and may need a bottom housing to fix it. Hope i helped
greetings great video! i was wondering, any advice of where i could buy 3 scews because i ACCIDENTLY dropped my Tpro and well i dont know how but the screws just came off now i need three of them! PLEASE REPLY!!!!
Jesús Maldonado hello and thanks . you will have to search in google for a Wahl distributor.
Mines became very loud for some unknown reason while I was about to line my hair. They're almost brand new, only used them a few times and never dropped them. They were quite and smooth, now they're not. Any ideas on whats causing this?
+romedc Well hard to diagnose in a message. Check and make sure there's tension on the blade. If there is not it is the bottom case. It can be the blade guide is melted. It can also be the blade needing a sharpening and re-polish its surface. It also can just need oil on the blade. If all that is good then it will be a shot bearing in the motor and will need to be replaced with a new motor. If there not very old send back to Wahl for warranty. Well.Well good luck and have a nice day.
appreciate it man thanks
No problem
How often do you sharpen your blade?
Ronald Cheatham it depends on who sharpens it and if you use oil and how many times you use it.
Hi thnx for reply i put those back together now they are loud and not cutting dk what i did wrong ugh!!!!
Please I need the setting cover mine is bad. You have really help me that great job. How can i order it please help me.
Roland Tata hello. Np. Do a Google search for Wahl distributors and find the company you want to buy it from. Thanks for watching.
as I was opening and removing the motor the red and black wires came off...is there any diagram to show where it should be soldered any help appreciated the one ine the video is not the same {switch} as I am in uk
Hi Freind i need that plastic replacement full set
Hello. You'll have to find a Wahl distributor
If the fuse blows out where can i get another fuse?
Im not sure if they're available any longer.
My Detailers won't turn on for some reason. Switch seems to be broken and wont power the trimmers. What do you think it could be?
+Anthony Garcia Hmm. I don't know. How did it break? Did the physical switch break? Did the pcb blow a fuse? Do you oil your blades? How old is it?
+Cloud's Diamond Sharpening it's not that old at all ..about 6 months old . At first the switch started acting up and getting stiff and then it wouldn't power on at all.
Anthony Garcia Since it sounds like the physical switch. If you replace the pcb/switch board it will work but if the fuse is blown out you will have to replace the motor also to prevent a new switch shorting out. I am not responsible if I am wrong. I can fix it if you can't. Good luck.
+Cloud's Diamond Sharpening Yea I'm pretty sure its the switch board because the switch won't budge either stays on one side. Could you email me @ anthonyg3295@yahoo.com because i need them fixed asap
+Anthony Garcia www.diamondedge2015.com for all the details. My dad past away and i have a memorial so to be honest i can't promise 24 hour turnaround. But i can fix it for sure. Maybe same day or maybe not.
Please where do i buy the in set case ?
Vikk U most Wahl distributor will have them. Or you can try fort Worth shaver and appliance or pet edge or Robbie's vet supply
where can I find the casing or housing? I am having trouble finding it . Thanks
+Emilio Almenas I answered your email. Thanks for watching.
HEY. Friend.
Hello
I lost the screw from the shaver head inside part what size is it
F Ahmed I have no idea what screw your talking about but find a Wahl distributor and tell them the model number and what screw you need. Thanks for watching
Cloud's Diamond Sharpening hi its the blade screw from the underneath used to adjust how aligned the blade is, i have looked everywhere but cant find the screw size or the part
hi, ok . Its the same screw on a andis outliner blade screw. I dont sell parts. I just fix them. Google search for a wahl distributor. Or you can try fort worth shaver and appliance.
Does anyone know the color bands on the Inductor? I think they are brown, green, brown. I'm trying to fix it. But if it doesn't work out I guess I can order a new PC Board. Thank!
hey how much u charge cuz my Wahl detailer burnt out I was wondering how much it was so you could put a new motor for me
+Christopher Diaz Well usually that problem happens from not oiling your blade and the motor has to work harder. It over heats. You will need to replace pcb with the motor. Have you ever got the blade sharpened? If not it will need to be done.
Why do I feel like playing Zelda after watching this video.
divined21 hah
Truth lol
One of my inserts is loose and I just got them about 3 months ago and I take good care of them, never dropped them or anything bad can you help me please?
Amin Sturges Hello, you over tightened the blade screws and it broke the inside of the case that holds the inserts from moving
I took them apart and yea ur right but I swear I didn't tighten them to hard what I realized is that the detailers case is cheaply made. They are made to wear out within a couple months. Bad investment when they have so many better clippers.
Thank you btw
Amin Sturges np and thank you for watching
Where can I get that replacement cover. I almost threw it away.
you have to find a Wahl distributor.
I am from India where can I get that replacement cover. Plz send some contact r link plz .that detalier brought fro USA
What website can I buy the Bottom case from
Simon Ramirez Google search , Wahl distributor. There are a lot of them.
my tension spring will not curve in when i put the cam follower on its pointing straight up and it dosent slant foward
Hello. If the tension spring is not keeping its tension it's because it is broken from the housing you will need to replace the bottom housing
Where did you get that grey back piece from
Jacob Nunez I do not no it was the customers. they bought it and sent to me. try a Wahl distributor.
Hey Bud where can I purchase that burgundy back cover, where did you buy your replacement parts? any help will do, thanks!!
Juan Gonzalez you will need to search online for a Wahl distributor. Sorry I don't sell parts. I just fix them.
how to put spring back in wahl color pro the black spring popped out and cant get it back in right
if it doesnt go back in easily the bottom case is probably broke or about to break
Pls the buttom part you about change where can I get it
Laotus ola hello. Google search Wahl distributor near you.
My blade doesn't come off no matter how hard I pull what do I do?
northweezie1 hello. The blade inserts are turning inside the case. So you will have to take off the top of the case and use needle nose plyers to hold the nut from turning and then you will need to replace the housing.
Hi bro, where can I get spare case for my Wahl hero please?
Hi. You can not get them. After the warranty is out it can not be repaired. No parts available. If it is in warranty, they will replace it.
Thanks
Sobitan Oluwatobi Wahl hero's have no parts available. sorry all you can do is buy a new one.
my detailers make a popping sound in the motor or blade when turned on, I do keep them oiled.
+33craigcarter It will either be a motor or a cam drive.(the piece that moves the blades). Good luck.
How do I contact you I need mines fixed
Www.diamondedge2015.com
Bro at 4:15 on the video my lil thing's feel off into the trimmer & weren't catching the screws any help?
me acaba de pasar lo mismo se me a caído la maquina y se a roto la carcasa de la parte inferior. si hay alguna persona que me pudiera decir en donde puedo encontrar una nueva carcasa inferior de la wahl de la misma marca de la que se ve en el video; se lo agradecería mucho si alguien me enviara la dirección de la pagina donde pueda conseguir
do you have motors for sale?
+Barber Toolz Nah sorry
Do you recommend the detailer or the andis t outliner?
how.can i make those more powerfull
You cant make them more powerful unless you mess with the voltage. You can have them cleaned and sharpened. It will make them like new if nothing is broken on them.
how can i contact you ??
the motor for the wahl detailer
+Barber Toolz I do not sell parts. Try google.
Music was a nice touch :/
Thanks for watching
Sick video but cant stand the music hahah
+CycloneProofProd. C2P Well sorry about that. Its free music and wont get me blocked. Thanks
+Cloud's Diamond Sharpening Your still the man though!!
anybody in the comments. The power (red wire) on the rotor motor detached from the mother board. (green board) how do I reconnect?
Solder gun and solder it back on by heating up the liquid metal
@@cloudsdiamondsharpening3973 link to a good (but affordable) solder gun?
anyone with a temperature gauge so you dont melt the pcb
where can i contact
www.diamondedge2015.com
I thought once it broke it was done
+Tomekina Ofa Nope not done, you can actually get every part on the clipper.
where can I order or buy that piece at mine broke for some reason.
What's up with the Conan the barbarian music.
BigSerg80 it's free music and I have a lot of videos.
lower your music. hard to here you
Jak Coleman buy treble speaker. thanks for watching
Cloud's Diamond Sharpening Hi dont have this trouble with anyone else. its just ur back ground music is a little high over ur voice. i like you video. was just hard to here at times. thanks
np. Sorry for your troubles. you might try my other video of this trimmer. This video is almost 2 years old and i was new to making video's. ruclips.net/video/W-wkeEbm4Mk/видео.html
Cloud's Diamond Sharpening oh right lol. i didnt realize. thank you. i will do that.