Great video! Do you think it can with stand the power of 45acp and 10mm? Would like to get one but afraid that mount will come out in time since the added weight that the beavertail needs
Thanks@@reddotsight1013 for the reply. I have the same mount with a Vector Optic Frenzy SCRD-1911 1x17x24 that I have been wanting to install for sometime now but hesitant to do it coz it might loosen up after extensive use. I am using a Roni Kit for my Glock in the meantime. I might go ahead and install it after seeing your video.
It is normal for the adapter to lift; it does not make contact with the front of the pistol slide. When you screw in the two small screws, the adapter must be parallel to the pistol slide.
New from Vector Optics is an adapter for Glock 17 MOS, which is very well made. It is only compatible with Frenzy-S red dot sights (Footprint MAG / RMSc). red-dot-sight.eu/products/adaptateur-compatible-glock-mos-empreinte-mag-rmsc-pour-frenzy-s
Has it in any way cause any damage to the back side of slide? From the pressure or every round going off I'd assume there might be some type of contact?
Asegúrate de que el visor de punto rojo esté bien fijado al arma. Repositiona los tornillos en el punto medio de su recorrido para empezar los ajustes desde cero. Dispara 3 cartuchos, luego ajusta 1 graduación. Repite este proceso: dispara 3 cartuchos, ajusta, y así sucesivamente hasta obtener el resultado deseado. Si no logras calibrar el visor correctamente, te recomendaría llevarlo a un armero, quien podrá ajustarlo en aproximadamente 10 minutos. Buena suerte.
@@steveboone7390 It doesn't work with the blowback softair but it depends on the brand of your replica. You have to check if your BB is compatible with Glock sights
@@2sirb2383 it's not the softair but the co2 version that is by Umarex that shoots 4.5mm bbs and not 6mm bbs, so is a faithful replica of the realsteel version.
@@reddotsight1013 but then is it still possible to remove the sight from the gun after the screws are glued? Also, how to change the battery in this case? (sorry i have not much idea about this red dot sight)
@@victorlcl With blue glue (Loctite 243/242) you can still unscrew the screws, but if you use red glue (Loctite 270/271) it will not be possible to unscrew the screws. For your information, the CR2032 battery has an operating life of 2 to 3 years.
The adapter used is exclusively compatible with non-MOS Glock models that have a slide width of 25.5 mm (1.0 inch). Your Glock 20 Gen4 has a slide width of 28.5 mm (1.12 inches). Therefore, this adapter is not suitable for your model of Glock. Regards, Raphael from RedDotSight.
the threads on my mounting kit for g17 stripped the first time i tried to screw it down today. i was using the same torque screwdriver in the video and i didnt even get close to 10 in.lbs. does this come under warranty because its a pretty serious quality flaw...
Ao apertar os parafusos da placa,a chapinha que vai no lugar da alça de mira se levanta um pouco,ficando achatada entre a placa de cima e o slide,fazendo pressão.
Bueno lo tengo decidido voy a por esta mira pero veo que quitáis la corredera aunque creo que no hace falta retirarla , gracias por el video voy a ver el otro y me decido por la 28 o por la 26 para mi glock 17 5 gen de co2.
I just saw your RUclips channel and you are not a great filmmaker, just like me. Instead of making useless comments that waste your time, you should use that energy to improve your videos.
this was the most helpful video compared to all others, thank you
4:48 what is that white sticker you put on it? Like foam?
The sticker is no longer necessary on the new adapters which are identifiable by the inscription "Fit Glock."
Great video! Do you think it can with stand the power of 45acp and 10mm? Would like to get one but afraid that mount will come out in time since the added weight that the beavertail needs
It will hold up for .45 ACP, but I am not sure if it will hold up for 10mm.
Is the plate/adaptor available also for glock 17 4th gen on the frenzy 1x17x24 and 1x20x26
All Glock 17, 34, 19 etc.. NOT SLIMLINE COMPATIBLE
For Frenzy-S 1x17x24 use adapter Vector Optics Footprint MAG / RMSc SKU SCRDM-09
red-dot-sight.eu/products/adaptateur-compatible-glock-empreinte-mag-rmrc-pour-frenzy-s
For Frenzy-X 1x20x28 use adapter Vector Optics Footprint TEK / Docter SKU SCRDM-01
red-dot-sight.eu/products/vector-optics-montage-type-rmr-pour-glock
For Frenzy-X 1x22x28 use adapter Vector Optics Footprint MOJ / RMR SKU SCRDM-08
red-dot-sight.eu/products/adaptateur-compatible-glock-empreinte-moj-rmr-pour-frenzy-xl
@@reddotsight1013 Do you know if this plate will also fit the vfc glock 19X?
How is your set-up holding up? Is it still tight and snug?
It is important to tighten all the screws to the correct torque of 1.5 Nm (11 lbf·in) and to apply blue Loctite (Loctite 243) on all the screws.
Thanks@@reddotsight1013 for the reply. I have the same mount with a Vector Optic Frenzy SCRD-1911 1x17x24 that I have been wanting to install for sometime now but hesitant to do it coz it might loosen up after extensive use. I am using a Roni Kit for my Glock in the meantime. I might go ahead and install it after seeing your video.
9:00 when I mount the base plate on the glock and screw it , the front lifts up. I can’t get it flat. can you help me with this
It is normal for the adapter to lift; it does not make contact with the front of the pistol slide. When you screw in the two small screws, the adapter must be parallel to the pistol slide.
Glock 19 gen 5 what Is best after market MOS adaptér fór frenzy x? Thanks
New from Vector Optics is an adapter for Glock 17 MOS, which is very well made. It is only compatible with Frenzy-S red dot sights (Footprint MAG / RMSc).
red-dot-sight.eu/products/adaptateur-compatible-glock-mos-empreinte-mag-rmsc-pour-frenzy-s
Hi... One question please, is there a stupid shut off after 90 min, so one has to turn it back on?
Is it included in the optic's package?
what did you put on the screws?
I am applying thread-locking fluid on the screws (Loctite 243).
@@reddotsight1013 thanks sir..
Loved it! I’m from India how do I get it?
Has it in any way cause any damage to the back side of slide? From the pressure or every round going off I'd assume there might be some type of contact?
I can get this mount, but what red dots can i buy that will fit this mount? Or is it only for vector optics?
How is the torque setting for the red dot mounting screws?!
I forgot to give the information 1.5 Nm (11 lbf inch)
@@reddotsight1013 Perfect.. thank you so much
No la puedo calibrar ... Corrijo los tornillos pero mueve el punto.. alguna recomendación?
Asegúrate de que el visor de punto rojo esté bien fijado al arma. Repositiona los tornillos en el punto medio de su recorrido para empezar los ajustes desde cero. Dispara 3 cartuchos, luego ajusta 1 graduación. Repite este proceso: dispara 3 cartuchos, ajusta, y así sucesivamente hasta obtener el resultado deseado. Si no logras calibrar el visor correctamente, te recomendaría llevarlo a un armero, quien podrá ajustarlo en aproximadamente 10 minutos. Buena suerte.
dis work for glock 17 gen4?
yes
@@reddotsight1013 Would it work for a BB GEN 4 too?
@@steveboone7390 It doesn't work with the blowback softair but it depends on the brand of your replica. You have to check if your BB is compatible with Glock sights
@@2sirb2383 Thanks
@@2sirb2383 it's not the softair but the co2 version that is by Umarex that shoots 4.5mm bbs and not 6mm bbs, so is a faithful replica of the realsteel version.
this slide mount "D1" does not work on the first gen glock 30 its to narrow, do you have anything that is a little wider to mount a vortex venom?
The D1 adapter is not compatible with models 20, 21, 20sf, 21sf, 29, 29sf, 30sf, G30. Vector Optics does not make other models.
Is it a must to glue the screws?
Yes, it is essential
@@reddotsight1013 but then is it still possible to remove the sight from the gun after the screws are glued? Also, how to change the battery in this case? (sorry i have not much idea about this red dot sight)
@@victorlcl With blue glue (Loctite 243/242) you can still unscrew the screws, but if you use red glue (Loctite 270/271) it will not be possible to unscrew the screws. For your information, the CR2032 battery has an operating life of 2 to 3 years.
@@reddotsight1013 i see. That's a very useful info! I'm gonna buy this red dot sight
Can you tell me if this optic is good for a Glock 20 Gen 4 and would the plate work for this particular gun?
The adapter used is exclusively compatible with non-MOS Glock models that have a slide width of 25.5 mm (1.0 inch). Your Glock 20 Gen4 has a slide width of 28.5 mm (1.12 inches). Therefore, this adapter is not suitable for your model of Glock. Regards, Raphael from RedDotSight.
This combo will work for a gen 2 glock 17?
Hello, do this work with glock 43x?
does not work with Slimline
the threads on my mounting kit for g17 stripped the first time i tried to screw it down today. i was using the same torque screwdriver in the video and i didnt even get close to 10 in.lbs. does this come under warranty because its a pretty serious quality flaw...
Is this compatible with a Glock 19 9mm Gen 3 California Compliant
does it fit on tisas px9 gen1..??
Price please and model detail
Hello. Can you give me wer you gonna buy the vector optic and plate. Because i have glock 19x and i want to have a red rot can you help me. Thanks
Hallo, ist es für Airsoft oder eine echte Waffe?
Ja, es ist für eine echte Waffe.
Does this red dot have parallax?
Parallax: 1.0 MOA at 100 yds. But is this important on a pistol for short range shooting !?
@@reddotsight1013 It will be used in a Glock G19 MOS.
I'm watching your video here from Brazil.
@@Moaximenes Don't miss the next video will be on mounting the Vector Optics 1x22x26 red dot on a Glock MOS.
how is the mount secure if you didnt screw it in?
Ao apertar os parafusos da placa,a chapinha que vai no lugar da alça de mira se levanta um pouco,ficando achatada entre a placa de cima e o slide,fazendo pressão.
Is the Vector Optik in this video compatible with Glock 42 ?
No, the kit is not compatible with the Slimline versions
@@reddotsight1013 do you know which with slimeline versions compatible?
@@pimelpirat1553 here is the link for the Slimline versions eu.glock.com/en/technology/slimline !!!!!!You should not use this kit for the Slimline!!!!
@@reddotsight1013 okay okay thanks
What is the name of that tool you are using? Like it
Torque Screwdriver Wrench
Hi , the plate / adaptor it is compatible with holosun 507 ecc .. ?
No, it's not compatible. This adapter is designed for the TEK/Docter footprint.
Will this work on a glock 35
yes, it works
@@reddotsight1013 wow thanks for your quick reply
wat model of vector optics
Vector Optics Frenzy 1x20x28 SCRD-35 / SCRD-40 + Adapter Glock Vector Optics
I'm surprised this thing takes a button battery.. you'd think these would all be rechargeable by now
The CR2032 battery has a life of 3 to 5 years. This is really not a problem.
@@reddotsight1013 thank you!
Also das mit dem doppelseitigen Klebeband kommt für mich nicht sehr hochwertig rüber.
Bei neuen Modellen mit dem Adapter mit der Aufschrift "Fits GLOCK" brauchen Sie das Klebeband nicht mehr zu verwenden.
Bueno lo tengo decidido voy a por esta mira pero veo que quitáis la corredera aunque creo que no hace falta retirarla , gracias por el video voy a ver el otro y me decido por la 28 o por la 26 para mi glock 17 5 gen de co2.
De hecho, no es necesario quitar la corredera 👍
@@reddotsight1013 ok realizado el pedido por Amazon , gracias
@@KatanaKatana1100 Gracias por su confianza 👌
Wenn ich das mir so ansehe, kommt das für mich nur mit einem Ersatzschlitten in Frage :-)
Excelente
Why was I recommended this
Sits too high over bore. There are better options out there.
Cuánto vale la mira óptica ?
Puede consultar nuestro sitio web.red-dot-sight.eu/
Buy optics ready.
Narration vs stupid music....lol...
I just saw your RUclips channel and you are not a great filmmaker, just like me. Instead of making useless comments that waste your time, you should use that energy to improve your videos.
Does it work for Glock 19 GEN 3 ?
Yes, it's compatible