Just discovered presta valves today. Completely stupid, schrader valves are universal and everywhere. Worked fine for 100+ years. Now ya need an new adapter or a pump, freaking stupid...
2ndAmendmentGlock: Presta valves were created because Shrader valves were too wide to accommodate onto the narrower rims created for road cyclists. Shrader valves created a weaker rim. Presta valves are narrower and leave more metal on rims. Horses worked fine for 100+ years and now we have other methods of transportation. It's about adapting to changing conditions which, hopefully, improve on previous ideas. Perhaps you may want to consider the advantages of researching the reasons for change prior to emoting so intensely. Lowers the blood pressure usually.
Agree with you. More of a bother than an improvement regardless of history of narrow rims, since fat tyre cycles and mt. Bikes with larger rims and tyres use them also ..
Thank you for posting this video! I bought an air inflator (compressor?) for my car tires that uses power from the cigarette lighter. It came with an adapter for both schrader and presta valves. I will try filling the tires on my bike (presta valves) by following your demo. Thanks again.
Thank you! Bought a bike this summer with the Presta valves and now I wish I had those adapters in my hand right now! Exactly what I was looking for here. :)
The trick about the caps actually does work if you need it to lol. I just did it because i didn't have any adapters. Now i can ride to the store to get adapters lol.
I saw another video sand they cut the cap but, they put the cap on upside down after they cut the cap. I don't know if it works on all presta valves but, it looked like it worked for him. I just got a bike with Presta valves and I was looking for how to get the gauge on my pump to read the pressure. It doesn't read the pressure until I start pumping it and I am pretty sure it's not accurate because it starts at zeo and only goes to 20 psi on the first pump when there air already in the tire. I had actually already bought those Presta valve adapters on Amazon and I tried to use them to get a gauge reading but, it didn't read until I pumped it even with the presta valve adapter. I did notice the valve could lock by twisting that one end but, I didn't know if that was supposed to do that until I saw your video. Thanks for showing us that we can loosen it to put air in the tire. I will try to unlock the presta valve and see if I can get a reading.
You cut the cap too short. It works if you only cut the very end off and push a drill bit or something through so it will screw on to the valve. You can't check the pressure unless there's a gauge on the inflation nozzle but you can get going again, for sure!
You did the Hack completely wrong. You cut the cap to short, as you need to flip the cap after cutting it, so it can screw in and seal it. This video is the proper way: ruclips.net/video/cYCFhz2LWIU/видео.html
The Adapter is a no brainer folks ..No one should purchase a tire with presto valves with out buying an adapter. The Hack here I thought was pure genius UNTIL you said it did not work. Why do you waste people's time ?
Stupid idea of changing the valve design. What you need to do is cut the cap with a blade just enough to go in upside down and it does work. Thats what i did and works really good.
Range77: If you believe that presta valves are the "stupidest thing ever" you must be living quite the protected life. Presta valves were created because Shrader valves were too wide to accommodate onto the narrower rims created for road cyclists. Shrader valves created a weaker rim. Presta valves are narrower and leave more metal on rims.
@@Ranger_k16 My first sentence was a reaction to the thought that you stated in your "stupidest thing ever" post. What I meant was that, since there are MANY stupider things, if you thought that presta valves were the stupidest of all, well, you must be quite sheltered because, after all, there are thousands of things that are far stupider and presta valves aren't stupid at all, for the reason I summarized in my first post to you here. Of course I was taking you literally. Do you now understand? (Sheesh....)
Presta valves were created because Shrader valves were too wide to accommodate onto the narrower rims created for road cyclists. Shrader valves created a weaker rim. Presta valves are narrower and leave more metal on rims. They are actually better than shrader in that respect.
@@lazurm You trying to outclass a suave, delectable stallion such as myself ? HA !!! I was raised in the gallows of fourewt & shemlechk. My skin is even tougher that of a top teir honey badger. Do your worst, peasant. 🧐
Horrible stupid Presta valves! My rear tire worked to air up but not the front. Brand new Ebike. there is not enough stem sticking up for the tire gauge to measure the pressure. it airs up just fine.
Presta valves were created because Shrader valves were too wide to accommodate onto the narrower rims created for road cyclists. Shrader valves created a weaker rim. Presta valves are narrower and leave more metal on rims.
@@lazurm you are correct, it's just that one of my kids bike has presta, hence we had to get an adaptor and struggle with that For professionals, I can see the benefits for sure
Read more about putting air in these silly things 👉 www.diymountainbike.com/how-inflate-presta-valve/
Just discovered presta valves today. Completely stupid, schrader valves are universal and everywhere. Worked fine for 100+ years. Now ya need an new adapter or a pump, freaking stupid...
2ndAmendmentGlock: Presta valves were created because Shrader valves were too wide to accommodate onto the narrower rims created for road cyclists. Shrader valves created a weaker rim. Presta valves are narrower and leave more metal on rims.
Horses worked fine for 100+ years and now we have other methods of transportation. It's about adapting to changing conditions which, hopefully, improve on previous ideas.
Perhaps you may want to consider the advantages of researching the reasons for change prior to emoting so intensely. Lowers the blood pressure usually.
Agree with you. More of a bother than an improvement regardless of history of narrow rims, since fat tyre cycles and mt. Bikes with larger rims and tyres use them also ..
Never seen these valves in my life , cheers for the cutting the valve cap in half , saved me walking home tonight
I'm glad it helped...🚴♂️🚴♂️🚴♂️
thank for spelling this out! i was about to buy a $30 kit to air up my presta valve tires. time to go to walmart!
should rename this video to GET A PUMP OR AN ADAPTER.
For real. Waste of time watching this bs video
nah he showed how to make ur own solution
Thanks for your comment you saved me 4 minutes of useless babble.
I live in the city so, I just walk to a nearby gas station
It's lighter lol
I didn't believe you at first so I watched the video and regretted it. Complete waste of time.
Thanks a lot for this, didn’t realize you needed to loosen the top piece and I was trying to fill it without doubt that🤦🏽♂️
At last the answer i was looking for, Thank you.
Glad I could help 🚴😃😃
Thank you for posting this video! I bought an air inflator (compressor?) for my car tires that uses power from the cigarette lighter. It came with an adapter for both schrader and presta valves. I will try filling the tires on my bike (presta valves) by following your demo. Thanks again.
Excellent, thanks for the comment. Those little adapters are super cheap I carry one on my bike. Happy Riding 🚴🚴
Thank you! Bought a bike this summer with the Presta valves and now I wish I had those adapters in my hand right now! Exactly what I was looking for here. :)
I did this hack and it worked. Not a lot of psi but enough to ride
Excellent, glad it helped.
Screw the cap on upside down after cutting the end off. The bottom end is just the right size :) hope this help someone
This is the exact video I needed
I had that issue today after getting my new tube and used my rubber-tipped air chuck blower. Thanks for the link to get adaptor.
The trick about the caps actually does work if you need it to lol. I just did it because i didn't have any adapters. Now i can ride to the store to get adapters lol.
Thanks for posting this video! Dummy me couldn't figure out how to pump the tires!
Before watching, increase playback speed to 1.75x.
😄😄😄😄
Presta valve should be phased out
I just wanted to say that I liked your video
Thanks!! 🚲
I saw another video sand they cut the cap but, they put the cap on upside down after they cut the cap. I don't know if it works on all presta valves but, it looked like it worked for him.
I just got a bike with Presta valves and I was looking for how to get the gauge on my pump to read the pressure. It doesn't read the pressure until I start pumping it and I am pretty sure it's not accurate because it starts at zeo and only goes to 20 psi on the first pump when there air already in the tire.
I had actually already bought those Presta valve adapters on Amazon and I tried to use them to get a gauge reading but, it didn't read until I pumped it even with the presta valve adapter. I did notice the valve could lock by twisting that one end but, I didn't know if that was supposed to do that until I saw your video. Thanks for showing us that we can loosen it to put air in the tire. I will try to unlock the presta valve and see if I can get a reading.
First thing I thought was he did it upside down
Awesome. What a life saver. Thank you for making this video.
You got it. You're welcome. Don't mention it. You bet.
It's a courtesy ! 👩🌾
I watched one of those hack vids about it. the cap you cut needed to be put on the presta upside down it seems.
Great comment, I'll have to try that out!! Thanks 🚴♂🚴♂
Thanks man. I guess it's the only way. I want to go for a bike ride but I always forget It has presta valves.
grest vid thanks, i will try this hack but with cutting the cap longer
🚴 sounds good 👍
I couldn't get that adapter trick to work either
I've been gathering up some valve caps to try it again. Stay tuned 🚴🚴
You cut the cap too short.
It works if you only cut the very end off and push a drill bit or something through so it will screw on to the valve.
You can't check the pressure unless there's a gauge on the inflation nozzle but you can get going again, for sure!
Why can't you just leave the adaptor?
You can, just remember to screw the valve back in.🚴🚴
Thank you for sharing it helped me.
Hey. Don't mention it.
You saved my day!
Why the heck did they switch to these valves? lol
Adapter, great thanks.
LOL...that adapter works better than the fitting on the bike pump.
I drove around for n hour n couldn't find a place to fill it up presta valve angry
I have the adaptor but I couldn't fill. Lol
Hi, remember before screwing the adaptor on loosen the little lock on the top of the valve, then give the valve a tap to make sure it's working.
Thank you for this Trying to figure out how the hell to do it 😂
I messed up a few of them.....so frustrating!
First video thanks
Thank you Brotha 🤙🏽
Tried the same adapter.. Doesn't work in gas station
Really?
Life was easier before presta valves. This is what happens when engineers get bored.
This is just what I needed, thx bro.
The problem with that adapter is it only screws to the very top thread not the body thread, for people that have tubeless tires....
5 minutes and 13 seconds with onne bit of useful information: "get an adapter".
Didn't work for me.
thanks for explaining in 5 mins what could have been shown in 30 seconds.
Thanks, I hope it helped 👍
Thank you so much!!!!!!!!!
First 2:10 is content-free.
Way cool.....
Thanks 🚴🚴
You did the Hack completely wrong. You cut the cap to short, as you need to flip the cap after cutting it, so it can screw in and seal it. This video is the proper way: ruclips.net/video/cYCFhz2LWIU/видео.html
Video could of been done with a screenshot
I think so too 🚴👍
I only heard this video, I was looking out my window.
The Adapter is a no brainer folks ..No one should purchase a tire with presto valves with out buying an adapter. The Hack here I thought was pure genius UNTIL you said it did not work. Why do you waste people's time ?
Bro seriously. I stoped at watching at 2:20, rest is history
Thanks, hopefully a couple minutes helped👍
On croirait qu'il a découvert le marteau a bomber le verre
POS system...tried to pump up tire and all air went out!
Ugh... I hate it when that happens....
Nice video
Yeah, yeah. Whatever you say chef frying pan 👩🍳
Stupid idea of changing the valve design. What you need to do is cut the cap with a blade just enough to go in upside down and it does work. Thats what i did and works really good.
Developed for skinny road bike wheels. The smaller hole in the rim makes a stronger wheel. I'm with you though kind of a pain.🚴
Why do they even make these stupid valves???? Whata headache
I know exactly what you mean....🚴
Its A Stupid Idea.A Perfect Example of.If it's not broke don't fix it.Pain In The Ass.Making Rocket Science out of Something Simple
Your exactly right 👍
thanks
Presta valves are the stupidest thing ever
Range77: If you believe that presta valves are the "stupidest thing ever" you must be living quite the protected life.
Presta valves were created because Shrader valves were too wide to accommodate onto the narrower rims created for road cyclists. Shrader valves created a weaker rim. Presta valves are narrower and leave more metal on rims.
@@lazurm because why? You didnt finish your thought and I'm open to hearing your point of view
@@Ranger_k16 My first sentence was a reaction to the thought that you stated in your "stupidest thing ever" post. What I meant was that, since there are MANY stupider things, if you thought that presta valves were the stupidest of all, well, you must be quite sheltered because, after all, there are thousands of things that are far stupider and presta valves aren't stupid at all, for the reason I summarized in my first post to you here. Of course I was taking you literally.
Do you now understand? (Sheesh....)
i see
👍🏻💯
No shit dude I wanted diy
What's the point, why do they use this garbage
Presta valves were created because Shrader valves were too wide to accommodate onto the narrower rims created for road cyclists. Shrader valves created a weaker rim. Presta valves are narrower and leave more metal on rims.
They are actually better than shrader in that respect.
@@lazurm ok
@@lazurm
Nah, son. That's been debunked.
One of those salior moon girls proved it wrong in the eighties.
@@Training_Wheels The 1880's?
@@lazurm
You trying to outclass a suave, delectable stallion such as myself ?
HA !!! I was raised in the gallows of fourewt & shemlechk. My skin is even tougher that of a top teir honey badger.
Do your worst, peasant. 🧐
B
C
Horrible stupid Presta valves! My rear tire worked to air up but not the front. Brand new Ebike. there is not enough stem sticking up for the tire gauge to measure the pressure. it airs up just fine.
Ugh...I know exactly what you're talking about.🚴🚴🚴
What a tool.
Perfect I agree!
It’s just a stupid valve and makes no sense
Get to the point!!! for christ sake!
I know to much blah blah....
I'm sorry, but presta valves are shite...
Presta valves were created because Shrader valves were too wide to accommodate onto the narrower rims created for road cyclists. Shrader valves created a weaker rim. Presta valves are narrower and leave more metal on rims.
@@lazurm you are correct, it's just that one of my kids bike has presta, hence we had to get an adaptor and struggle with that
For professionals, I can see the benefits for sure
My goodness none of these videos have been helpful 🤦🏻
Let me know what you want to see and I'll see if I can make it.🚴🚴
dumbest invation ever
Don't SAY stuff like that.
My wife doesn't like seeing mean comments and she might see yours, silly ! You're being SILLY !!
💵🐓🕺🏻
Get to the point already
Exactly...😎
Thanks for nothing! 😊
I understand 🚴♂️🚴♂️