Hii bro...... your project is working properly and your code also working Thank You so much And I have give your Channel reference in project report Thanks a lot brother
No dear I can't wait because I have to submit my project by 30 Sept But If this project will work then I will definatly try you currently working project in my major project
Sorry bro, i actually don't know about RCWL 1056 Radar Sensor ... But I'll make saperate Video on this Topic... ! Video Will be coming Soon !! 🌟 Stay Tuned and Subscribe For More !!! 👍
Hi sir I did all connections as u shown and also uploaded the code When I on switch the light will be on And when I give the motion front of sensor the lights will be off The system run in reverse
Ok Bro.. Change Light Connection To The Relay As Per Circuit Diagram... Means.. 1 Wire In "NC" & 2 Wire In "Com" Of Relay Output.. I hope You Understand 👍
Bro if two people entered then😅 what to do Oh got it we should use two ir sensor with a distance from one another right? But how to store the data of how many number of people entered
sir ye batain k light aese hoskti h k osko hm room men lagain or jb enter hon wo on hojaai or jb room se bahir niklen to wo off hojaai ?? how is it possible?
@@ProjectsPlannerand I have 1 more dought regarding to this project, Arduino ko alag se 5v ka current Dena padega ya wo bhi board se he current lega jaise bulb le rha h..
no bro.. sirf Arduino ko power supply dena hoga (Vin Pin) Se.. and relay Module ko 5 v supply Arduino se dena hoga (5V Pin) se... and humare bulb me 1 wire (netural wire -220v AC ) common rakh na hei AND 2 WIRE ( Phase wire) ko NO pin And COM pin se connect karna hei fir bulb ke sath connect karna hei. ! i hope apko samaj aagaya hoga ! contact me if you have still any problem/Dought . 👍
you should either check your Relay connections or change the time & sensitivity of the motion sensor by using its Potentiometer which placed on the sensor !
i used 4 channel relay instead of 2 channel .. i saw result in serial monitor in arduino ide .. but the light was connected to relay was not turning on .
how much motion sensor can detect the motion means if we wil place this system on upper wall so will it be detecting from the ground of the room means how much is the range of sensor of motion
and App iss Motion Sensor ki Sensitivity and Timings Bi Set Kar sakte ho.. Motion Sensor Ke Piche 2 Potentiometer Hoge jise uska Time And Sensitivity Change hogi.. !
so please check the connections from the relay side and also check the timing value in the motion sensor (check the Potentiometer value) for adjusting the timing.. it's value may be 0 !! if you have still any problem or any query then contact me !
BRO IT DOESNT WORK!! i connect everything correctly, the light blinks when the potentiometer on the pir sensor is changed and when it is on the right, it stops working.
bro There are two potentiometer on PIR Motion sensor.. 1 for sensitivity and 2 for Timing Delay so set the 1'st one in middle position and second one @ 25% for 4-10 min delay.. you should see the specifications of the Pir motion Sensor.. if you have still any problems plz . comment me.. !!
Hii bro...... your project is working properly and your code also working
Thank You so much
And I have give your Channel reference in project report
Thanks a lot brother
Thanks Bro for your Love.. 👍🤩❤️..
Hey uh i rlly need help did u use male to male jumper wires or female to male????
Please respond please
Male to Female !
hi bro your project will work properly
?
because i am going to purchase all required devices
yes Bro.. !! it Works Perfectly..
can you Wait For some Days.. I'm Now working on 16 Light control using motion senso.. so.
No dear I can't wait because I have to submit my project by 30 Sept
But If this project will work then I will definatly try you currently working project in my major project
Can i use microwave sensor RCWL 1056 instead of pir motion sensor that you used ?
Sorry bro, i actually don't know about RCWL 1056 Radar Sensor ... But I'll make saperate Video on this Topic... !
Video Will be coming Soon !! 🌟
Stay Tuned and Subscribe For More !!! 👍
can i use plug and wire that has on/off switch?
yes bro !!
Hi sir
I did all connections as u shown and also uploaded the code
When I on switch the light will be on
And when I give the motion front of sensor the lights will be off
The system run in reverse
Ok Bro.. Change Light Connection To The Relay As Per Circuit Diagram...
Means.. 1 Wire In "NC" & 2 Wire In "Com" Of Relay Output..
I hope You Understand 👍
@@ProjectsPlanner
I didn't understand. Can I contact in any social media like instagram or telegram
@@ProjectsPlanner could you please send your Instagram profile
Please reply me
sorry bro.. but i am not Using Instagram.. so!!
I will make your circuit as a project homework. I hope the codes are working 😊😊
I hope so too! 😂😃 ; Don't Worry it's completely Working!..
Bro i am going to give your reference in my project if this project will run
Because i am now working on it
Bro if two people entered then😅 what to do
Oh got it we should use two ir sensor with a distance from one another right? But how to store the data of how many number of people entered
sir ye batain k light aese hoskti h k osko hm room men lagain or jb enter hon wo on hojaai or jb room se bahir niklen to wo off hojaai
??
how is it possible?
Yes Bro.. Ye Possible hai .. 👍
@@ProjectsPlanner how, can you guide me please, can you give me your number or though this chat
How???@@ProjectsPlanner
Can you please explain
Sir,will this project come under IoT (internet of things) project?
Sir,is this a IoT project?
@@gjkeerthikeerthiganesan6600 ofcourse it would come under IOT..
@@chinmayjoshi5770 thankyou sir for ur reply
Yes !! ofcourse
All the codes are uploaded properly and the output has come correctly but the light is not turning off
Why the lights didn't turn off
Same issu with my project also
I have used it normally and coded too, Sam issues here
Same to the light is not switching off
2 relay module is necessary?? or instead of 2 relay can we use 1 relay module for it???
No Bro.. ! it's not necessary .. You can use 1 relay Module 👍
Best of luck !
@@ProjectsPlanner thanks a lot for your response
@@ProjectsPlannerand I have 1 more dought regarding to this project, Arduino ko alag se 5v ka current Dena padega ya wo bhi board se he current lega jaise bulb le rha h..
no bro.. sirf Arduino ko power supply dena hoga (Vin Pin) Se..
and relay Module ko 5 v supply Arduino se dena hoga (5V Pin) se...
and humare bulb me 1 wire (netural wire -220v AC ) common rakh na hei AND 2 WIRE ( Phase wire) ko NO pin And COM pin se connect karna hei fir bulb ke sath connect karna hei. !
i hope apko samaj aagaya hoga !
contact me if you have still any problem/Dought . 👍
@@ProjectsPlanner ohk bro now i understood.. 👍👍 thank you for your helpful reply :)
Hamara bulb off nahi ho raha continue chalu rah raha hai essie pata nahi chal raha ki sensor warking kr raha hai ya nahi
kya apki Relays Chal Rahi hai !! means usme Cliking ki avaj Aa rahi hei.. ??
i plug it in but the light bulb turned on without touching the sensor. what's the problem?
you should either check your Relay connections or change the time & sensitivity of the motion sensor by using its Potentiometer which placed on the sensor !
Instead of buld can we connect switch board?
yes bro.. you can connect with the switch board and control any electronic appliances!
Bro can we use nano arduino
Yes Bro... Nano & Uno Are Same In All Specification & Pins.. so you can Use Arduino Nano !
can I used esp32 instead of arduino?
Yes Bro. !!! if you want to make this project using Esp 32. i will make a video for you
@@ProjectsPlanner yes please..
i used 4 channel relay instead of 2 channel .. i saw result in serial monitor in arduino ide .. but the light was connected to relay was not turning on .
Check the Relay Pin Connections and use 5v Relay Module..
@@ProjectsPlanneri have done the same process bro . can you send your mail id or other contact . ill send my connection to you
Hiii... Bro I have uploaded the code properly and output has also come correctly but my light is blinking.. please give me solution bro
ok bro.. ! You Should Check Your Lights & Relay Connections ... !
Project budget how many cost?
max to max 500₹.. if you are using Arduino Uno..
you should use Arduino nano so that the overall cost of this project is under 400₹.. 👍
how much motion sensor can detect the motion means if we wil place this system on upper wall so will it be detecting from the ground of the room means how much is the range of sensor of motion
bro This Sensor Can Detect any Movement upto 20-25 Feet So.. You can Use For Your Wall . 👍 it will Work Properly.. !!
and App iss Motion Sensor ki Sensitivity and Timings Bi Set Kar sakte ho..
Motion Sensor Ke Piche 2 Potentiometer Hoge jise uska Time And Sensitivity Change hogi.. !
Can we Add Bluetooth module in this project?
Yes Bro.. You Can Add Bluetooth Module and Control your Room Lights💡Using Your Mobile 📱..
Can u explain the circuit diagram and the code 😄
I will make special Video for You.. 😁😜 👍
Can we connect ultrasonic sensor in instead of PIR motion sensor?
yes !!! bro
is this gonna work with a 200 watts light bulb?
yes bro
can i see the flow chart for this project?
You means Program Code ??
Hi bro my bulb is not switching off
so please check the connections from the relay side and also check the timing value in the motion sensor (check the Potentiometer value) for adjusting the timing.. it's value may be 0 !!
if you have still any problem or any query then contact me !
can you give me it's simulations.
Simulation means you want circuit diagram of this project ?
Where to type coding which software
Arduino-IDE Software for Programming.. !
BRO IT DOESNT WORK!! i connect everything correctly, the light blinks when the potentiometer on the pir sensor is changed and when it is on the right, it stops working.
bro There are two potentiometer on PIR Motion sensor.. 1 for sensitivity and 2 for Timing Delay so set the 1'st one in middle position and second one @ 25% for 4-10 min delay..
you should see the specifications of the Pir motion Sensor..
if you have still any problems plz . comment me.. !!
What is the purpose for this project
For thef Protection at night and Electricity Power Saving....
where is the code
In the Discription Box !..
sir pa pm naman ng program salamat po
what ?? i don't Understand .. please Comment In English / Hindi ...
Can I use urduino coding instead of using hard?
Means.. you want to use Arduino Programing instead of Arduino Hardware ??