Размер видео: 1280 X 720853 X 480640 X 360
Показать панель управления
Автовоспроизведение
Автоповтор
Thank you very much for this great task. I am creating a possible solution Video for my Onshape Community :) Thanks for your work.
Awesome good luck and also be sure to check out the practice models challenges at www.TooTallToby.com/practice
6:05 minutes using Alibre Expert, it took a few tries to get the orientation of the slot, holes and the 6mm end feature correctly orientated
Very nice!
17:20 mins, SW, Mass = 2981.16 grams
Nice job!
6 min to do it . Got the right answer (2981.15 g). Dragos
Very nice my friend!
2981.2 10:10min Plasticity
Awww yeah very nice Thomas!
I am a solidworks beginner, what is the best way to do the 6 holes? Took me a long time.
Use hole wizard, create hole, sketch array place 8 holes and skip 2 of the 8 to place 6 holes.
Here ya go @brendan2997 ruclips.net/video/zhN2hX1YcgQ/видео.htmlsi=ID5TFYnGMwqHP2q_
2981.154 g done in FreeCAD. forgot to take the time, but probably under 15 min. My 28 practice model 🙂 only 4 had incorrect mass and I couldn't figure out yet whats wrong
Nice job!! Go FreeCAD!!!
30 min approx. 2981.161 g. First try. (my best yet)
awww yeah nice job!!
Oh yes, 2981.161 grms, getting better about 15mins. Used ‘skip features’ for the first time 👍
Nice job Rob!
3325.31 g in 53 minutes! We'll get there, boys!
looks like I did some bad math early on. did plus 6m, should have gone minus 6m. model was too tall I think
Too tall - I know that plight!
2981.1613g in 9:13
Awww yea nice job!
seems like more than Tier 3 to me
lol - nice
2981.16 grams
nice!
2981.16 g
very nice!
Thank you very much for this great task. I am creating a possible solution Video for my Onshape Community :) Thanks for your work.
Awesome good luck and also be sure to check out the practice models challenges at www.TooTallToby.com/practice
6:05 minutes using Alibre Expert, it took a few tries to get the orientation of the slot, holes
and the 6mm end feature correctly orientated
Very nice!
17:20 mins, SW, Mass = 2981.16 grams
Nice job!
6 min to do it . Got the right answer (2981.15 g). Dragos
Very nice my friend!
2981.2 10:10min
Plasticity
Awww yeah very nice Thomas!
I am a solidworks beginner, what is the best way to do the 6 holes? Took me a long time.
Use hole wizard, create hole, sketch array place 8 holes and skip 2 of the 8 to place 6 holes.
Here ya go
@brendan2997 ruclips.net/video/zhN2hX1YcgQ/видео.htmlsi=ID5TFYnGMwqHP2q_
2981.154 g done in FreeCAD. forgot to take the time, but probably under 15 min. My 28 practice model 🙂 only 4 had incorrect mass and I couldn't figure out yet whats wrong
Nice job!! Go FreeCAD!!!
30 min approx. 2981.161 g. First try. (my best yet)
awww yeah nice job!!
Oh yes, 2981.161 grms, getting better about 15mins. Used ‘skip features’ for the first time 👍
Nice job Rob!
3325.31 g in 53 minutes! We'll get there, boys!
looks like I did some bad math early on. did plus 6m, should have gone minus 6m. model was too tall I think
Too tall - I know that plight!
2981.1613g in 9:13
Awww yea nice job!
seems like more than Tier 3 to me
lol - nice
2981.16 grams
nice!
2981.16 g
very nice!