@@the-happy-RC-flyer keep doing what you do! Even without many views you are the one video people find on what they're looking for some specific problem and you save them hours of painful time, your THAT great guy. Truly thank you yet again!!
Hey Thanks for your channel you helped me a lot. But now I have a question, after I update the firmware it reset the radio so I just had to create a new model again for may drone but now I don’t have slider’s working…I already search for it on the radio manu but can’t find anywhere the slider input to activate them. Thanks
Hi, I m new to this hobby. I followed your channel to setup my TX12 and binded with my drone but my Rekon35 is roll tilting to left as soon as I arm the motors (propellers touch the ground). Is it problem with my TX12 or its bad gyro calibration?
My TX12 'throttle' stick won't respond properly when adjusting left/right. When calibrating it only shows the stick moving a little (on the display) when in fact it's moving all the way left and right. The controller was working fine a week ago then it just started doing this. When viewing the channel monitor all the sticks go to +/- 100, but that one (left stick, left & right) goes -52 & -1. I can't see any way to reset this and have searched for hours online.. is it a hardware issue and needs to be taken apart to reset it or can it not be reset (potentiometer) ??
Yes calibrated multiple times, after reset everything on the radio too. Replacement gimbals aren’t expensive (shipping might be though 🙄), so I will probably just replace the gimbal and see then.
Try swap over the gimbals and see if the problem moves with the gimbal. Physically compare the gimbal which is ok with the other one. Check if the magnet has come loose.
Hi, I love your videos and I have a question. My gimballs are going in the middle automaticaly and I want to move them freely without them going in the middle. How can I do it ? Thanks
@@pyravi_ae you only have a friction plate on the 2 vertical sticks so you can open up the radio and remove the spring and then adjust the friction plate screw to get the feel you want. With some radios you can do this via screws you can access via holes in the back of your radio check your radios manual.
You will need to take the back off the TX12 to make the adjustments by doing up the screw on the throttle friction plate. This video will help you take your TX12 apart to tighten the tensioner. I wanted to make my throttle action stiffer so I add a strip of gaffer tap to the rotating plastic arm. ruclips.net/video/VtLd1QEOwMk/видео.html
@@the-happy-RC-flyer hello sir,i am facing a serious issue.chennels are changed and cant able to fly. I set chennel 3 as throttle but it changed to other like yaw.
@@Waikhom007 this difficult for me to diagnose without seeing your radio. Are you flying fixed wing or drones. You need to check your Rx channel order it should be AETR.
Hey bill I just got the tx 12 and the right gimbal is centered but if I barely just put my finger on it it says it’s 70% use to the left and Everytime I move it it just shoots left. I just calibrated it 3 times which is hard to do because of the problem. Do you know what may be wrong
Mason, I have never come across this problem before. I am hoping it is not a physical problem with the gimbal but let’s give this a go first. As your radio is new with no models let’s do a factory reset long press the SYS button and go to HARDWARE scroll down to Factory reset and reset your radio and then try calibrating your radio again. If you do have models on your TX12 please back it up first before factory resetting using OpenTX Companion.
@@the-happy-RC-flyer hey bill, thanks for the help but that didn’t work either I guess the potentiometer is just broken or something I’m just gonna end up returning it do you have any suggestions on new transmitters?
@@mason3851 the RadioMaster TX16S is a really nice radio but more expensive. I will be testing the RadioMaster T8 Pro soon but that is a game style controller. If you like the TX12 get a replacement I personally feel it is a good starter radio and you were just unlucky to get a faulty unit. I am sure this is not the problem but please check that on the gimbal that is messing around there has not been extreme expo set up on the input channel because that is what it sounds like it is doing.
@@mason3851 you need to check in Inputs and Mixes for the channel not operating correctly. In Inputs look under Curve Expo should be 0. In Mixes Curve default is Diff if Expo make sure it is 0. This is a long shot but worth checking.
And a very Happy New Year to you too. The ADC Filter helps smooth out the values which can jump around even when there is no movement of the analog source, basically averaging the values out. So if you viewed you mixes monitor you would see the values jumping around more if the ADC Filter is disabled.
@@SomeUserName_axe with EdgeTX the Devs have given us the option of setting a default for all models. So checking the ADC filter under SYS, Hardware will set the default ON. When you make a new model it will show global therefore ADC filter ON. You can then change this setting to OFF manually under the model settings if your new model is a drone.
Thank you. You’re the only one that calibrated those side sliders and the only one who didn’t move sticks in a 360 circle. Thank you.
Bless your soul. I never would have gotten half my stuff to work in this hobby if it was not for you! Thank you!
You are very welcome and I am happy my videos have helped you.
@@the-happy-RC-flyer keep doing what you do! Even without many views you are the one video people find on what they're looking for some specific problem and you save them hours of painful time, your THAT great guy. Truly thank you yet again!!
thanks! its really helped to me!
Hey
Thanks for your channel you helped me a lot.
But now I have a question, after I update the firmware it reset the radio so I just had to create a new model again for may drone but now I don’t have slider’s working…I already search for it on the radio manu but can’t find anywhere the slider input to activate them.
Thanks
Have you calibrated your radio making sure you move the sliders.
is it possibile to invert the throttle stick with the roll one? I like to have the throttle on the left stick
This video will help you change mode. ruclips.net/video/VtLd1QEOwMk/видео.htmlsi=EU23-A1rIzDv9zZh
Has anyone tried hanging pan tilt FPV cameras on sliders, is it convenient or not?
You could do that but would be difficult to operate with your FPV goggles on but not impossible.
Hi, I m new to this hobby. I followed your channel to setup my TX12 and binded with my drone but my Rekon35 is roll tilting to left as soon as I arm the motors (propellers touch the ground). Is it problem with my TX12 or its bad gyro calibration?
You need to make sure your propellers are on correctly and the motors are rotating the correct direction first.
@@the-happy-RC-flyer Thanks ! I solved the problem. My trim buttons were tottaly off, and I adjusted endpoint values in Betaflight.
My TX12 'throttle' stick won't respond properly when adjusting left/right. When calibrating it only shows the stick moving a little (on the display) when in fact it's moving all the way left and right. The controller was working fine a week ago then it just started doing this. When viewing the channel monitor all the sticks go to +/- 100, but that one (left stick, left & right) goes -52 & -1. I can't see any way to reset this and have searched for hours online.. is it a hardware issue and needs to be taken apart to reset it or can it not be reset (potentiometer) ??
Normally this would mean you need to calibrate the gimbals. I assume you have completed the calibration process?
Yes calibrated multiple times, after reset everything on the radio too.
Replacement gimbals aren’t expensive (shipping might be though 🙄), so I will probably just replace the gimbal and see then.
Try swap over the gimbals and see if the problem moves with the gimbal. Physically compare the gimbal which is ok with the other one. Check if the magnet has come loose.
Hi, I love your videos and I have a question. My gimballs are going in the middle automaticaly and I want to move them freely without them going in the middle. How can I do it ?
Thanks
Hi Pyra, I am pleased you are enjoying my videos makes it all worthwhile. Do you mean you do not want the throttle to center?
@@the-happy-RC-flyer Yea exactely
@@pyravi_ae you only have a friction plate on the 2 vertical sticks so you can open up the radio and remove the spring and then adjust the friction plate screw to get the feel you want. With some radios you can do this via screws you can access via holes in the back of your radio check your radios manual.
@@the-happy-RC-flyer Ok im gonna try it, thanks :)
Hey Bill how do I change throttle tension on this model.i find throttle gimbal stick quick loose and sloppy how do you tighten it?
You will need to take the back off the TX12 to make the adjustments by doing up the screw on the throttle friction plate.
This video will help you take your TX12 apart to tighten the tensioner. I wanted to make my throttle action stiffer so I add a strip of gaffer tap to the rotating plastic arm.
ruclips.net/video/VtLd1QEOwMk/видео.html
@@the-happy-RC-flyer that's great thanks
my tx12 not speak "armed or disarmed".
any tips?
James, do you have a SDCard in your TX12, you need one to have the SDCard contents to have the sounds.
@@the-happy-RC-flyer hello sir,i am facing a serious issue.chennels are changed and cant able to fly.
I set chennel 3 as throttle but it changed to other like yaw.
@@Waikhom007 this difficult for me to diagnose without seeing your radio. Are you flying fixed wing or drones. You need to check your Rx channel order it should be AETR.
@@the-happy-RC-flyer thanks sir for your valuable reply.
waiting your new upcoming videos sir👍
he has a video showing sounds
Hey bill I just got the tx 12 and the right gimbal is centered but if I barely just put my finger on it it says it’s 70% use to the left and Everytime I move it it just shoots left. I just calibrated it 3 times which is hard to do because of the problem. Do you know what may be wrong
Mason, I have never come across this problem before. I am hoping it is not a physical problem with the gimbal but let’s give this a go first. As your radio is new with no models let’s do a factory reset long press the SYS button and go to HARDWARE scroll down to Factory reset and reset your radio and then try calibrating your radio again. If you do have models on your TX12 please back it up first before factory resetting using OpenTX Companion.
@@the-happy-RC-flyer hey bill, thanks for the help but that didn’t work either I guess the potentiometer is just broken or something I’m just gonna end up returning it do you have any suggestions on new transmitters?
@@mason3851 the RadioMaster TX16S is a really nice radio but more expensive. I will be testing the RadioMaster T8 Pro soon but that is a game style controller. If you like the TX12 get a replacement I personally feel it is a good starter radio and you were just unlucky to get a faulty unit. I am sure this is not the problem but please check that on the gimbal that is messing around there has not been extreme expo set up on the input channel because that is what it sounds like it is doing.
@@the-happy-RC-flyer how do I go about checking the expo that you are talking about
@@mason3851 you need to check in Inputs and Mixes for the channel not operating correctly. In Inputs look under Curve Expo should be 0. In Mixes Curve default is Diff if Expo make sure it is 0. This is a long shot but worth checking.
Wishes for the new year Bill! I have a question about the ADC Filter, why is enabled?
And a very Happy New Year to you too.
The ADC Filter helps smooth out the values which can jump around even when there is no movement of the analog source, basically averaging the values out.
So if you viewed you mixes monitor you would see the values jumping around more if the ADC Filter is disabled.
@@the-happy-RC-flyer what is the difference in ADC filter between "on" and "global"?
@@SomeUserName_axe with EdgeTX the Devs have given us the option of setting a default for all models. So checking the ADC filter under SYS, Hardware will set the default ON. When you make a new model it will show global therefore ADC filter ON. You can then change this setting to OFF manually under the model settings if your new model is a drone.