Repair Attempt: "Fat" PS2 with No Display and Eject Button Not Working
HTML-код
- Опубликовано: 6 сен 2024
- Here I take a look at an original "fat" Playstation 2, which has no display and the eject button doesn't work.
Here's the link for PS2 motherboard fuse layouts: web.archive.or...
Note that the original site doesn't seem to want to load properly anymore, and that link goes to the Wayback Machine.
Note that I'm not a professional (in any sense of the word), and please don't mindlessly copy anything that I do.
Looking for something to read?
Check out my free SciFi/Fantasy books here: kpalexander.co...
Hope you enjoy them!
Also, do you have more money than good sense? If so, support my spurious work via Patreon at / discountsasquatch
As always, thanks for watching!
#playstation2 #consolerepair #righttorepair
![[Fix tutorial]Fix the fat ps2 console no display](http://i.ytimg.com/vi/fRCK8ygQI2U/mqdefault.jpg)
I remember when I had a PS2 when I was little, was 7 years old and had the fat model. It lasted for a few years until out of nowhere it not only stopped reading discs but then shortly after wouldn’t even turn on. However, my parents wound up getting my brothers and I a Slim model and that lasted much longer with no problems at all. Definitely the PS2 is a legendary console, it was my first PlayStation ever.
That BA chip is the CD/DVD Driver chip. Those become vulnerable to damage on specific models from reading burned discs as they put extra stress on it. Id pull the modchip as it is indeed a relic then try to get it working with the chip not in there. That was a very cheap chip back in the day. The DMS, and Matrix Infinity chips were the pinnacle. Modbos you'd by from Ali are just matrix clones these days. Re-check all the fuses since you let the smoke out. I have had a few successful repairs to these over the years with similar issues.
Hi there, and thanks for the great info! Will definitely be pulling the modchip and popping in a new BA. Quick question though, as it's been hard to find any solid documentation on this modchip: do you know if there any other modifications to the motherboard (that will also need to be undone) other than the soldered wires? (i.e. jumpered contacts, etc) Thanks again!
The modchip is over 20 yrs old, it’s the magic 3 modchip, that chip caused major problems back then, remove and replace the BA IC and also the other BA ic for the reset controller
Thanks for the info! Didn't realize that the other BA chip needed to be replaced as well.
@@DiscountSasquatch once the eject light not coming on and no display is shown, the driver IC which is the one next to the laser controls the other IC which is the controller IC they need to change, once that fuse is blown, those two IC need to change
I think that component that smoked out was the RF AMP which drives the laser? The fact it burnout seems really strange, I wonder if the mod chip went faulty and caused damage to the mechacon, Syscon or the drive assembly. Nice video!
Hi there, and thanks for the compliment!
I think you might be correct as to the mod chip being the culprit. We'll find out soon enough... well, as soon as I receive the replacement chips...
I'm just hoping nothing else is seriously damaged. As much as I realize we need "parts systems", I hate being the one to relegate a piece of hardware to that pile.
@@DiscountSasquatch I’ll look forward to the upcoming video! :D
Same here, can't wait for part 2 :)
Nice vid mate, im not an expert but i like to watch this kind of repair videos. You may wanna remove the broken chip and put some voltage on the board to see if is there any other shorts (overheating components) that may help you to trace any other failed component or maybe you already done it. looking forward for the pt2.
Thank you! Will definitely do that to see if I can track down any other gremlins on that board.
You should always remove the modchip first before doing anything else when you have an issue.
This was most likely caused by the solder joints coming loose (Or already being shorted when it was installed) and the chip shorting out.
The BA5815FM chip was already dead (No display and no eject) so no worries. Even losing the magic smoke usually isn't a big deal. I accidentally shorted out the equivalent chip with my multimeter probe on a PS2 slim and burned a massive hole in it while trying to diagnose no disc spin. Turned out, it was the issue all along, as replacing the burned chip fixed the original issue xD
Removing the modchip and replacing the BA5815FM (And the fuse if it's blown) would probably be enough to fix the console in case someone has the same issue
Could be an issue with the 47ohm Resistors near the GS GPU chip.
Iv had a nasty shock from one luckily I only touched the bottom of the board not the capacitor still felt like I was dieing for 3 days now I wear rubber gloves whenever I go near the power supplys lol
Ouch! Glad to hear you're okay, but yep, got to be careful anywhere around mains-level capacitors.
❤❤❤
Gosh why does it take two full months to send a fuse to you ???
Behold the wonder that is Ali Express...
the modchip burned that chip out desolder the modchip fix it then put decent modchip on be fine.
lol this my old ps2 I Modded to play different region games recognise my warranty sticker the Laser has been pot Tweet to high that the problem I bin it a Year ago as i couldn’t find a replacement laser
Hah, that's hilarious. Well... at least I know a little more about its history now.
change BA5815FM is faulty.100%sure
Why do you think so?
Well, pretty sure that's accurate since the chip has a giant scorch hole in it. The question is, did something else along the line cause it to blow?
@DiscountSasquatch did you ever figure out what was burning out the ba chips ? I have the same issue I put a new one almost got a DVD drive to work and it burned the fuse and chip again last night. Removed the chip again to get it working. A short from somewhere else I can't find it yet.
I have the same problem
Did you have a modchip as well in the system?
I like this video.
Sod-erd :-)
I'll have you know we speak the Queen's English in these parts! Long may she reign!
Not ejecting has nothing to do with av port 😂
this guy not know what hell is doing, laser´s fuses only envolved laser read disc system and not had nothing between them and video output so is useless try to fix that fuse, display problem could be by video chip GS is desolderied or video capacitors are brooken. one last thing, if you install a modchip this can destroy the console cuz works out of electrical limits and could damage bios or another chips like mechapwn so causes console not works ever more. remove the modchip and turn on console, maybe that can fix it.
And you're absolutely right about me not knowing what I'm doing. I've never worked on a PS2 before, and am learning along as I go. :)
Legit thanks for letting me know that the DVD fuse shouldn't affect the video though. I'll take another look at the video chip and its capacitors to see if I can spot anything on the next follow-up video, though I'm pretty sure that the modchip may have rendered this system a brick at this point.