😊 I see you're using the four drawer chuck that's good the long shaft with the grooves I just saw in the demonstration did you can you do it with the three jaw chuck I'm sure it would line up just as good as the four drawer just the idea and a suggestion thank you but it looks like you know what you're doing.
Este torno le da muy bien para esos pasos tan largos, el que tenemos en mi trabajo llega creo que a seis o siete mm de paso máximo, no sé si se puede ampliar eso. ..hace mucho que no hago cálculos y tengo olvidado esa parte de calcular los engranajes para obtener un determinado paso en la pieza
Jadi prinsipnya sama dengan membuat ulir 6 jalan ya sobat. Dan ujung mata pahat agak di serongkang ke arah gerakan nya. Matursuwun sanget. Sangat berguna . Salam hormat🙏
La parte que no comprendo es como dividió la entrada con ese dispositivo que monto al torno , como se llama la herramienta si alguien que conoce me ayuda ,por lo demás excelente trabajo
Porque usa los espejuelos en la camera y no en los ojos,areas no son ranges en zizA,son helices por rosca de paso 224mm.de paso a 4entradas Yuna Derecha,cruzada con una inquired lo hace como un effects de ziza.
Ensina como fazer um trabalho desse.. só colocar no RUclips e não falar nada. Nos que somos da área nunca vi um torno que corta esse diâmetro pelo menos os que já trabalhei
Thread cutting of high lead / pitch screws subjects the gear train to very high strain - because the machine spindle has to spin the lead screw many times faster. The addition of thread cutting forces - particularly when interrupted cutting while machining the opposite helix could result in damaging strain on the machine. (This can be felt when you try to turn the chuck manually while the lead screw half-nut is engaged - compare it with any other normal thread pitches - say upto 30mm pitch). A better way involving lesser strain on the gear train would be to keep the headstock in neutral and couple the lead screw to a seperate drive source. This would easily turn the headstock chuck with much less effort. You would be surprised when you can turn the lead screw by hand much easily.
@@alro2434 Actually brother, the gear train is already coupled between the main spindle and lead screw for the thread being cut. Even the existing lead screw and half nut are used, as set up. What is suggested is that a drive to the lead screw by a separate source would involve much less strain on the machine, due to the large reduction ratio when driven the other way from the lead screw. Just my observation shared.
Да...Обычная работа.😮Полное нарушение ТБ. НЕТ СТЕЛЛАЖЕЙ Всё валяется на полу.Без защитных очков.😢У нас бы оштрафовали и закрыли участок. Зачем выкладывать -,,как не надо работать".Выполнять надо требование ТБ.И не выкладывать эту ерунду.😃😂😅
Да...Обычная работа.😮Полное нарушение ТБ. НЕТ СТЕЛЛАЖЕЙ Всё валяется на полу.Без защитных очков.😢У нас бы оштрафовали и закрыли участок. Зачем выкладывать -,,как не надо работать".Выполнять надо требование ТБ.И не выкладывать эту ерунду.😃😂😅
у тебя проблемы со мной? Я не обижаю вас, я публикую только видео о своих действиях, я не заставляю вас лайкать мои видео и не заставляю вас смотреть мои видео.. Я вижу, вы всегда комментируете плохо.. такого рода это распространено в моей стране, мы работаем на полу, это стало нашей привычкой, если вам это не нравится, не смотрите мое видео..
![Run Away - Tzuyu(TWICE) ツウィ 쯔위 [Music Bank] | KBS WORLD TV 240906](http://i.ytimg.com/vi/KnHNNyAYiu0/mqdefault.jpg)
Gday, this job turned out spot on mate, thanks for sharing, cheers
Thanks brother matty's workshop
Vamos arriba hermano Messin muy bueno excelente, un Abrazo para ti y todos los hermanos Indoneses, José desde Florida Uruguay.
🤝🇺🇾🇺🇾 Jose Maciel Zamudio ♥️
@@Yantoo ❤❤
Gran trabajo!!!!! Saludos desde Buenos Aires, Argentina...
mantaap.....
teruslah semangat.
Terimakasih pak ❤️
😊 I see you're using the four drawer chuck that's good the long shaft with the grooves I just saw in the demonstration did you can you do it with the three jaw chuck I'm sure it would line up just as good as the four drawer just the idea and a suggestion thank you but it looks like you know what you're doing.
Muito lindo os videos trabalho nessa area também e aprender sempre torna vc melhor ok
Very good work, Yanto. ✊️
Best regards, Frank 🙋♂️🇩🇪
Thanks Frank 😁🙏♥️
Exelente trabajo.
Saludos desde Venezuela.
Excelente mi hermano Mesin me kede con la voca abierta felicidades 👏 y excelente trabajo bendiciones desde Monterrey México y su poderoso like 👍 😉
Fransisco Guerrero 😁♥️♥️
Este torno le da muy bien para esos pasos tan largos, el que tenemos en mi trabajo llega creo que a seis o siete mm de paso máximo, no sé si se puede ampliar eso. ..hace mucho que no hago cálculos y tengo olvidado esa parte de calcular los engranajes para obtener un determinado paso en la pieza
Nice work
Thanks brother ♥️
Keren Kang,
Suwun sharing kaweruh'e.
Sehat selalu lan tambah sukses ya,..
Common design used on lithographic presses as an ink oscillator roller.
Nice video
Thanks brother ♥️
Мне всегда, нравилось токарное дело , купил себе малый токарный станок, хорошо ещё резцы можно найти Советского производства .
٩
Excellent job. 👍👍👍
Jadi prinsipnya sama dengan membuat ulir 6 jalan ya sobat. Dan ujung mata pahat agak di serongkang ke arah gerakan nya. Matursuwun sanget. Sangat berguna . Salam hormat🙏
Nyimak cara membuat alur zig zag bolak balik, sangat bermanfaat. Salam sukses
good video mekanik mesin
Thanks brother ♥️
Espectacular amigachooo👌, saludos desde Argentina 🙋🏿
Antonio Ruis ❤️🤝
Sou fã dos vídeos que você publica.
Saudações do Brasil 🇧🇷
Terimakasih saudaraku Marcos Lourenco ♥️
Not thing new I made this Ty job, 20 years a go😮
Hello brother Yanto. Long and perfectly done job 👍💪
Thanks brother Dadier 😁♥️
Espectacular,de Diez !!
Thank you for your share amazing work
Thanks brother Mohamed♥️
Saludos cuates desde Chile 🇨🇱🇨🇱🇨🇱
Solo quiero saber cuánto divisiones hiciste en plato de cuatro garras y excelente trabajo
Công nghệ của you quá tuyệt vời 👍
La parte que no comprendo es como dividió la entrada con ese dispositivo que monto al torno , como se llama la herramienta si alguien que conoce me ayuda ,por lo demás excelente trabajo
nice dial indicator :D
Beau travail bravo
very nice work
Thanks brother Stewart ❤️
Terimakasih ILMU nya Kang 🙏🙏🙏
Yg di kasih kihat cara erpindahan pahat awal menyayat bahan....OM
Mas Yanto keren
Suwun mas e
c'est top 👍👍
Terimakasih saudaraku Franco ♥️
Wih mantep kang mesin bubutnya
Thank you for sharing👍
Thanks brother Rigo ♥️
Jos gandos mase
Like goodjob kawan
Este es un rodillo planchador de film
Cuando hay arrugas lo plancha ya q a la lamina lo lleva acia lo s costados
I want this knurling
Jo vagy !👍👍🇸🇰
Bang...lokasi dimana?kira2 bisa saya order roller conveyor seperti itu
Show de bola
Cuanto divisiones en plato de cuatro
Siiip mas ....
ماشاء الله ربي يبارك
Why would you groove a conveyor idler in the first place.
Porque usa los espejuelos en la camera y no en los ojos,areas no son ranges en zizA,son helices por rosca de paso 224mm.de paso a 4entradas Yuna Derecha,cruzada con una inquired lo hace como un effects de ziza.
Bang,,mo tanya sewaktu tuas rpm di netralin handel ulirnya di netralin juga gak...?
Tidak bang, tapi mesin harus kondisi mati..
用導螺桿的自動進刀囉
Bagaimana cara setting ulir kiri nya bang?
You are not able to get a little bit of vinegar..good for hair..you are not alone anymore
สุดยอดเลย
Bang bisa pesan cetakan aksesoris bentuk helem proyek untuk tima
Pointnya sekarang cari mesin yg ada pitch 225mm bosku
Лайк. Куда винт такой?
Делал такой для намотки тросса
это для прокатки панбеля 😁
@@Yantoo Рад за вас.
Jos mase
Maturnuwun mas, video jenengan nggih sae2..
Tp penontone mantap gone jenengan👍👍
Ох как неожиданно!)
Ensina como fazer um trabalho desse.. só colocar no RUclips e não falar nada. Nos que somos da área nunca vi um torno que corta esse diâmetro pelo menos os que já trabalhei
good job
Thanks brother
Please your Lathe Model?
Todo eso está muy bien. Lo que no veo bien es esa manera tan absurda de trabajar. No hay una mesa de trabajo
👏👏👏👏👏
Brawo
Untuk bubut 1 meter gk ada pitch segitu,😁
พี่ทำงานช่างกลึงมากี่ปีแล้วคับ
12 year old
@@Yantoo สุดยอดเลยครับพี่คือช่างที่มากด้วยประสบการณ์เเละมีฝีมือการกลึงขั้นเทพขอบคุณมากครับFC🇹🇭ติดตามชมตลอดไปครับ
Hi bro
👍🏻
I am India
I like superstar from India 😍😍
смещая малую продольную, делают обычно все .
Ini gerandong bosku ya
Lead screw!
☝️🤔👌🤘👍🖐️🙏🔥🌿🎲🧩♟️🏖️⛵🌈🍦🍨💻📖✍️
👍
BRAWO SUPER
jarak kisarnya berapa kak
Divideo ada bang, jarak kisar 224 mm
Thread cutting of high lead / pitch screws subjects the gear train to very high strain - because the machine spindle has to spin the lead screw many times faster. The addition of thread cutting forces - particularly when interrupted cutting while machining the opposite helix could result in damaging strain on the machine. (This can be felt when you try to turn the chuck manually while the lead screw half-nut is engaged - compare it with any other normal thread pitches - say upto 30mm pitch).
A better way involving lesser strain on the gear train would be to keep the headstock in neutral and couple the lead screw to a seperate drive source. This would easily turn the headstock chuck with much less effort. You would be surprised when you can turn the lead screw by hand much easily.
Thanks brother Ashish ❤️
Thanks, but they have to be coupled/synchronized, more parts more complicated, costing much more then a lead screw & half-nuts replacement.
@@alro2434 Actually brother, the gear train is already coupled between the main spindle and lead screw for the thread being cut. Even the existing lead screw and half nut are used, as set up. What is suggested is that a drive to the lead screw by a separate source would involve much less strain on the machine, due to the large reduction ratio when driven the other way from the lead screw.
Just my observation shared.
Do you live in?
Indonesia
Está bien pero comentaste mal en OJOTAS NO SE TRABAJA
👍👍😁🇧🇷
😯
Hello
Iam Letha machine operator please job
Om alamatnya daerah mana
Jogja bang
Jogjanya daerah mana om
Om boleh minta no telponnya atau nama bengkelnya apa mas sekarang saya di jogja. Terima kasih
Kiwi nggo rpm piro mas?
Lalu aku mas, nek ra 11 kayane 9
So the first step of the "how-to" would be to buy a lathe that can cut a 225mm pitch thread. Ok
Ulir
👍👍👍👏👏👏🛠🛠🛠
И чё? 🤣
這中心校的真隨便
Да...Обычная работа.😮Полное нарушение ТБ. НЕТ СТЕЛЛАЖЕЙ
Всё валяется на полу.Без защитных очков.😢У нас бы оштрафовали и закрыли участок.
Зачем выкладывать -,,как не надо работать".Выполнять надо требование ТБ.И не выкладывать эту ерунду.😃😂😅
Pagi bang , ada Facebook/ Instagram nya nga bang, saya izin mau nanya² seputar pembuatan alurnya bang🙌
Terimakasih sebelumnya bang
Trebuie sa știi meserie .Sa faci practica intr-o fabrica de prelucrări mecanice apoi devii meseriaș .asta nu se învata peste noapte
Nice video
Thanks brother
Да...Обычная работа.😮Полное нарушение ТБ. НЕТ СТЕЛЛАЖЕЙ
Всё валяется на полу.Без защитных очков.😢У нас бы оштрафовали и закрыли участок.
Зачем выкладывать -,,как не надо работать".Выполнять надо требование ТБ.И не выкладывать эту ерунду.😃😂😅
у тебя проблемы со мной? Я не обижаю вас, я публикую только видео о своих действиях, я не заставляю вас лайкать мои видео и не заставляю вас смотреть мои видео.. Я вижу, вы всегда комментируете плохо.. такого рода это распространено в моей стране, мы работаем на полу, это стало нашей привычкой, если вам это не нравится, не смотрите мое видео..
мы плохи в работе, но мы очень уважаем обычаи и привычки других стран.. потому что мы ценим адаб больше, чем знания