G'day Wayne, I used JMB and contacted Milan directly. They are perfect for the dle130. I was using a 28/10 for 3d and I now use a 28/12 for my IMAC competition flying. Would love to see your build when it is done.
@@joeytavora1270 Hi Joey Your videos have been a great help in the assembly on SW NG 104” A couple f items that could be highlighted: I assumed the elevator servos were mounted in the elevator sub assemblies so when looking for the rudder servo location I hacked away at what I thought it was only to find it is the optional elevator servo mounts in the fuselage (the factory places 2 arrows pointing in the same direction (what was that supposed to mean, E and R would have been better labelling :) ) The XT60 plywood holders are great but they only supplied 2 so if you run a dual battery system with ignition 3 would be required. The spinner template for the backplate is 30 degrees off the props I drilled and one pre drilled from DA (factory should include a note)- suppose it would be ok if you used their supplied template for both prop and spinner back plate. JMB canisters: Did you remove the coverings on the underside and use all 4 vent panels in order to mount the canisters? The 16 plastic rings - are this used to ‘surround and hold’ the canisters or are they for some other purpose - I can’t fathom yet as I don’t want to cut the covering without knowing (else I land up with un necessary holes (like my Fuse elevator hole which will get a decal to cover it). If you have any videos/pics of the canisters assembly/installation it would be greatly appreciated - JMB SET-3DHS-E540-106"-DLE130-REAR EXIT Once again thanks for the videos Cheers Wayne
Enjoyed all 3 videos on build. I noticed the black cover over the fuselage Area you cut out for engine cooling. Did you make that it did it come with kit. I ordered 104” edge expect similar set up
![YoungBoy Never Broke Again - Missing Everything [Official Video]](http://i.ytimg.com/vi/dTYeMZGzOzw/mqdefault.jpg)
What canisters were you waiting on for DLE130 - what size Falcon prop did you settle on - tks Wayne WRCS (busy with my build atm)
G'day Wayne, I used JMB and contacted Milan directly. They are perfect for the dle130. I was using a 28/10 for 3d and I now use a 28/12 for my IMAC competition flying. Would love to see your build when it is done.
@@joeytavora1270
Hi Joey
Your videos have been a great help in the assembly on SW NG 104”
A couple f items that could be highlighted:
I assumed the elevator servos were mounted in the elevator sub assemblies so when looking for the rudder servo location I hacked away at what I thought it was only to find it is the optional elevator servo mounts in the fuselage (the factory places 2 arrows pointing in the same direction (what was that supposed to mean, E and R would have been better labelling :) )
The XT60 plywood holders are great but they only supplied 2 so if you run a dual battery system with ignition 3 would be required.
The spinner template for the backplate is 30 degrees off the props I drilled and one pre drilled from DA (factory should include a note)- suppose it would be ok if you used their supplied template for both prop and spinner back plate.
JMB canisters:
Did you remove the coverings on the underside and use all 4 vent panels in order to mount the canisters?
The 16 plastic rings - are this used to ‘surround and hold’ the canisters or are they for some other purpose - I can’t fathom yet as I don’t want to cut the covering without knowing (else I land up with un necessary holes (like my Fuse elevator hole which will get a decal to cover it). If you have any videos/pics of the canisters assembly/installation it would be greatly appreciated -
JMB SET-3DHS-E540-106"-DLE130-REAR EXIT
Once again thanks for the videos
Cheers
Wayne
Enjoyed all 3 videos on build.
I noticed the black cover over the fuselage Area you cut out for engine cooling.
Did you make that it did it come with kit. I ordered 104” edge expect similar set up
Hey mate, the black cover is included. Thank you for the feedback, it is appreciated. Enjoy the build!
Great video! Which electric screwdriver are you using?
Es121 and than you for the feedback.
nice theta servos mate. C.H
First one I have tried, looks good on the bench!
como se LLAMA LA PIEZA