I have seen other videos if men using hot wire cutters to build wings for their RC planes but this is the only one so far that shows how one can separate the wing into sections! You also show how one can use a LiPO battery to heat the wire cutter! GREAT JOB!
You do fine work. I'm impressed. I'm concerned though that the unprotected foam wing surface is vulnerable to just about everything. A thin layer of covering will go a long way to protect all that work you did in making it.
Very interesting video for the construction of a wing, especially for how you show how to cut the hole for the spar. Well done and congratulations for this video🔝
Well done, it worked. Now to get some 1mm thick Balsa wood sheets and learn how to skin a wing. Your building skills will take off! One more tip, something we used to do with our old 2 piece wing gliders is use small cup hooks screwed into the plywood root rib and then use an elastic band between them to hold the wing on, not bolts and nuts. They can vibrate loose. if you are going to keep using bolts, at least put a piece of tape across the top to hold the wings on if the nuts come off. Happy flying mate.
How do you cut the wood parts? I really want to get into making rc planes and I'm like 50% ready and all I need is like a hot wire cutter and making these wood things. :-)
What glue are you using for polystyrene? I would need to glue large square 50 cm 50 cm subject to torsion. Any suggestions would be greatly appreciated. Cheers
Tenho um.radio desse não consigo faser essa configuração o seu está com a tela manchada não dá pra ver será que vc podia faser um.vedeo mais detalhado como vc configurou os flep separado dos ailleron brigado
0042 a wing's load-bearing main spar should be located at THIRTY percent of chord. CF is Heavier than wood and its use increases the auw of a model. the use of CF in the main wing makes the wing heavier and raises the location of the model's center of Mass (c-m). 0820 it is recommended that the mass of a quick connector be located at the servo, NOT at the control horn. 1312 the distance between the stabs and wing should be reduced by about two inches. there should be NO bends in a wire pushrod; except z-bends at the ends. 1407 when the model is level, the main landing gear should be located directly below the wing leading edge. googletranslate
I have seen other videos if men using hot wire cutters to build wings for their RC planes but this is the only one so far that shows how one can separate the wing into sections! You also show how one can use a LiPO battery to heat the wire cutter! GREAT JOB!
You do fine work. I'm impressed.
I'm concerned though that the unprotected foam wing surface is vulnerable to just about everything.
A thin layer of covering will go a long way to protect all that work you did in making it.
Packing tape works great on foam slope gliders. Tough as too
Ive also used brown paper and wallpaper glue. Then a coat of wood varnish makes it even glow fuel proof. Cheap
fantasticooo!!!
a good job
Damned clever. I never would have thought of that for the spars!!!
Nice upgrade. Good work and thank you for sharing!
A VERY fine piece of work and an excellent model. Many Thanks from the UK.
i maked my wings in 1972 with this system 😊
..No. .you MADE your [ model aircraft's ] wings in 1972 using this technique 😊
Good job, thanks for sharing!
Wow..this is a very informative video...lots of awesome tips...like the hot wire spar hole....genius....👍👍
Your building skills are amazing. Thanks for sharing.
8 for your landing
Thank you very much!
Hermoso trabajo. Felicitaciones
Beautiful job. Congratulations
Suuuper Video 👍 thank you
Excellent! Really liked the use of the battery charger for foam cutter power source.
What an excellent job!!
Glad you like it!
With landings like that, you could be a real pilot!
Nicely done! Thanks.
Very interesting video for the construction of a wing, especially for how you show how to cut the hole for the spar. Well done and congratulations for this video🔝
Glad it was helpful!
@@3JWings 🔝
Felicitaciones, buen trabajo. Desde General Rodríguez, Aeródromo EAA, Buenos Aires .Republica Argentina
Wow.. it's awesome.. god job .. saludos desde Chile. Creo que haré ese mismo proyecto.. muchas gracias por compartir tus conocimientos.. 🎉
that is a an excellent plane good work
10 for landing. Congratulations!
Jai Siya Ram 🙏🏻 amazing
Great work on the new wing, Jonu! Glad to see you putting your printer to use already in your plane projects :)
Excellent tutorial!
Great video, your channel really helped me get into the hobby
Glad to hear it!
Excellent! Fantastically great job. Thank you for your video. Liked and subscribed.
Asi hacia yo las alas de mis aviones hace 20 años 😅
Excellent work
great job
Very good work!
U gained a one more subscriber
😀
Nice work! 👍
Thanks for the visit
Excellent work as always 😊😊
Thank you! Cheers!
Un salut cordial....Succes în tote proectele
Very nice 👍👍👍 love you bro from Bangladesh 💕💕💕😊
Impressive bro ❤❤ 😊
very good
Very nice 👌 👍🏻 🙏
Great job,
Awesome job dude!
you keep missing the runway ; ) good job
genius
Very cool 👍
I will give you a LIKE because the video is edited like a PRO. I didn't know this channel I just saw it on my recommended videos.
Thanks for the sub!
Bro can u make a video on tools u r using like each n every tools.. Appreciated ur efforts.... ❤
I haven't flown my rc planes in two years, your video has got me interested again!
sweet job
Well done, it worked. Now to get some 1mm thick Balsa wood sheets and learn how to skin a wing. Your building skills will take off! One more tip, something we used to do with our old 2 piece wing gliders is use small cup hooks screwed into the plywood root rib and then use an elastic band between them to hold the wing on, not bolts and nuts. They can vibrate loose. if you are going to keep using bolts, at least put a piece of tape across the top to hold the wings on if the nuts come off. Happy flying mate.
Thank you sir for❤❤
You're welcome 😊
Fantastic
Had a great job bro do well i am waiting for your next videos
Thank you so much 😀
How was the dihedral dialed in? Were the carbon tubes shaped? I'm puzzled. Cool vid.
smart👍
smooth
Ước mơ của tôi!!
Landing: 9😊
10
Great vídeo.
Díameter hot wire?
👍👍👍
👌👌
do fusalage thanks, nice worj
hallo bro. can u make tutorial cutting foam using imax charging like what u use in this video??? please 🙏🙏
Very good ideas !!!
What kind of iron do you use for the wire cutting ?
Can you upload transmitter settings video
Wouldn't a wing nut be a better choice for the fastener of the wing mount? How long was the entire process of building the wing?
How do you cut the wood parts? I really want to get into making rc planes and I'm like 50% ready and all I need is like a hot wire cutter and making these wood things. :-)
Very nice...what is this place?
How you make hot wire cutter please guide
I didn't know you could use a B6Mini that way.
Me neither. On my B6AC, I don’t have the tool kits menu 😢
That carbon spar setup will probably snap as soon as you hit 90 G's.
100 , 50 , 40 , 30 , 20 , 10 , 5
What glue are you using for polystyrene? I would need to glue large square 50 cm 50 cm subject to torsion. Any suggestions would be greatly appreciated. Cheers
hello awesome video !!!!
Can you shared the Airfoild template please I would ike to try to do the plane ??
it see at 0:44 PLz!!
Did you use guitar string as wire cutter?
Nicrom wire
That creality printer is not a core xy but a bed slinger. :)
What tape did you use to connect the aeilerons to the wing
At 06:39
Nice video. What is the wire you used?
It's nichrome wire
Tenho um.radio desse não consigo faser essa configuração o seu está com a tela manchada não dá pra ver será que vc podia faser um.vedeo mais detalhado como vc configurou os flep separado dos ailleron brigado
What kind of wire is needed to do that?
Ni-chrome wire 18 gauge
Bro what kind of nicrome wire did you used for this hot wire cutter
I'd recommend to use gloves when working with epoxy
Bro make A380
Cool to watch thanks. Btw check out Ramy on his latest jet builds fowler flaps. Very similar to what you did. Laurie. NZ. 😊
I will check it out
I will check it out
Could you please list the names of the glues used with thermocol.
Bhai transmitter ki eskeren ko Keya hua
I think screen bleeding ho gai
@@3JWingstechno experiment extra RUclips Id
Вес какое аппарата?
Techno experiment extra RUclips Id
Number of that sandpaper
Hi...could you please share the airfoil template and motor cover STL file ?
ขอบคุณมากครับกับสาระเทคนิคและวิธีการทำเครื่องบินครับ❤❤❤
Green board name plzz
If you want a wing cutting CNC i have built one and is for sale, it will be a boast to your channel.
0042 a wing's load-bearing main spar should be located at THIRTY percent of chord. CF is Heavier than wood and its use increases the auw of a model. the use of CF in the main wing makes the wing heavier and raises the location of the model's center of Mass (c-m).
0820 it is recommended that the mass of a quick connector be located at the servo, NOT at the control horn.
1312 the distance between the stabs and wing should be reduced by about two inches. there should be NO bends in a wire pushrod; except z-bends at the ends.
1407 when the model is level, the main landing gear should be located directly below the wing leading edge. googletranslate
well done