Thank you so much. My Razer Kitty 7.1's kept popping and disconnecting and I ended up getting a new pair from Razer but I needed to cut the end off to ensure I couldn't use them again. I wanted to see if I could salvage them as I thought it could be a wire problem and from this video I managed to fix them and get them working again. Tysm. This was extremely helpful!
Really how You do it ? I'm having the same problema with mines , is like the aire but in the head set , I don't have the posibility to change them , but I wanted to fix them with. But i'm SO afraid to fail because is pretty different the Kitty headset to Kraken or normal headset. If You have any vídeo or si about how to fix them could You share it? Thank youuuuuu
LOL I had the exact same problem with my razer kitty... And I also had to cut the cord in order to get a new one. x3 I'm going to try to fix it because its always nice to have a backup headset.
If anyone has this problem: "Headphone occationally disconnecting from PC due to worn out / weak point in USB wire." I have a super easy fix, and just fixed mine. The reason this happens is inside the fabric insulation at certain points where there's too much movement, the wire starts to wear out and slowly rip, from being bent and twisted over and over. Razer intentionally manufactures folding / bending parts to manufacture this defect in. Try bending the wire around, and find out exactly where the fault is happening. Chances are it works just fine, until you bend a certain point in the wire and then it disconnects. If it's at the exit of the left ear cup you're going to have to disassemble, otherwise, that's not necessary. Plug the earphones in, and play test music. Hold the wire in a position where you're sure there's there's no disconnection! Then you're going to want to drip lots of superglue onto the fabric of the wire and allow it to soak it all up. As it cures it's going to become hard like an epoxy. Apply few coats and it'll turn into a really firm area and have 0 movement. This will "freeze" the weak point in the wire in shape so you don't have to cut the wire, and go through re-soldering. For me this was at the exit of the left ear-cup, it would constantly disconnect if I tilted my head. I de-assembled it, and applied plenty to about 1-2 inches of wire before the exit & after the exit. and also glued it to the exit, so there's no movement from the wire sliding in and out, and it works 10/10, no disconnects. Another perfectly good device saved from the landfill.
Mine kept popping and disconnecting 6 months after purchasing them and I was suspicious that it had been twisted and damaged because of how twisted the wire was when it arrived. I got a new pair from Razer, but after trying this fix on them before binning them for good, I managed to fix them and passed them onto my sister.
How about, instead of doing this, u just throw ur headset off the roof because i dont think anyone is going too really take apart their headset to do this
I have the kraken 7.1 chroma and the cable management inside them is a little bit more difficult, but after following your tutorial I did it! They work now!
I also have the chroma. Was it complicated? There seems to be a broken wire from what I can gather due to the sound and mic cutting whenever I nudge the cord. Is there anything I shouod be aware of before attempting this? (Worried I'll make it worse xD)
yes, you need to roll the wire in the earpiece one time. Most of the problems of the wires are in the start of the wire coming out of the earpiece. Its not a suberb fix but will never cut the sound again lol :D
@@Kecenaa did that actually work? i've been trying to contact razer to help me, but they didn't even reply lol. should i roll the wire in the earpiece?
I bought the Razer Kraken 7.1 Chroma about 3 years ago, and the headset sometimes turns off and back on when I nudge the cable. I am following your tutorial, but there is some weird white glue-like paste over the cables and the PCB. What should I do?
That is plastic glue that you should remove with a scalpel or knife. But be very gentle to avoid damage to the board. Then you will be able to change the cable.
@@snowkingcroJust a little update: I'm one step closer to my dream: having these headphones working again. I desoldered all the cables - but there's a problem. There are two black cables - one of them is a small one - negative and the other one is a big one - labeled SH. When I cut the cable open there was no big black cable though. Where did it go? Here are some pictures: imgur.com/a/O1BGyud
It's the shield... Well it's misterious that its not on the other side... If you have a multimeter, try to find a connection on the other side with the ground (black cable)
So I have Razer Krakens as well but they're designed for an Xbox One, not a PC, thus they use a 3.5mm jack and not a USB. Do you know if this would still work? Also, the solution in your video is meant to solve no audio in one cup, correct? You didn't exactly say what problem you are fixing.
Hi! What did you dip the exposed wires in exactly? Like what was that? Thats probably the only thing that didnt look straight forward to me I also wanted to know if this works for headphones with a mic attached
Hello, I have a Razer Kraven to which the cable broke, I cut it at the height of the cut and soldered it again in its place, the sound is perfect but the microphone picks up sounds too low, could it be because of the silicone that it covered the cables? .Is it necessary to put silicone on top of the pins?
@@snowkingcro hi bro, The same day I tried to re-solder the pins but the microphone was still listening low, what I think it may be are maybe put liquid silicone and separate more the cables from the microphone since I did not separate them much
@snowkingcro I also do not know if this affects, cut about 15cm of cable, the volume control is almost close to the hearing aids, I have cut a lot of cable extension, can that be the problem?
Hey this video was great man! My fiancé’s cats chewed up my cable to my Razer kraken 7.1 v2 and now they won’t work when I plug them in. I would try to repair them myself but I think I would just end up destroying them. I don’t even have a solder, is there a place I could take them to? So they can be fixed? Thanks
@@snowkingcro it can be applicable to kraken v2 chroma? I can't understand the order of the color, if i change i can broken the board? Thanks in advance!
Just write down the color order of the old cable before you solder the new one, and you should be fine... if you wire it wrong, they just wont work, you won't fry anything... 👍😁
So, i have razer kraken pro v.2 and the sound cracks, is "blurry" or comes out of one the two sides, depending on how i rotate the plug to the device, any suggestions? (i hope i was understandable, my english arent the best :) )
You can find it in near every store (even groceries)! This cable particulary was bought in a gaming store, because it's better quality and more elastic.
I tried to fix my razer adaro wire by soldering it, first and second wire is soldered but the third one burns out, looks like it was some silk like thing covered with thin metal wiring as cover. any ideas?
it's a sort of insulation on them. You should be able to remove it with a lgas ighter, light up just the tip, let it burn for a sec, or a couple of millimeters and bow it out, then you will be able to successfully solder it.
The real question would be, is it possible to add USB-C on the razer kraken ultimate/kitty, and make the cable detachable? That would fix the cable issue altogether by avoiding the bending on the headphone side of the cable, plus, you wouldn't have to disassemble the headset every time the cable breaks.
my cable just gets hot as soon as i plug it in i was listening to spotify playing games and then suddenly the audio stopped working, i then replugged the headset and it didnt work, it also didnt sense the usb cable, i started looking if there was any holes in the cable or anything and there was nothing, like 2 minutes later i touched the cable near the speaker (that goes into the speaker) and it was really warm (could say it was hot), i then unplugged it and it started cooling down, i plugged it into another usb port and same thing, it started getting hotter how do i fix this
After i opened mine i took out the paper thing covering the holes near the driver, after that , the sound was like .. there was no noise cancelation at all , no bass , and a open back kinda sound, i opened them again and covered the holes with a glue gun , but the same results, they dont have other problems, can you help ?
Hello, can you help me? When i touch the wire my Kraken 7.1 are turned off, I decided to replace the wire as on your video. Now my windows can't see my Kraken writes "Unknown Device"
+Can You Defeat check the wires.. Black and red are positive and negative poles, the other two are rx and tx data... Maybe you just soldered them the wrong way
The voltage positive and negative usualy go on outher sides (left and right) and the signals are the inner conections... If you wire it wrong, it wont work (but you won't brake it) so, if it doesn't work, just tri to turn it around... An be careful with your Soldering gun
@@CzlowiekKtor6NieMowi razer electra v2 usb cable has 5 different colour mini cable (green, black, yellow, red, white). but in video usb cable has only 4 diffrent colour. also there is no soldering for these 4 colour cable in video.
After 2 years of usage my Razer Kraken 7.1. V2 stopped being recognised. It said that it was an USB error. I tried everything and it still is not being detected by any device. Could this solve the problem ?
If you have no connection, this could help you solve your problem. Anyway, you cant go wrong... if it doesn't work, well, it didn't either, but if you get it to work... woooo hooo
What about the headset with the headphone jack instead? Mine isn't broken, but the cover is coming off of it and I bought heat shrink cable stuff, but the plug is so bulky that I can't get the right size onto it :/ I'd love to replace it with a braided cable for more durability.. My dog keeps stepping on it when it's on my headphone hook on the side of my desk and I have a 5 year old lol.
Well, in that case, i would rather buy a new headphone jack (NEUTRIK has the best) and if the cable isn't broken, just solder a new Jack. Hope it helps!
Well... 3.5mm could give you some audio output, but those phones need power in order to work (5v). maybe they could work but without light on them, but i'm not shure anymore...
Well haven't tested, but in general, all headphones powered over USB, which also have the connection over USB (integrated soundcard) work more or less the same way...
Im my opinion, those 4 shod be fine... Go, play around, there is no high voltage that could damage your headset, if you connect it wrong, they'll just will not work
What if U got ozone ekho h80 please Can u tell me how Can i fix this BC its has USB câble but also has that thing idk what it called u Can see if U look on the headset that volume +- and its broke from there so its ok if i change the while USB ?
Lol after 4 years my left speaker stop working it wasn.t the cable problem ,it was the speaker that cycle with magnet ,i.m looking for changeing my cable cuz it get hurt after 4 years anyway ,razer don.t deserve that money just for clarity ,we need durability
i wouldn't recommend a razer kraken headset. ive had so many issues with it since i got it. my mic stopped working, my right headphone is broken and it gets really hot on your ears.
@@justahumanwithamask4089 I had my pro v2 for almost 2 years and now my left speaker is kind of dead/alive... once I touch the cable a bit... thanks Razer :/
The audio dial on the cord isnt working (I can just scroll it over and over! And the sound coming out of it is overall garbage because of it!) If i can fix this easily PLEASE DONT HESITATE TO TELL ME HOW!!!!!!!!
Thank you so much. My Razer Kitty 7.1's kept popping and disconnecting and I ended up getting a new pair from Razer but I needed to cut the end off to ensure I couldn't use them again. I wanted to see if I could salvage them as I thought it could be a wire problem and from this video I managed to fix them and get them working again. Tysm. This was extremely helpful!
I'm having the same problem with mine and they're going to send me a replacement, it's good to know that I can possibly salvage my old pair though
Really how You do it ? I'm having the same problema with mines , is like the aire but in the head set , I don't have the posibility to change them , but I wanted to fix them with. But i'm SO afraid to fail because is pretty different the Kitty headset to Kraken or normal headset. If You have any vídeo or si about how to fix them could You share it? Thank youuuuuu
LOL I had the exact same problem with my razer kitty... And I also had to cut the cord in order to get a new one. x3 I'm going to try to fix it because its always nice to have a backup headset.
@@Sopherian i have the same problem with my razer kraken ultimate
If anyone has this problem: "Headphone occationally disconnecting from PC due to worn out / weak point in USB wire."
I have a super easy fix, and just fixed mine. The reason this happens is inside the fabric insulation at certain points where there's too much movement, the wire starts to wear out and slowly rip, from being bent and twisted over and over. Razer intentionally manufactures folding / bending parts to manufacture this defect in. Try bending the wire around, and find out exactly where the fault is happening. Chances are it works just fine, until you bend a certain point in the wire and then it disconnects.
If it's at the exit of the left ear cup you're going to have to disassemble, otherwise, that's not necessary. Plug the earphones in, and play test music. Hold the wire in a position where you're sure there's there's no disconnection! Then you're going to want to drip lots of superglue onto the fabric of the wire and allow it to soak it all up. As it cures it's going to become hard like an epoxy. Apply few coats and it'll turn into a really firm area and have 0 movement. This will "freeze" the weak point in the wire in shape so you don't have to cut the wire, and go through re-soldering.
For me this was at the exit of the left ear-cup, it would constantly disconnect if I tilted my head. I de-assembled it, and applied plenty to about 1-2 inches of wire before the exit & after the exit. and also glued it to the exit, so there's no movement from the wire sliding in and out, and it works 10/10, no disconnects. Another perfectly good device saved from the landfill.
Mine kept popping and disconnecting 6 months after purchasing them and I was suspicious that it had been twisted and damaged because of how twisted the wire was when it arrived. I got a new pair from Razer, but after trying this fix on them before binning them for good, I managed to fix them and passed them onto my sister.
thanks, man
what if its multiple spots or where the cable connects
not the fix i was looking for
same
Thanks to this video I was able to save some money, and I was able to recover my Kraken 7.1! Thanks!
Thanks, glad that i helped!
What cream are you dipping the wire endings in and is it important in the process ?
It's soldering flux.
it's not mandatory, but the soldering is easyer with it.
Hey, suddenly the left side of my kraken stopped working... Any ideas how I can try to fix it ?
+Eduardo Tamaki well, my opinion is that you have the same problem i had on those phones i recorded. There's an interruption on the cable somewhere...
Seguro?, tengo el mismo problema. Revise la placa y esta bien.
How about, instead of doing this, u just throw ur headset off the roof because i dont think anyone is going too really take apart their headset to do this
@@matthew.6994wrong! I just bought 2 broken razer krakens off eBay fixed them and resold them for +100 usd each because I got them so cheap lol
@@matthew.6994 i will
"Easy"
If you know how to hold a screwdriver and a soldering iron its easy.
I have the kraken 7.1 chroma and the cable management inside them is a little bit more difficult, but after following your tutorial I did it! They work now!
I also have the chroma. Was it complicated? There seems to be a broken wire from what I can gather due to the sound and mic cutting whenever I nudge the cord. Is there anything I shouod be aware of before attempting this? (Worried I'll make it worse xD)
yes, you need to roll the wire in the earpiece one time. Most of the problems of the wires are in the start of the wire coming out of the earpiece. Its not a suberb fix but will never cut the sound again lol :D
@@Kecenaa did that actually work? i've been trying to contact razer to help me, but they didn't even reply lol. should i roll the wire in the earpiece?
I bought the Razer Kraken 7.1 Chroma about 3 years ago, and the headset sometimes turns off and back on when I nudge the cable. I am following your tutorial, but there is some weird white glue-like paste over the cables and the PCB. What should I do?
That is plastic glue that you should remove with a scalpel or knife. But be very gentle to avoid damage to the board. Then you will be able to change the cable.
@@snowkingcro Alright. Thanks for your help.
@@snowkingcroJust a little update: I'm one step closer to my dream: having these headphones working again. I desoldered all the cables - but there's a problem. There are two black cables - one of them is a small one - negative and the other one is a big one - labeled SH. When I cut the cable open there was no big black cable though. Where did it go? Here are some pictures: imgur.com/a/O1BGyud
It's the shield... Well it's misterious that its not on the other side... If you have a multimeter, try to find a connection on the other side with the ground (black cable)
So I have Razer Krakens as well but they're designed for an Xbox One, not a PC, thus they use a 3.5mm jack and not a USB. Do you know if this would still work? Also, the solution in your video is meant to solve no audio in one cup, correct? You didn't exactly say what problem you are fixing.
did you end up fixing them?
Hi! What did you dip the exposed wires in exactly? Like what was that? Thats probably the only thing that didnt look straight forward to me
I also wanted to know if this works for headphones with a mic attached
It is soldering flux. it is used to get the solder stick better to the wire.
It works with all soldering joints
@@snowkingcro oh!! thank youu
does it still work with synapse and does stereo audio still work?
Hello, I have a Razer Kraven to which the cable broke, I cut it at the height of the cut and soldered it again in its place, the sound is perfect but the microphone picks up sounds too low, could it be because of the silicone that it covered the cables? .Is it necessary to put silicone on top of the pins?
Maybe you just didn't solder it well, try resoldering the contacts.
@@snowkingcro hi bro, The same day I tried to re-solder the pins but the microphone was still listening low, what I think it may be are maybe put liquid silicone and separate more the cables from the microphone since I did not separate them much
Maybe it's interference between the wires since they're not as far apart as they were originally and the silicone is missing.
@snowkingcro I also do not know if this affects, cut about 15cm of cable, the volume control is almost close to the hearing aids, I have cut a lot of cable extension, can that be the problem?
Hey this video was great man! My fiancé’s cats chewed up my cable to my Razer kraken 7.1 v2 and now they won’t work when I plug them in. I would try to repair them myself but I think I would just end up destroying them. I don’t even have a solder, is there a place I could take them to? So they can be fixed? Thanks
Well, i think that any electronic service shop could handle them... But it depends on your location...
snowkingcro thanks for the reply! Ok well I’m in California. I’ll look into an electronic service spot.
@@eliashernandez4416 How did it go? I find myself in the same situation but I've already messed up once.
did you use simple micro usb random cable?
Well, yes, just simple random... The only thing, I've searched a nice silicone one that is a bit softer...
I have a few questions. It could be any usb cable? What did u connect it to at the end
Yes, any usb... I prefer more flexible, with silicone in it... It's durable. The black and red arevfor power, other two for signal.
@@snowkingcro it can be applicable to kraken v2 chroma? I can't understand the order of the color, if i change i can broken the board? Thanks in advance!
Just write down the color order of the old cable before you solder the new one, and you should be fine... if you wire it wrong, they just wont work, you won't fry anything... 👍😁
Any idea what i should do when my left side only works if i bent the cable?, i dont have the usb version
change the cable. you don't need the usb, just the 3.5mm
So, i have razer kraken pro v.2 and the sound cracks, is "blurry" or comes out of one the two sides, depending on how i rotate the plug to the device, any suggestions? (i hope i was understandable, my english arent the best :) )
Hi, I just want to know, did you buy the headband separately? If so from where?!
No, it came this way.
@@snowkingcro is it the forged edition?
Sorry, don't know... just had them in for repair, a friend uses them, but which version... realy don't know
@@snowkingcro Ah okey.. Thanks anyway ☺
Will this work with the other plug? the pin type.
No, they are USB powered, so only usb
is there a way to buy the speaker ?
Mine is already broken, left speaker has less bass than the right one
I havent found any yet...
Any idea on what the fix is for the speaker on side with the volume control not working ?
Hello, please send me a link to the store where I can buy this cable
It's basically any store that sells USB cables
where did u buy this cabel?
You can find it in near every store (even groceries)! This cable particulary was bought in a gaming store, because it's better quality and more elastic.
how about Kraken with jack 3,5mm wire? can I replace it with male to male jack 3,5mm (cutting the other side)?
Yes, this would be the easyest way!
May one ask what tools you used?
Regular screwdrivers, some soldering flux and so on...
I tried to fix my razer adaro wire by soldering it, first and second wire is soldered but the third one burns out, looks like it was some silk like thing covered with thin metal wiring as cover. any ideas?
it's a sort of insulation on them.
You should be able to remove it with a lgas ighter, light up just the tip, let it burn for a sec, or a couple of millimeters and bow it out, then you will be able to successfully solder it.
The real question would be, is it possible to add USB-C on the razer kraken ultimate/kitty, and make the cable detachable? That would fix the cable issue altogether by avoiding the bending on the headphone side of the cable, plus, you wouldn't have to disassemble the headset every time the cable breaks.
It's quiet possible to do this kind of upgrade/conversion.. just a little bit of skill with the soldering iron... :)
Hi could you tell me left to right correct way to soldered each that small colored cable
I'm sorry, but it depends on the layout of your board.
The colours go the same way you remove the old cables.
Oh okay thanks a lot for the information.
my cable just gets hot as soon as i plug it in
i was listening to spotify playing games and then suddenly the audio stopped working, i then replugged the headset and it didnt work, it also didnt sense the usb cable, i started looking if there was any holes in the cable or anything and there was nothing, like 2 minutes later i touched the cable near the speaker (that goes into the speaker) and it was really warm (could say it was hot), i then unplugged it and it started cooling down, i plugged it into another usb port and same thing, it started getting hotter
how do i fix this
I can’t find a replacement. Where should I go to get one?
any store that sell usb cables for phone chargeing
Is this working for the v2? i have te same problem, ty for the video.
Can you give us the flat of the mainboard and conections?
Ty so much, dude
I fixed the V2 the same way.
Good luck!
@@snowkingcro ty so much bro
@@alexismanuel1634 yo did you manage to fix them? i know its a year later but i was just wondering because i also. have the V2
After i opened mine i took out the paper thing covering the holes near the driver, after that , the sound was like .. there was no noise cancelation at all , no bass , and a open back kinda sound, i opened them again and covered the holes with a glue gun , but the same results, they dont have other problems, can you help ?
i just want to know the places /colors of cables in the speaker thing they got disconnected and didnt knw how to connect them back
From left to right: Red White Green Black
Bhai ye wire kidr sa buy ki ha apna??
Which wire? my translate does not work well, sorry
Hello, can you help me? When i touch the wire my Kraken 7.1 are turned off,
I decided to replace the wire as on your video. Now my windows can't see my Kraken writes "Unknown Device"
+Can You Defeat check the wires.. Black and red are positive and negative poles, the other two are rx and tx data... Maybe you just soldered them the wrong way
Yes, thanks, I got the wrong soldered
hi, any usb cable is good for replace? and i don't have welder what can i do?
+ElJuanchoEz well without any soldering iron... You don't have many options
Soldering Iorn*
Lo arreglaste?
soldering iron*
Thanks for the update... 👍😉
So black from the new usb goes to GND?
Yes
@@snowkingcro what about "VC" ?
The voltage positive and negative usualy go on outher sides (left and right) and the signals are the inner conections...
If you wire it wrong, it wont work (but you won't brake it) so, if it doesn't work, just tri to turn it around... An be careful with your Soldering gun
Will this work with Razer Electra V2 USB aswell?
Sorry, i don't know. I didn't had the chance to meet them yet.
@@snowkingcro Well, it did work with the same method as in video. It was bit different inside of Electra but method all the same!
That's good to know. Thank you.
@@CzlowiekKtor6NieMowi razer electra v2 usb cable has 5 different colour mini cable (green, black, yellow, red, white). but in video usb cable has only 4 diffrent colour. also there is no soldering for these 4 colour cable in video.
After 2 years of usage my Razer Kraken 7.1. V2 stopped being recognised. It said that it was an USB error. I tried everything and it still is not being detected by any device. Could this solve the problem ?
If you have no connection, this could help you solve your problem.
Anyway, you cant go wrong... if it doesn't work, well, it didn't either, but if you get it to work... woooo hooo
@@snowkingcro when you soldered the new cable do you lost audio quality ?
works with synapse?
Sorry, haven't tried yet
What about the headset with the headphone jack instead? Mine isn't broken, but the cover is coming off of it and I bought heat shrink cable stuff, but the plug is so bulky that I can't get the right size onto it :/ I'd love to replace it with a braided cable for more durability.. My dog keeps stepping on it when it's on my headphone hook on the side of my desk and I have a 5 year old lol.
Well, in that case, i would rather buy a new headphone jack (NEUTRIK has the best) and if the cable isn't broken, just solder a new Jack. Hope it helps!
@@snowkingcro Thanks so much! It's one of those "L-shaped" jacks so it's impossible to get heatshrink tubing over
Yeah, i know... Been there, done that... 😒
Does it have to be a usb, can it be a 3.5 mm headphone jack
No, because the headphones need power to work, and basically, they are a soundcard... Sort of...
@@snowkingcro so it works with 3.5mm?
Well... 3.5mm could give you some audio output, but those phones need power in order to work (5v).
maybe they could work but without light on them, but i'm not shure anymore...
It’s the mute button itself on my mic that broke, the headphones work the mic works but they’re stuck on mute and I cannot unmute :(
I think that it would be easy to open up the switch and wiggle the button out
i have the razer kraken 7.1 chroma is same?
+ElJuanchoEz it should be
i have no soder
Does it work with ultimate?
Well haven't tested, but in general, all headphones powered over USB, which also have the connection over USB (integrated soundcard) work more or less the same way...
@@snowkingcro Yeah makes sense :) But i really hope i wont need this guide
how i soilder the new cable? with the colors? red with red black with black?
+ElJuanchoEz red and black are mandatory, other colors, if not working, you can try to switch them
you know i think i can live with only one side of my ehadset working
this made me laugh out loud
I have a Razer kraken tournament edition and the cord got chewed through, does anybody know if I can buy a replacement cord for it?
Yes, any USB cable is fine
and what about hand band replacement?
The cable on these Razer headsets are terrible, the 2nd set has just broken the wires, they don't even last the warranty period
I bought a Razer kraken pro v2 less than a month ago and the left speaker already stopped working
What if my usb doesn’t have 5 wires just 1 black a yellow a red and a white
Well, black and red are the power wires (positive and negative) so the yelow and white should be left and right speakers.
snowkingcro so do I need all 5 wires or just the 4 I have
Im my opinion, those 4 shod be fine... Go, play around, there is no high voltage that could damage your headset, if you connect it wrong, they'll just will not work
Where'd you get the music from mate?
PixelDaFox RUclips, those free audio clips
What if U got ozone ekho h80 please Can u tell me how Can i fix this BC its has USB câble but also has that thing idk what it called u Can see if U look on the headset that volume +- and its broke from there so its ok if i change the while USB ?
Sorry mate, i can't help you with that
So i can do this with a cable from another pair of headset which have volume buttons incorporate on cable ?
Shure you can!
where i can get a cable?
It's a common USB cable, you can get it anywhere!
I just tried to find a more flexible, but any usb is fine
snowkingcro can you give me a link ?
you can try this one www.ebay.com/itm/164167376246
my cable is all sorts of messed up
yeah... mine got twisted so bad overtime the left speaker only works sometimes.
Wasn't what i was looking for...
sorry
You are a legend Thank you so much!!!!!!!!!!!!!!!!!!!!!!!!!! I was so scared and I didn't know what to do and now you saved me!!!!!!!!!!1
+inesta 987 thanks...
I bought the razer chrome kraken 7.1 I turned it on, listened to the sound and then it stopped recognizing no more. What can be, will be the cable
It coud be the cable... But, if you boughtnit just recently, try to change it in your store for a new one.
@@snowkingcro Do you have any video teaching how to open the cable part.
Sorry, i haven't.
Fix microphone pls
My mic doesn't work and I hear a little rock inside my left earphone please help
Did you try to open it? Maybe you put to much solder, so it broke off
thank you. my right earcup just stopped working and i noticed my cable was getting out of its place cause of my cat.
thanks for the video mate
Do i need to use the paste?
No, but i would recomend it!
@@snowkingcro what is that paste tho?
soldering paste, or flux...
Good vid, but it would be better with full pcb bord displayed
Yes, it would... but I was a newbie in repairs... 😊
Please tell me how to fix the circuit
what is this in blue container? 2:03
It is soldering flux. It's used for better soldering connection.
mmm this is easy if you know where to solder each cable. You did not mention it
Well, just mark wich cable you remove, then solder the same colour of the new cable back... Easy! 😎
Lol after 4 years my left speaker stop working it wasn.t the cable problem ,it was the speaker that cycle with magnet ,i.m looking for changeing my cable cuz it get hurt after 4 years anyway ,razer don.t deserve that money just for clarity ,we need durability
i wouldn't recommend a razer kraken headset. ive had so many issues with it since i got it. my mic stopped working, my right headphone is broken and it gets really hot on your ears.
btw ive only had this headset for a month
@@exwt same with me, I have the Razer kraken pro v2 and the left speaker just stopped working after a month.
@@justahumanwithamask4089 I had my pro v2 for almost 2 years and now my left speaker is kind of dead/alive... once I touch the cable a bit... thanks Razer :/
I have it as AUX cable
So if I change the wire it doesn't affect the quality right?
Yes, the quality will not change, however, if you wire it wrong, you will get nothing
what is this paste 2:01?
+ElJuanchoEz soldering paste
Thermal paste?
@@chickenadams9365 soldering paste lol
Nope
Eu tenho um Kraken 7.1 v2, posso usar esse método nele?
Pode sim, acabei de fazer com o meu. Inclusive pode soldar um novo fio direto na placa do alto falante sem aquela placa do controle de volume
Qual fio você utilizou um cabo usb comum? a qualidade mudou muito?
Thanks a lot man, you are great :)
+İlhan Tanrıverdi you are welcome 😉👍
the metal on mines broken..NOOOOOOOOOOOOOOO
Metal'? the only metal thing there is the speaker... how did you manage to brake it? :O
@@snowkingcro i accidentaly stood on it, but i bended it back the right way now.
you are the best
+Dp Pie Full HD Thank you!
snowkingcro how to fix my broken USB on rzr kraken 7.1 chroma the USB is cut off.
+Dp Pie Full HD You will need a wiring diagram.
ok
Surely nobody actually did all this
could be so
Razer Kraken USB is actually trash, i have it and i use it for 3 months and its broken for no reason.
needa sodder gun then im gud mine been down for 2 years or so best headphones i ever had
I bought it for 162$ and it stopped working for less than 3 months
same with me, I have the Razer kraken pro v2 and the left speaker just stopped working after a month.
Razer Headphones are Garbage
The audio dial on the cord isnt working (I can just scroll it over and over! And the sound coming out of it is overall garbage because of it!)
If i can fix this easily
PLEASE DONT HESITATE TO TELL ME HOW!!!!!!!!
+EruptionBlade4565 i think that your dial broke off... Or the resistor died, so the signal that comes out is bad
Grobmotoriker wie du sollten die Finger von solchen Sachen lassen..... Das kann man Sich ja nicht ansehen.
Ich danke dir an deinen Kommentar, aber leider bin ich kein motoriker... Nur koch, aber das nächste mal werde ich mich verbessern! 👍😏
razer kraken 7.1 chroma
Or just buy New ones
Yeah give another $100 to razers shit product whick will break again right ?
Or repair them instead of waisting money 😂
my headphones keep cutting out for no reason and everything is fine.
Well if they keep cutting i wouldn't be so sure they are fine XDD
It didnt work since im not on a laptop, atleast i didnt dislike so be happy with that
great not the fixi was looking for and i also unscrewed everything and cant screw them back these headphones are trash
Easy ಥ‿ಥ
its easy lmao