That is a very good bottle Jack modification. Those types of jacks are called Toe jacks. They are used for “low-slung” lifting situations, especially forklifts. The side gussets are what gives the entire mechanical modification its strength. Keep up the good videos. Have A Productive Day! 🛠️🧰🗜️
Commonly known as a toe jack....used to lift lathes and mills for leveling in the workshop.... but probably needs to be a bit heavier in build for that...but a good idea.
I am deeply impressed! All that metal work in FlipFlops. Using the angelgrinder whitout guard, you can see the sparks flying on the naked toes, no gloves. Now welding, more, hotter sparks on the toes. Realy great. Unfortunably can't see the saftey glasses -- or the lack of them??
I made this month's ago without the welding because of a rotten refrigerator that was sitting on a slope, so I used the bottle jack to raise one corner to put wedges underneath..... Then, I used the same technique to pull up a small stump in the garden.... tied the top of the stump to an angled bar, then the bottom of the bar to the lift on the jack.... About 3 full lifts, the stump was out.... I had the bottle sitting high on bricks to give height leverage.... it worked....
Looked good right up to the point where you made those two side stiffeners. After you tacked them on, you should've gauged a bevel in all four contact points to have more strength especially since you ground the weld all the way flush with the flatbar. You ground off every bit of the weld off making those stiffeners useless ! All welders and fitters that have any experience know that !!
Clever and well done. However I wish creators would realize that people don’t need to actually watch the welding. You can just show that you’re going to weld then show it welded.
I hope DIY'ers don't use the angle grinder like he does. Just a slight mistake could cause a kickback or flying shattered disc fragments and even SERIOUS CUTS. Watch some accidents while on RUclips. Respect the sheer force and cutting efficiency of this tool against human flesh and bones. ABOVE ALL learn how to USE THE TOOL SAFELY and PPE.
I was running mine without guard and just touched the blade with my knuckle. Was nice that it cauterized my deep cut but that took nearly a month to heal
Nice..really nice! Thanks for posting. May God Bless
Good job...simple but effective
That is a very good bottle Jack modification. Those types of jacks are called Toe jacks. They are used for “low-slung” lifting situations, especially forklifts. The side gussets are what gives the entire mechanical modification its strength. Keep up the good videos. Have A Productive Day! 🛠️🧰🗜️
Sangat bagus Bro
Excelente trabajo 👍🏻👍🏻👍🏻. Saludos desde España 👏🏻👏🏻👏🏻
Ini baru ide bagus buat pintu yg mingsle broooo... Gak kepikiran blasssss😂😂😂😂😂
Un gran invento,muy útil ,aprovechable y muy bien hecho 😊
Perfect. You are a true craftsman😊
Thank you
I've used pry bars just for that, n they work just fine. Harbor Freight has them cheap.
Oh yeah, they also have those bottle jacks too! 😳
Very good idea, thank you
Very useful, more versatile uses for small jack
Nice job thanks
Wow welding and flip flops goodness
Ahunque con limitaciones el ingenio es imparable!!!
Ótima ideia bem funcional parabéns valeo é nós.
Boa ideia, gostei.
You really should be wearing steel toed flip flops.
Nice work.
Thank you
Like it man
Amazing 👍
Kreatif abies, bagaimana kalau di sebagian permukaan tumpuan beban di bikin ulir agak kasar, seperti ulir drat,biar tidak licin pada saat angkat beban
Terimakasih atas masukanya bang
@@whuidemu Terima kasih juga sudah berbagi ilmu kreatif dan inovatif nya,
Excelente accesorio
Commonly known as a toe jack....used to lift lathes and mills for leveling in the workshop.... but probably needs to be a bit heavier in build for that...but a good idea.
Supar maind 😊
I am deeply impressed! All that metal work in FlipFlops. Using the angelgrinder whitout guard, you can see the sparks flying on the naked toes, no gloves. Now welding, more, hotter sparks on the toes. Realy great. Unfortunably can't see the saftey glasses -- or the lack of them??
What a great idea, he should patent it, could make lots of money.
I made this month's ago without the welding because of a rotten refrigerator that was sitting on a slope, so I used the bottle jack to raise one corner to put wedges underneath.....
Then, I used the same technique to pull up a small stump in the garden.... tied the top of the stump to an angled bar, then the bottom of the bar to the lift on the jack.... About 3 full lifts, the stump was out.... I had the bottle sitting high on bricks to give height leverage.... it worked....
Never stand a jack on bricks. It will end up back falling into the mud you dopey liar
Excelente ❤
Excelente así cubre más el espacio y no daña el chasis
So useful❤❤
knap gedaan, ik heb het nagemaakt, heel handig, bedankt voor het goede idee!!
Good idea from mauritius
Bagus nih hasil karyanya, apa dijual?
Semangat yu wahyuuu,,,
Konco lawas iki
Lp0o😊0
ㅖ9@@agunggilang8631
@@agunggilang8631😅
Bagus.
wow you reinvented the toe jack
Bravo complimenti bel lavoro ciao
ZOʻR ISHLAPSIZ USTA🙋👍🇺🇿
Looked good right up to the point where you made those two side stiffeners. After you tacked them on, you should've gauged a bevel in all four contact points to have more strength especially since you ground the weld all the way flush with the flatbar. You ground off every bit of the weld off making those stiffeners useless ! All welders and fitters that have any experience know that !!
It's fine, with zero support on the toe it's not the weakest link
Mantap om
Terimakasih om semoga bermnafaat
일명 "발톱잭" 이라고 하는데 주강철로 만들어진 재품이 있습니다. 하지만 지금 만드신 "잭"은 무거운 물건을 들어 올리면 변형이 생깁니다...
Gostei do vídeo
Boa ideia parabéns.
Bonjour, moi, quand j'utilise du trichlo , d'autres diluants ou acétone ... , j'utilise des gants !
It's Called A toe jack and they have been on sale for Decades
Amazing
Mucha inteligencia animo
What rod are you using 11 or 13 🤔
Clever and well done. However I wish creators would realize that people don’t need to actually watch the welding. You can just show that you’re going to weld then show it welded.
Thankyou
A crowbar and a floor jack would work better
😢
A crowbar and wooden block works much faster
Whoopie
And I certainly wouldn't be using a sweatshirt as a long sleeve shirt I've seen too many accidents because of Shawty dressing when you're welding
Add a return spring inside the tube
Must be a very small forklift! HaHa
Quá hay …!!!!
Me gusto
Eine einfache Zahnstangenwinde tut es auch.
Claw jack on Alibaba.
❤
Why wouldn't you paint the parts separately for more complete coverage?
Узконаправленное приспособление. Диван поднять и колёса на электромашине ребёнка поменять.
А в общем для хенд мейд на колене хорошо.
I thought he was going to put a couple holes in the outer tube and a few more in the inside tube and have a jack stand.
Doesn't anybody use stringer beads anymore!?
not when you cant weld properly
Most probably doesn't even know what that means
10 pra ti
Yg di dongkrak enteng2,rugi klo buat kaya gitu
Ну если дверь поднять, и так, по мелочам, а остальное...Под вопросом😂
How to make a jack out of a jack
รีลาเยอะมากว๊ะ
I'll take 2 how much and fucking great idea!!!
I hope DIY'ers don't use the angle grinder like he does. Just a slight mistake could cause a kickback or flying shattered disc fragments and even SERIOUS CUTS. Watch some accidents while on RUclips. Respect the sheer force and cutting efficiency of this tool against human flesh and bones. ABOVE ALL learn how to USE THE TOOL SAFELY and PPE.
I was running mine without guard and just touched the blade with my knuckle. Was nice that it cauterized my deep cut but that took nearly a month to heal
Dudes welding in flip flops…..
it is still jack??? whats new
nothing new its call a toe jack ..... and click bait
When is the welder gonna show up
Buckshot from welding will make you dance wearing flip flops.
पंप में तेल कितना डाला वह नहीं दिखाई या
Kh de xo dien thoai
A grinder with no guard, bare hands ,this is not a real welder
Ha… yup unencumbered by “safety” protocols
Sin salvaguardar no entiendo no se cuidan
No gloves, short sleeves, flip flops, reckless use of the angle grinder. Safety was out the window.
Safety third
Only way to go
Relax Karen. He will be ok.
Yikes! Stick welding while wearing shower shoes and no gloves!
Brave soul, stick welding with bare hands and sandals… smh
Nice build but....can you leave out the annoying repetitive "music" ? It is very annoying and not necessary.
Concordo a música é tão irritante que, se perde até o tesão em assistir o vídeo
if you're impressed with this
then bubble wrap must really amaze you...such a waist of time
बोला
El problema de estos vídeos Q tardan muchos para el resultado no me gusta
It is a dam shame you don't talk and explain what you are doing
He probably doesn't speak English.
Se. Deve de adaptar para subir los carros ,,,,cuando cambias las llantas ponchadas
Sigo como Eraclio Garces
Seriously??? 🤦♂️🤦♂️🤦♂️🤦♂️
lolol click bait for ya
Co.dong.kich.ban.ko.xin.gia
What a great idea, he should patent it, could make lots of money.