@@logangary531 it was all I had maxpeeding rods the best ones they sold but two times of orderin them they come with blown shocks so I sent them back and got rev9 suspension and it road perfect it was able to go a lot more in the front it was touching rim just a little and back I didn’t use any springs just the shocks and it was hammered but matched the front it was ruff but if I ran the springs low as they would go in the back it road great but it wasn’t near low enough
You can take out the adjuster part on the back springs and it gives you a inch or two lower with still having coils and then just adjust the damper on the struts it worked great too but I went to static on mine before I sold it
Hey man! Car looks sick was just wondering if you ever solved your problem with the caliper clearance? Want these wheels they are great wheels for the track and cheap but I am planning on getting type s calipers and want to know if they would clear.
I have a set of rpf1s on my Fa5, +22 in the front and +35 in the rear. 225 size tire. I have the front pretty flush running 1.2 degrees of camber, but I had to roll the fenders basically as much as possible, and then use a dremel to cut away at the front corner where you cant roll it flat. I will only rub if I go over a giant bump at a high speed. Rears about 3 degrees of camber (Might be a little less), had to roll fenders and shave the tab where the rear bumper clips on. No rub at all with these specs in the rear.
Hey man. Not sure if what I have to say will help you, but here goes. I have the Wilwood Superlite 6R BBK on my 8th Gen with 17x8+35 RPF1s (bubble face as opposed to the flat face you’ve got), and they cleared without any problems. I’d be inclined to say they’d fit your BBK too, but I’d take measurements first.
From what I’ve seen on some websites that sell the BBK, the 17x8 +35 RPF1’s do clear without spacers. But personally I don’t like the way the bubble face looks.
RPFJuans are so overrated and so overused here in the US 😂. It’s common rice wheels for cheap dudes who can’t afford real wheels. But good luck trying to pick up little boys at Honda meets lol
Damn, it must depend on the thickness of the spacer that you run behind the TL rotor, or if you run the s2k rotors then you’d probably need a small spacer still.
I just static dropped my daily 8th gen on 17s today it rides perfect for so low very happy with the outcome
What's your setup on the 8th gen? Thinking of getting wheels and tires for mine
@@logangary531 it was all I had maxpeeding rods the best ones they sold but two times of orderin them they come with blown shocks so I sent them back and got rev9 suspension and it road perfect it was able to go a lot more in the front it was touching rim just a little and back I didn’t use any springs just the shocks and it was hammered but matched the front it was ruff but if I ran the springs low as they would go in the back it road great but it wasn’t near low enough
You can take out the adjuster part on the back springs and it gives you a inch or two lower with still having coils and then just adjust the damper on the struts it worked great too but I went to static on mine before I sold it
What you can do is get the New FD2 Front Fenders they also make them for the USDM as well.
Not sure that I've seen or heard of what you're talking about. They make FD2 fenders that fit with the USDM front end?
Nice setup! I'm running 17x9 +43 5zigens on mine. it barely clears my coilovers with 245/45/17 RT660s.
No way me too but with toyo r1rs
Hey man! Car looks sick was just wondering if you ever solved your problem with the caliper clearance? Want these wheels they are great wheels for the track and cheap but I am planning on getting type s calipers and want to know if they would clear.
I have a set of rpf1s on my Fa5, +22 in the front and +35 in the rear. 225 size tire. I have the front pretty flush running 1.2 degrees of camber, but I had to roll the fenders basically as much as possible, and then use a dremel to cut away at the front corner where you cant roll it flat. I will only rub if I go over a giant bump at a high speed. Rears about 3 degrees of camber (Might be a little less), had to roll fenders and shave the tab where the rear bumper clips on. No rub at all with these specs in the rear.
Yeah the rears are gonna clear once I roll it just a little more, but the fronts are gonna be a mission.
Nice setup man! Just picked up an 8th gen si, same color as yours. Where did you get the front lip?
I think they will clear og ce28 17x9 35 offset
I want this rims so bad on my 9th gen these are to sick nice choice 🔥🔥
Hey man. Not sure if what I have to say will help you, but here goes. I have the Wilwood Superlite 6R BBK on my 8th Gen with 17x8+35 RPF1s (bubble face as opposed to the flat face you’ve got), and they cleared without any problems. I’d be inclined to say they’d fit your BBK too, but I’d take measurements first.
From what I’ve seen on some websites that sell the BBK, the 17x8 +35 RPF1’s do clear without spacers. But personally I don’t like the way the bubble face looks.
Get some evo 10 gsr wheels!!! Same look but clears perfectly
Hey man what were the old wheel and tire setup you had before you put the rpf1s on?
Yoo bro what front lights are tho and where did you get them ??
what trim is that on your pillars?? forged carbon? ... POST MORE FA5 CONTENT!!!!!
Forged carbon wrap I did myself over a year ago to cover up the fading trim, still holding up nice.
Where did you pick the headlights?
Hey man i know this video is old but are you running camber arms?
In this video no, but you’re gonna need camber arms if you want this exact setup not to rub.
Are the wheels 73mm bore? I wanna run the same center caps just not sure about if they would fit since my other Honda center caps didnt fit.
Yeah these are 73mm hub bore
What center caps did u use bro?
I used some silver Honda center caps I got on eBay I think any 69mm center cap works
Hey what headlights are those ?
Lightcreationz retrofits
Did it rub on the caliper cause the calipers are bigger compared to stock calipers ?
Yes brembos are significantly bigger than the stock calipers. Almost any wheel will size and offset will fit the stock calipers.
RPFJuans are so overrated and so overused here in the US 😂.
It’s common rice wheels for cheap dudes who can’t afford real wheels. But good luck trying to pick up little boys at Honda meets lol
What would you consider real wheels? Like rays ?
that's a first, your definitely neurodivergentcalling enkeis fake wheels.
I had 17x9+22 and they didn't clear 🥲
Damn, it must depend on the thickness of the spacer that you run behind the TL rotor, or if you run the s2k rotors then you’d probably need a small spacer still.
@@npvfa5 i don't have any spacers behind my rotor lol, just running s2k rotors and the tl brembo