Rong Fu RF30 Round Column Stabilization Part 1

Description
Here to have some fun and to make new friends & to learn & pass on New Info from the RUclips Family. Feel Free to Subscribe & Press that Little Bell. Thanks
• Rong Fu RF30 Round Co...

[@EverettsWorkshop]

I like your cold chisel skills, that was a pretty intricate chisel hit, lol!

[@TedRoza]

G'day Everett, wasn't sure if I would have to use the 14 lb hammer or not 😆 🤣 😂

[@pgs8597]

G'day Ted. Good start, that's a lot of work cutting through 25mm steel, good thing you have the machinery. Keep up the great work, cheers. Peter

[@TedRoza]

Hi Peter Thanks for your comments, yep lots of work, but getting there 🐌 🐌 🐌
😆 😆 😆

[@Bartolobot]

lovely manicure your hands are so clean. it's like your designing garments and that's your sewing machine. bravo

[@TedRoza]

Must be all the Tellus 68 Hydrolic oil I use .. lol, because this isn't an old Singer Sewing Machine lol

[@TheKnacklersWorkshop]

Hello Ted,
Good to see a new video. Nicely done and I especially like the cold chisel work - lol. See you in part 2.
Cheers.
Paul,,

[@TedRoza]

Thanks Paul, always a pleasure hearing from you

[@ianbertenshaw4350]

Great video ! I wonder how many of those RF30 mills have been sold - must be millions !

[@TedRoza]

Hi Ian .. under the Names of Rong Fu ... Grizzly etc, uncountable . For some reason they just keep Hanging On ... 😆

[@1crazypj]

Don't know how long they have been selling them, at least since early 1980's so your probably right.
I've had mine about 15 years

[@agentcovert]

Epoxy granite plus steel rods like rebar back filled in the empty castings will add mass needed for vibration mitigation as well as limiting any flex..epoxy granite is simply 80% to 90% mix of dry sand and dry pea gravel with the rest of it being standard epoxy such as boat fiberglass resin etc..even without rods will add so much mass when the base and column is filled with epoxy granite it will allow for much bigger depths of cut as it just soaks up any vibration stopping chatter..

[@MattysWorkshop]

Gday Ted, off to a good start there mate, looking forward to seeing the next instalment, cheers

[@TedRoza]

Thanks Matty, Greatly Appreciated, hope it's as good as yours

[@GlennNowOnYouTube]

Good job so far. I will be using your ideas on my mill. Most likely making a video of it on my channel. Thanks for the post and idea's. GlennNow on RUclips.

[@TedRoza]

Thanks for your comment, greatly appreciated. Have fun with your build

[@swanvalleymachineshop]

👍

[@TedRoza]

Thanks Max .. Thumbs 👍 👍 is Good lol

[@maxfarr4142]

Nice. Keen to see it come together.

[@TedRoza]

Thanks Max .. greatly Appreciated

[@ianmoone2359]

Masterfully done Ted.
Will be watching with interest to see it all come together.
This mill will no doubt end up being right foo rather than wrong foo once your through with it. 😜😂👍👍👍🇦🇺

[@TedRoza]

Thanks Ian .. Maybe if I get enough mods, it will think It's a Bridgeport.. 😆 😆

[@ianmoone2359]

@@TedRoza Give me a couple weeks and we might be able to compare hopefully.
I still would love to come and see your Hafco lathe in person at some point when you have an hour free if it’s OK?

[@TedRoza]

@@ianmoone2359 NP we canwork it out