Looks like a SUPER easy repair! I have an 01 mustang, a fellow u tuber showed me how to clean up the original non-working blower motor and oil it and brought it back to life. 4 years now still working
Have you had a "clunk" when you reverse or start to take off that sounds like its from the front right tire yet? Everytime you go from reverse to drive and then it feels like somethings (tie rod) loose and THUMPS back into place! It does this if you take slow, hard turns also and when you straighten out.....THUMP! Im told its a tie rod but have not got to it yet! Oh, amd dont forget the notorious oil pressure sensor that you have to jack tne frame up to get to it lol. I have bought GM products (few Fords and a dodge) all my life but im DONE! TOYOTA Tacoma or Nissan Frontier im told by many is the quality, longevity and access to repairs that we have been missing so thats my next direction! I dont care where its made, I just want a dependable vehicle that I CAN maintain lol.
I hear ya. This one had the tie rod ends replaced before I bought it. I haven't noticed that. I did have a clunk which felt like it was coming from the rear but it was the drivers side engine mount. This Chevy trucks are great, but the quality and reliability is just terrible. It's a shame.
If Toyota made something like a Suburban (seats 9 and still has large rear cargo) I would buy it. And I just did the oil pressure sensor, sits at the back of the intake manifold, a tight squeeze but done in 1 hour, no lifting the frame or whatever you mention.
Looks like a SUPER easy repair! I have an 01 mustang, a fellow u tuber showed me how to clean up the original non-working blower motor and oil it and brought it back to life. 4 years now still working
Yes this was one of the few times I didn’t run into a problem lol.
Do yall know what size screws hold that cover underneath the dash?
Hey man where in TN! You shoulda stopped by - Thats where I am
Sevierville, Pigeon Forge, Gatlinburg
If we go again, I will let you know!
@@nowherefastgarage I live exactly 2 hours away - chattanooga area
What’s that little part on the blower motor you were talking about?? Mine has the same thing just wanted to make sure it was ok not adding it
I'm not sure, but probably some kind of venting device.
Thank you for the video!! Greatly appreciated!
You've had to do alot to this Suburban.
Tell me about it! I love it, but the GM quality is just horrible.
dude just puts the mf right in, im over here struggling, cant even put the factory one back in wth
I guess I got lucky on this job? I'm usually struggling.
Do these have cabin air filters?
I don't think so?
I’m going through this now
What I really wanted to know was how it was removed
Just twist it. Watch the video!
Have you had a "clunk" when you reverse or start to take off that sounds like its from the front right tire yet? Everytime you go from reverse to drive and then it feels like somethings (tie rod) loose and THUMPS back into place! It does this if you take slow, hard turns also and when you straighten out.....THUMP! Im told its a tie rod but have not got to it yet! Oh, amd dont forget the notorious oil pressure sensor that you have to jack tne frame up to get to it lol. I have bought GM products (few Fords and a dodge) all my life but im DONE! TOYOTA Tacoma or Nissan Frontier im told by many is the quality, longevity and access to repairs that we have been missing so thats my next direction! I dont care where its made, I just want a dependable vehicle that I CAN maintain lol.
I hear ya. This one had the tie rod ends replaced before I bought it. I haven't noticed that. I did have a clunk which felt like it was coming from the rear but it was the drivers side engine mount. This Chevy trucks are great, but the quality and reliability is just terrible. It's a shame.
If Toyota made something like a Suburban (seats 9 and still has large rear cargo) I would buy it.
And I just did the oil pressure sensor, sits at the back of the intake manifold, a tight squeeze but done in 1 hour, no lifting the frame or whatever you mention.
Dumb video didn't show how do the job
What else do you need to see?
useless video 💀
Sorry it wasn't helpful.