How To Replace Window Regulator 02-07 Jeep Liberty
HTML-код
- Опубликовано: 17 окт 2024
- Shop for New Auto Parts at 1AAuto.com 1aau.to/c/16/bF...
In this video, 1A Auto shows you how to repair, install, fix, change or replace a slow, stuck, cracked or damaged window regulator. This video is applicable to the Jeep Liberty, years 02, 03, 04, 05, and 06.
🔧 List of tools used:
• Flat Blade Screwdriver 1aau.to/oacw/1A...
• Phillips Head Screwdriver 1aau.to/oacw/1A...
• 10mm Socket 1aau.to/oSo/1AX...
• Needle nose pliers 1aau.to/okA/1AX...
• Needle nose pliers 1aau.to/okA/1AX...
• Ratchet 1aau.to/oaee/1A...
• 11/64 Inch Drill Bit 1aau.to/oac/1AX...
• Drill
• Painter's Tape
• Putty Knife 1aau.to/oec/1AX...
For More Info visit us at 1aau.to/h/a6B/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto
√ *Do it Yourself*
√ *Save Money*
I realize it's kinda off topic but do anybody know of a good site to watch newly released tv shows online?
You saved me lots of money! Thanks! (The replacement piece I bought did not have a small bolt to replace the rivet, so if anyone does do this, make sure you either buy a kit with it, or go to the hardware store and buy one).
Thanks for this video - I just used it again to replace my rear left Jeep Liberty left side rear and after a couple of false steps at the beginning I used the video to get back on track.
I have replaced rear window mechanisms 3 times on my 02 Liberty. Getting pretty good at
the routine. The video helps. However, on two of the three the stud would not stay in the clip. I ended up twisting the stud out of the plastic (on one) and through bolting (1/4-20). The other one, watching and waiting to see what happens. The window seems to be under a great deal of stress when following the curve of the new mechanism. Not sure if the curve is correct ? I see several other posts describing the same problem. Be nice if 1a auto would address this problem.
Great video! Thanks for the great detail. I knocked of the complete R & R in 45 minutes. Many Thanks!
Apparently the Jeep Liberty is infamous for failing window regulators. Both rear windows on mine started to slide down and wedges weren't working well. Your video helped me to access the innards (like that word?) And hook a bungy cord to bottom of window and door frame as a temp fix. Thanks!!
Thanks for watching. Have a great day! 1aauto.com 888-844-3393
Wow, thats so much better than just rolling them up and down
I used info from this and a couple others to perform a successful swap on a 2004 grand cherokee. Thank You!! It was easy once I went thru the videos and got the general idea.
Great video! I ordered the part and have no doubt I will be able to do it! Not as quick as you though.
thanks for video, just got my door regulator kit in mail from you guys and fixing to jump all over this....
I followed this step by step and it was really helpful but the problem I have is the rear window will only go down but when I try to go up it just falls so my question is do you think I just need to replace the window clip or what else could it be because the motor works fine to me
Ok, even tho nobody's answered this question in over 2 yrs. I'd love to know the answer !
So if anybody comes across this post -and knows... Lemme know somthin' -will ya? TIA
I have a 2002 liberty. The glass keeps popping out of the clip. I took it apart and I had to bend the post on the glass and it snapped right In. Lasted 2 weeks and now it popped out. Not sure if the post that's attached ti the glass is bad or if the rebuilt kit would work. Any suggestions would be great. Right rear door
+Joseph Vlock Thanks for watching! At this point I would recommend that you look into replacing the window regulator assembly. We do not have the repair kit for this vehicle anymore, but we do have a selection of regulators. Just visit www.1aauto.com, enter your year, make and model, and select the category "window regulator!" 1aauto.com
Are the kits still available? When I follow the links and go on your web site they are not there. Thank you for posting these videos they are very helpful.
+Lou Steger Hi, Lou! Thanks for watching, but unfortunately we discontinued that repair kit a couple years ago! Sorry we couldn't help. 1aauto.com
Thanks for the reply. Sucks because both rear regulators on my nephews Liberty broke :(
Thanks for the Video! I have the same problem with daughter's Liberty. Very helpful!
Wes Hopkins Thanks for watching Wes. We carry the repair part shown in this video on our website. Here's a link to it, if anyone watching would like to take a look at it. Have a great day. www.1aauto.com/jeep-liberty-window-regulator-repair-kit/i/1abmx00093?RUclips&CTA%20Comment&ATony
Thanks again! You guys are awesome!
I'm looking for help. I have a 2003 Jeep Liberty and the word Glass appears on the dashboard, the rear window is close how can I fix it? Thank you
Thanks for the video! Helped out greatly.
How do I know if I need the Rear Window Regulator Repair Kit?
I can hear the bracket moving up and down inside the door, but the glass has fallen out of the bracket and off the track.
8:06 The glass won't stay on that blackpiece in my door.
Does this sound like something that can be fixed without purchasing a new regulator kit?
Also, do you guys sell that black adhesive to seal the water shield back on the door frame?
I'm just afraid that if I start this project, I won't be able to put everything back!
Thanks.
You may want to remove the door panel to see if the regulator is broke, or if the glass somehow broke free from the window regulator. We currently do not sell the black adhesive for the water shield.
What is the name of the part that is attached to the actual window? The piece that he popped in into the new window guide at the end.
1a auto is great. Fast shipping. Good parts. Thanks.
+G W Thank you for your order. If you would like to leave us a review on Google it would be greatly appreciated. Here is a link to our reviews section. Have a great day! goo.gl/i5JFNY
I have a very difficult time clipping the window into the window clip .. it just doesn’t stay clipped in & keeps falling down!! What am I doing wrong??
Could someone please advise where i can find a unit as indicated 5:15 in the video? I have a liberty 2002 model and the plastic design has failed. I like to replace the unit without buying an entire regulator unit...
So I pulled out both clips and I still can't get the window to pull up? What am I doing wrong?
Worked like a charm...thank you!!!
+Dan Kuennen We're glad the video helped you out. Thanks for watching. 1aauto.com 866-403-3393
I have an 06 Jeep Liberty V6 3.7L. The temperature gauge on the dash has been reading as overheating. There is no white smoke and no bubbling from the coolant reservoir. I started noticing problems when the heater stopped working and then about a week later, the temp gauge starting rising. The car was then sucking about a gallon of 50/50 per week. I noticed a leak from the radiator, so I have replaced the radiator, thermostat, water pump, and the sensor for the temperature gauge with all brand-new factory parts. The vehicle temperature gauge still shows as overheating and it will go down when I turn on the heater. The fan works fine. A/C works fine. Heater works fine. The rubber hoses running to and from the radiator both get warm and it feels like coolant is traveling through. Some people told me it is probably a leaky or cracked head gasket, but the oil looks fine, there is no white smoke, and there is no bubbling from the reservoir.
Do you think it could be a head gasket? Is it maybe just a shorted wire causing the gauge to read hot? Is the vehicle just possessed? Any ideas are appreciated. Thanks.
You may want to check the coolant level when the vehicle is cold to see if there's plenty in there. Check the fuses and relays to see if they're okay.Also the radiator fan too, to see if the fan motor may be bad. To check the fan let the vehicle get up-to-temperature, and see if the radiator fan kicks off and on, it should also kick on if you have AC and turn it on. Here's a link to the 06 Jeep Liberty parts section on our website. Shipping is free on all orders in the lower 48 states. Hope this helps you out. www.1aauto.com/2006-jeep-liberty-parts/y-mo/2006-876?VideoReply&VideoReply&ATony
Can you post a video on how to install the actual window of o 2007 liberty? There are literally no videos on the internet of someone putting a window into the door and it's really annoying because all I see are dozens of videos about the regulator
+Shaunn Marshall Thank you for watching. We will forward this to our Studio in hopes of a video being produced in the future. 1aauto.com
the part you took out and rebuilt is not the same part as you reinstalled WHAT GIVES??????
excellent observation mate!!
Wholly Sheeeeit! "Busted, Disgusted and cant be Tr-*s-*d" (lol) Ah, I'm not gonna say it.
Ya know why? CUZ THESE GUYS ROCK! I mean, all the video's they make and put out for us?
Someone is bound to mix up a video clip when they edit them together for the final version -ya know? Its not the end of the world... It wasn't THAT obvious... And its not like they jerry-rigged a Ford regulator into this Jeep... (right?)
So, hey... Let all yell out a "hell yea" for A-1 Auto
At frame timestamp 6:48 it shows the tech installing a different regulator than the one he just repaired!
Why?
Ciuld it be that he snapped the poly cable guide tube while he was savagely rupping the original reg. out?
I jave found it best to do this removal in a warmer environment so the ppe is more pluanle and forgiving of tight radius bends. Also theregulator/motor assembly as a whole, is extracted more easily by spinning the unit in a CCW rotation as you first guide the motor subassembly followed by the regulator assembly which will be trailing right behind the motor. This technique increases the radius forced on the ppe tubing. Thereby you reduce the likelihood of snapping the tube at the stess riser point where it connects to the goosneck ppe piece that is rivet/clipped to the metal guide rail.
Thanks for sharing theoney saving alternative to replacing the entire component.
Be Safe
good work on it #holddown
Thansk very very much
A few observations: You missed routing and re-clipping of the free tube [the bit connected to the motor bracket but not the actual regulator, also called the 'runout tube'].
I'd recommend lubing the track and...
... finally it's always good to test the works before buttoning it all up.
+jbelicka The window regulators that we carry come pre-greased. Here is a link to the replacement window regulator for on this website for your vehicle. www.1aauto.com/1A/WindowRegulators/Jeep/Liberty/1ABMX00093?RUclips&CTA+Comment&Tv2Uq2oiFBA
Do you sell the repair clip shown in this video?
+Wayne Moureau Thanks for checking us out! We do not currently carry these clips. 1aauto.com
1A Auto Parts
I did purchase the need part for my vehicle. Thanks
awesome!!! thanks!!!
Excellent video. But, I need one for a 2007 Jeep Liberty-rear window. I guess I'll keep looking :(
Thank you for watching. Unfortunately we do not have a video for your application. We will keep this repair in mind for future videos.
888-844-3393
Hi Guys, Love your videos. I need to buy one of these rear window regulator repair kits but can't seem to locate the part on your site. Can you help me?
+David McCubben Hi, We now carry the complete window regulator assembly. Here is a link to them on our website. Hope this helps you out goo.gl/PZyijg
Just did an 05 liberty rear window. 45 minutes working slowly for the whole job. Easy
cant find it on your site , whats the part number?
+buffalostate1 We currently do not carry a repair kit. Here's a link to the replacement window regulators that we carry for your Jeep Liberty. Hope this helps you out. goo.gl/kokpV8
You didn’t even put the same regulator back in it ! Why would you change the regulator and not pit the repaired regulator back in ,,,
for real? How'd I miss that?!?
I did this repair, but now the window won't stay in the bracket. The little clip won't hold the stud in the bracket, and every time you close the door, the window falls all the way down. Such a stupid design from Chrysler. Why wouldn't they have the pin go through the stud and not just around it.
Matthew Walker Got it figured out. The opening for the stud was really tight on the one side. So while the stud was snapping into the clip, it wasn't all the way in the bracket itself. On the drivers side back it went in like it should, but on the passenger side I had to use a c-clamp to get the stud to come into the bracket. Yes, both rear windows on mine had the regulator problem.
muchas gracias amigo i save 100 dollar
Hey guys, just wanted to make sure I am purchasing the correct parts. I need to replace the driver side, back seat side. If I order from the link below, should I have everything I need (tools aside) for the repair?
Thank you
www.1aauto.com/jeep-liberty-window-regulator-driver-side-rear/i/1awrg02382?f=806309&y=2006
+Sam Thoen Hi Sam, if you give our customer service a call at 866-403-3393 they should be able to help you
GRRRRR UM SHEWWWW UMMMMMM DAMN UMMMMMMMMMM GRRRRRRRRRRRRR LOL