He mentions the 3mph kick in the first minute. I don't think this is your problem from what I can see in the video, but you can wire the batteries wrong to where the red power LED comes on but the motor won't turn, and you won't hear the click from the throttle. The red/black wires from the white plastic connector should go to BOTH batteries - black to one battery, red to the other. Same with the reset switch - it gets a connection from both batteries. This connects the batteries in series, supplying the 24v needed to turn the motor and activate the throttle relay.
If the charger stays green, it is actually telling you to replace the batteries. My charger was doing the exact same thing by staying green but when i did a battery replacement, it went back to red. So if the charger stays green, replace batteries
*the motor sezes if you leave it awhile*wd40 and Bang on it and it comes free* *And they crammed everything in a small space when i took it out and spread IT OUT IT WORKED*** *CATER*
Just an FYI mine was doing the same thing and it has a safety feature you have to get it going up to 3 miles an hour with your foot then the motor will kick in
Hey dude.. I disconnected the brake line and reconnected it. It began taking a charge. I triggered the brake line while charging and charger displayed “Charged OK”.. manually pushed it around for a bit and recommenced charging but left untouched and it’s continually receiving a charge now. So I think the problem lies in the brake line staying locked on. But is up and running now.. Thanks for your video! Hope u get it up and running.
Have the same problem with a Dyna Craft Serge City scooter. 24 volt motors fine, chargers fine. put new circuit breaker in it. controller is clicking, front brake switch is clicking. Please help!
I’ve got the ‘PowerCore E100’ and mine won’t work, it’s a push and go and I’m doing that.. my charger shows that it’s charged, it turns on, everything. It. Won’t. Go. Someone help me!
Any idea when I have it on table and spin tire with throttle applied tire spins no problem but when daughter tries to ride it it does not turn on any ideas???
The kanooder valves at my local Radio Shack and Circuit City were all sold out. Fixing these are hard because is has a base-plate of prefabulated aluminite, surmounted by a malleable logarithmic casing in such a way that the two main spurving bearings were in a direct line with the pentametric fan. If you have any other suggestions, I'm all ears! 🙂
I have a e300 new batteries fully charge. the motor work fine but as soon as I get on it can't go, or go very slowly and stop, I am not heavy 141pounds. could it be the motor damage in someway?
Unfortunately no, this project was abandoned as we eventually got a hoverboard, and EcoReco M5, and a Ninebot. I still love these little Razor electric scooters though!
My one turns on and goes but it's not as fast as it was now it struggles but when you walk with it it goes fast but back tire is little flat so that's probably why anyone have any ideas let me know
Wow I didn't even know I had to push the scooter 😂😂😂😂 I've been having this damn thing charging for weeks
deairreo hill lol
Lol I did the same shit
He mentions the 3mph kick in the first minute. I don't think this is your problem from what I can see in the video, but you can wire the batteries wrong to where the red power LED comes on but the motor won't turn, and you won't hear the click from the throttle. The red/black wires from the white plastic connector should go to BOTH batteries - black to one battery, red to the other. Same with the reset switch - it gets a connection from both batteries. This connects the batteries in series, supplying the 24v needed to turn the motor and activate the throttle relay.
If the charger stays green, it is actually telling you to replace the batteries. My charger was doing the exact same thing by staying green but when i did a battery replacement, it went back to red. So if the charger stays green, replace batteries
I never knew this. Thank you for sharing!!
*the motor sezes if you leave it awhile*wd40 and Bang on it and it comes free* *And they crammed everything in a small space when i took it out and spread IT OUT IT WORKED*** *CATER*
Thank you for sharing! This is good to know.
I had one from 7 years ago. Thought it was broke until I read about 3mp kick in speed
Just an FYI mine was doing the same thing and it has a safety feature you have to get it going up to 3 miles an hour with your foot then the motor will kick in
Thank you SO much! I bought this thing used, and I didn't know that. Worked like a champ!
Hey dude.. I disconnected the brake line and reconnected it. It began taking a charge. I triggered the brake line while charging and charger displayed “Charged OK”.. manually pushed it around for a bit and recommenced charging but left untouched and it’s continually receiving a charge now.
So I think the problem lies in the brake line staying locked on. But is up and running now..
Thanks for your video! Hope u get it up and running.
What color was the wire that you just connected for the brake line
Thanks. ..great video. ..you gave me the ideas I need
Thank you
did u figure it out? im having same exact issue
what did u do after this haha
You need to turn the throttle and then spin the wheel to get it to go
Spin which wheel and what direction
@@lonestranger5161try both directions🤨
you have to push the sciiter ti gtt it going. its a safety feature.
Farhod Azarbaydjani I did that and it did not work
sorry to hear that.
You don't have to with the E300, not sure about the 100. You don't have to push it or be on it at all.
Push the what????
@@itswiddow5039 some say you have to push first before it well run...but some say you actually don't have to
What happened with those baby dolls on the floor?😮😢
LOL, what DIDN'T happen to them!? HAHAHA they've been through a lot!
Thanks for the laugh.
Give it a little bit push
Yeah for me that reset button has no resistance as well
These scooters work when they are already 2 miles away otherwise they do not work
when you when u disconnected the brake line switch what color was the brake line switch wire that you disconnected ?
Don't wanna admit it's yours! Need to wire in a mp3 player that plays WHITE n nerdy. I'm looking cuz I'm fixing one for a buddy too.
Need new battery also. After a few years they cant hold charge
Any help mine has the same problem
Necesita ayuda para mí patinete , donde encuentro las mismas baterías para cambiarlas
Have the same problem with a Dyna Craft Serge City scooter. 24 volt motors fine, chargers fine. put new circuit breaker in it. controller is clicking, front brake switch is clicking. Please help!
Kevin Taylor same problem different scooter
I’ve got the ‘PowerCore E100’ and mine won’t work, it’s a push and go and I’m doing that.. my charger shows that it’s charged, it turns on, everything. It. Won’t. Go. Someone help me!
Any idea when I have it on table and spin tire with throttle applied tire spins no problem but when daughter tries to ride it it does not turn on any ideas???
Joe Medina Advocare propbably a faulty wire....goes faulty when you turn it upright...if not the motor will be half dead
should of checked the continuity of those cables too
Its probably a bad kanooder valve. Pick one up at Radio Shack
The kanooder valves at my local Radio Shack and Circuit City were all sold out.
Fixing these are hard because is has a base-plate of prefabulated aluminite, surmounted by a malleable logarithmic casing in such a way that the two main spurving bearings were in a direct line with the pentametric fan.
If you have any other suggestions, I'm all ears! 🙂
I have a e300 new batteries fully charge. the motor work fine but as soon as I get on it can't go, or go very slowly and stop, I am not heavy 141pounds. could it be the motor damage in someway?
From what I know the max weight for the razor electrics is 120lbs. Might be different for the e300 tho.
Tilt your camera up. Half the vdeo is your voice and a blank floor.
Well, I just wasted 7 mins of my life.
TxMa'am why watch it clever guy
7 minutes isn't that much time, you were entertained watching the video
That's why there is a fast forward option! I wasted 1 minute
😊
No shit
How many kilometres can it travel?
Razor claims around 10 miles while I think is a bit optimistic.
Move it first a race it will work
U got to kick the scooter to engage the motor
Hours of charging?
Razor suggests I hours to fully charge the batteries.
How do u get it to charge my charger stays green
same
Same
I have same problem ! Did you ever figure the problem out ?
Same
You left it switched on, the battery needs to be replaced
So there is no follow up video or update on the issue?
Unfortunately no, this project was abandoned as we eventually got a hoverboard, and EcoReco M5, and a Ninebot. I still love these little Razor electric scooters though!
That thing you called a "bcm" is actually an ESC.... (I might be wrong)
Any idea of e300s mileage?
Unfortunately, no.
I hear the click but it will not run , I think battery is dead or one of them ; but I hope not..
AA Killer you have to push it to make the motor go
My e100 dont look anything this
it is not working properly because you had it on when you were not riding it that is why
That was dumb
some people just enjoy embarrassing themselves in public ;-(
7 mins wasted...
Thanks for sharing. Same problem here. Hope you were able to fix
get a $5 multimeter....obviously more diagnosis is needed... no way around that.
It's thottle cable and electrical bicycle controller it a $30 fix
Craig Spindles really ? I just paid $20 for one and it has this same issue
is this also for e175
My one turns on and goes but it's not as fast as it was now it struggles but when you walk with it it goes fast but back tire is little flat so that's probably why anyone have any ideas let me know
The motor probably doesn't work I have the same problen
Mine turns on but the charger always shows green. Tested the charger and was good so heard it was batteries are bad
What a waste of my time this guy hasn’t got a scooby doo
Same issue
Stop video taping the floor