Hydro Gear ZT2800, ZT3100, ZT3400 Oil Change and Air Bleed
HTML-код
- Опубликовано: 19 апр 2023
- My Husqvarna MZ54 lawn mower hit 100 hours and needed the first hydro oil change. The service manual for the ZT2800/3100/3400 is available online. These are also used on Bad Boy Mowers and probably many more.
The tool and material list I used is here:
3/8 Socket and ratchet
11/16 Open End Wrench
5 quarts 20W-50
2 HydroGear filters Part Number 52114
Drain Pan and oil funnel
Please don't forget to purge the air out by pulling the bypass valve open and rocking the control arms forward and backward. 
Хобби
![Skilla Baby - Misfit (Feat. Polo G) [Official Video]](http://i.ytimg.com/vi/IjsylSnNMyw/mqdefault.jpg)
Thanks for the video, changed hydro oil out yesterday and it went pretty easy.
For anyone that has a filter that their filter wrench wont fit, use a leather belt. put it on the filter the opposite way you would normally wear the belt to remove the filter. Trust me it works
I saw a video somewhere of a hydro gear tech doing this. He drained it by taking off filters. He refilled through the vents with a 11/16 fitting with a small hose fitting coming off it with a length of tygon tuning coming down. The tube went to a simple hand plungle pump that threadeded on top of his oil container. he pumped till full, reinstalled vent plug, made sure reseervoir was at low cool mark, then purged. I'm going to try to find that fill fitting and pump.
Best video I have found! Currently can’t get those 11/16 bolts off. What a pain
Thank you! Good luck, there might be a slot for you to access them from above them. The left one was harder than the right one for me.
Great video
Great video.
Thanks alot of good information.
Think I'm going to pay someone to do this.
Thanks
I have to do the first hydro service on my Exmark Quest S 50",. Their manual doesn't show where the vent plug is. Not even certain what model the transaxle is. I think it's a 2200. Thanks for this.
I found a spot of something under my sealed hydro on my Ariens Edge. It was clear, thick and sticky......it definitely didn't look like 20w50 motor oil. Do you happen to know if they use a different type of oil in the non serviceable ones?
Hello, sorry I do not.
You said 100hrs. How many years has it been? I have a bad boy Maveric same Kawasaki, but the ZT3200 hydro gears. I'm beginning my 3rd year and mine has a tick over 40 hours. I may do mine before the 75-100hrs that it calls for just due to time.
We mow about 6 acres every couple weeks. This was the start of year 3, and we were probably at 80 hours.
@jimknowlton342
Ok cool thanks for the heads up. I only have 5 acres. I would say about 2 of them, maybe a little over 2 get mowed. I'm very particular about maintaining this thing. So I think by June I'm swapping out the fluid and filters..... I'm a heavy dude, my yard has hills, and I've used it to grade my 75yrd gravel driveway with one of those dr power grader, which has unearthed some boulders. It's almost brought the mower to a stop so my fluid is probably over due. Thanks again.
HydroGear told me to only use full synthetic high zinc oil. I don't know if that is what you used.
I don't know either. A check of their 2011 service manual shows no hits for zinc or synthetic. It's possible that recommendation has been made since then. Thanks for sharing.
Hydro Gear should sell you the oil they recommend - I would think.
What model year is your rideon
I bought it in 2021
Can you use any oil filter
Good question, I'm not sure I can answer that properly.
I love you
I'm blushing
@@jimknowlton342 I'm nauseous!🤔
How much oil did it take
Took very close to the recommended amount, can’t recall what it was, maybe a quart each or something? Can’t recall the exact amount.
The way I see it:
1) loosen up the cap of the reservoir
2) Take the bold off
3) take the filter off to drain
4) Bleed
My question is this:
Why do we have to take the bolt off if the filling will be from the reservoir?
Hope someone can help me on this!!!
Good question, maybe it allows air out or something?
By leaving the bolts out, you will know when each transaxle is full and also allows the transaxles to vent air (like what the author said) while filling according to the manual. You are supposed to put the plugs in when you see fluid running out of the holes. After that, continue filling the reservoir with oil until it reaches the FULL COLD line. After this, you start the mower and proceed with the "purging" procedure.
Great video