Wow, how easy this is. You just need about 1000 dollars of equipment including compressor and grinder and about two hours of work for one headlight plus assembly. Love it
@@2winis2doit5 bro what are you on. lol you clearly never worked on cars before, if you do then you should know how easy it is to remove the headlight and how common it is to have all grids of sandpaper in your work shop. The other products you can buy for less than 40 bucks, which is way cheaper than replaceing both headlights. You DONKEY
What are you talking about? you need some sand paper, a water bottle, a drop of dish soap, some microfiber towels, and an orbital polisher. If you're too poor to float under $50, not sure what to say.
Saya suka postingan dari AMD, sangat jelas urutannya, dikerjakan dengan perlahan, jadi aku bisa memahami urutannya,hasil pekerjaan luar biasa bagus, sukses selalu untuk AMD,
@@Audiobooks133 nope not at all buy your self some 3M painters tape and tape up all the painted surfaces surrounding the headlight on your vehicle to protect the paint and anything else you don’t wanna have a mistaken and hit with sandpaper then proceed 👍 hope this helps
How much? This was amazing work.. exactly what i was expecting to see.. this works for all plastic headlights? I have a 2016 panamara and the lights pop off easy. They have sone small scratches that i want removed
Because the first 800 grit was dry sanding. He probably wasn't satisfied with how it looked. Probably still had some scratches. So he repeated and couple steps back but kept it wet til the end of the sanding
I noticed a little stone chip on the headlight that didn’t come out with 180. Do you think if you had of worked that area a little longer or do a few more passes that stone chip would have come out eventually ?
Why so many different numbers. I accidentally put some scratches horizontally on headlight, lords nows what number it was too(coarse block). So I need to start w 800?
I used a headlight kit on my headlights and after sanding , compound , than polishing there’s a bunch of swirl marks left . Can I just buy some better compound and polish and apply to headlight or do I have sand them again ?
My car original headlight was completely destroyed and I bought a new one but now it's full of deep scratches and it's material is also little bit weak what should I do?
Yes he is right 800 grit will be hard to work with I would shoot for 400 grit or 200 if that’s not enough then. For best results worn your way up 200 grit at a time; until you reach 3,000 then make sure to add a protective coating so it lasts
Hello after sanding and polishing with gyeon compound + ona wool pad then finishing with menzerna super polish on a finishing pad, I have swirl marks left. Any ideas on how I can finish swirl free?
Looks amazing, for a headlight with clearcut failure ( renault clio iv) i could start by hand with the 400 grit ? Or only with machine ?, also a good quality sealant like labocosmetica cupido could protect the headlights of reaplied lets say maybe 5 months? Best regards and awesome job ;)
I just did a headlight . Started with a 1000 and went to 2000 then 2500 but once wiped I still have several areas that didn't clear. Should I go back to 800 and repeat the process? Also would a palm sander work or have to be high rpm ?
Kad vidim šta sve treba od materijala jeftinije mi je svratit do Sarajeva platit da to Alen odradi a ja u međuvremenu skoknem do Baše na ćevape pa do Egipta na šampite prošetam po Ferhadiji i svi sretni i zadovoljni ;-)
Bad job, should take 40 mins not 4/5 hours. The wipe on coating sucks also, its not designed for polycarbonate headlights and will not last long, would be more durable to spray it with a UV sealant clear coat specially designed for headlights. He also used way to much water during wet sanding. A much quicker, cheaper and better results process is: P500 dry, P800 Dry, 3M Trizact 3000 slightly wet, then machine polish with 3m plastic compound, then spray with UV clear seal.
Question for you... I am currently using all car pro products as well and have a new vehicle with swirl marks from the factory on the headlights b pillars and taillights... I am using reflect and a harbor freight ultra fine white foam polishing pad... I am getting extremely frustrated because it is not taking it out with the DA set to speed setting for (2/3 speed)... The b pillars still have swirls and maring from the DA... These plastic pieces are all I have left to do with my paint correction on the vehicle but I am getting super frustrated because reflect and the polishing pads worked great on the paint scratches and swirls!
After 6000 it was looking better then most of the cars you can see on the roads 😅 Final result was a 💣
Wow, how easy this is. You just need about 1000 dollars of equipment including compressor and grinder and about two hours of work for one headlight plus assembly. Love it
You don’t need a compressor or grinder. This can all be done by hand for $40 total.
@@AveryFreese Let me see the right video then. This is what I was searching for.
@@2winis2doit5 bro what are you on. lol you clearly never worked on cars before, if you do then you should know how easy it is to remove the headlight and how common it is to have all grids of sandpaper in your work shop. The other products you can buy for less than 40 bucks, which is way cheaper than replaceing both headlights. You DONKEY
What are you talking about? you need some sand paper, a water bottle, a drop of dish soap, some microfiber towels, and an orbital polisher. If you're too poor to float under $50, not sure what to say.
@@arabianwarrior7177yes I'm trying to remove some as well I just don't know the way about going by and doing it
Top top !!! Svaka cast majstore, imas opasnu ruku....
Hvala prijatelju
Ovo je perfektno! Svaka čast!
Hvala prijatelju
Great work, just did mine according to your guidlines. Thanks !😊
Drago mi je da vam je video poslužio i da ima pozitivan odjek.
Wow great job!!!
Outstanding results
tnx my friend
Saya suka postingan dari AMD, sangat jelas urutannya, dikerjakan dengan perlahan, jadi aku bisa memahami urutannya,hasil pekerjaan luar biasa bagus, sukses selalu untuk AMD,
Tnx friend and enjoy
Lot of works but the result is satisfying !
Bravo 💪
Tnx strance😂
Amazing job!!😮
Doktore
This is the best one I have seen on RUclips. You really take your time and pursue perfection. This is top tier work!
Tnx my friend and enjoy
Phenomenal!
Hi. Great results as always 👍🏽. May I know how long did you take to complete the process from start to finish for both left and right headlamps?
4/5 hours for both
@@Amddetailing to much time
Amazing job well done top ^^
Tnx friendd
Terima kasih banyak bang , illmu yang sangat bermanfaat sekali.
woaah
Your a Master in this field. Hey bud what sending paper would you recommend me using or having access to her in the USA ?
Is it necessary to remove the whole headlight or head lens assembly
@@Audiobooks133 nope not at all buy your self some 3M painters tape and tape up all the painted surfaces surrounding the headlight on your vehicle to protect the paint and anything else you don’t wanna have a mistaken and hit with sandpaper then proceed 👍 hope this helps
Great job 👍
Tnx bro😉
How much? This was amazing work.. exactly what i was expecting to see.. this works for all plastic headlights? I have a 2016 panamara and the lights pop off easy. They have sone small scratches that i want removed
Wowwww
Whyd you go back from 1500 to 800?
@@chuarmer9796 me too i didn't understand that
@@chuarmer9796 because 800 grit is final grit to paint
Because the first 800 grit was dry sanding. He probably wasn't satisfied with how it looked. Probably still had some scratches. So he repeated and couple steps back but kept it wet til the end of the sanding
awesome!
Awesome work! Why did you use 800 after going to 1500?
Yes
@@Amddetailing Sorry was trying to understand why did you have to go to 800 after 1500.
@@slav21 Yes
@@realktz5409 No
😂@@realktz5409
Vrhunski,jedno pitanje,posle vodobrusnog papira p1500 si išao sa p800 pa p2000,jel ima neki poseban razlog za to?
800 na masini je kao rucno 1500 al idem sa 800 da mi pokupi riseve sto ostanu od rucnog 1500
@@Amddetailing is that because wet sanding vs dry sanding?
P800 and 800 are two different things.
800 is somewhere between P1500 and P2000 on the other scale
Bravo 💪💪💪 ali ja mislim da bi danas sa Mirka i Kovex to brže uradio 😊
Pozdrav, kako znate da je 180 odradio svoj posao i da je fabrički sloj zaštite na faru skinut?
Jednpstavno vidis promjenu boje prilikom skidanja kako nestaje sloj zastite,imas u nekom od drugih videa prikazano kako to izgleda pa pogledaj
I noticed a little stone chip on the headlight that didn’t come out with 180. Do you think if you had of worked that area a little longer or do a few more passes that stone chip would have come out eventually ?
Why so many different numbers. I accidentally put some scratches horizontally on headlight, lords nows what number it was too(coarse block). So I need to start w 800?
I used a headlight kit on my headlights and after sanding , compound , than polishing there’s a bunch of swirl marks left . Can I just buy some better compound and polish and apply to headlight or do I have sand them again ?
I polish with the same products with which I polish the coating on the car and I have no problems
Could you use an electric palm sander instead of a air powered ?
Electric is much better for work than air
My car original headlight was completely destroyed and I bought a new one but now it's full of deep scratches and it's material is also little bit weak what should I do?
They can be made in 95% of cases because the plastic is thick enough to be sanded
@@Amddetailing thanks a lot brother
I have a lot of minor swirls on my headlights, should I start with 800 grit then 1000, 2000, 3000, 6000?
800 IMO
800 is the minimum, I’ve started with 400 on some headlights, depends on how bad they are. You don’t need to go beyond 2000 either.
Yes he is right 800 grit will be hard to work with I would shoot for 400 grit or 200 if that’s not enough then. For best results worn your way up 200 grit at a time; until you reach 3,000 then make sure to add a protective coating so it lasts
Bro ,too much work maaan
What is that polishing machine the man is using any answers please thank you 😊
Random orbital sander
Are you still use wet sanding method till now?
No
Not sure you should have to sand more than once for deep scratches and use 3M polishing compound with a polisher instead of a sander to finish.
Sander speed rpm?
Hello after sanding and polishing with gyeon compound + ona wool pad then finishing with menzerna super polish on a finishing pad, I have swirl marks left. Any ideas on how I can finish swirl free?
Look video
Do yo use only water? Or some kind of lubricant?
water and detergent for judges
@@Amddetailing thanks! So you mean soap for clothes? I understand detergent but judges i cant..
Great work!
@@jojoenderest90 yes soap and water heheheh tnx bro😘
Once you said headlights will a tint hold ok on my lights my car is 2012
Waooooo
Hvala 😉😉😉
Looks amazing, for a headlight with clearcut failure ( renault clio iv) i could start by hand with the 400 grit ? Or only with machine ?, also a good quality sealant like labocosmetica cupido could protect the headlights of reaplied lets say maybe 5 months? Best regards and awesome job ;)
Searth polymer vapour, its the easiest to apply and gives you the best finnish, its on aliexpress
Where u guys located at I need this done asap
Im from Bosnia,Sarajevo
Os this Toyota Carina II headlight bro?
Mine needs polishing too..
Can I join your master polisher special club?
Imas li neki cenovnik poliranja farova, poliranja auta itd?
Auto dok se ne vidi stanje nemogu reci cijenu,farovi od 200 km pa gore
Wondering how muxh does it cost to repair one headlight. Mine requires too to repair from deep scratch
200 /300 euro
Can I do the same step with 3m paper ?
yes
👍👍
What do I do wrong when some sanding marks are left in the headlight? I try to sand evenly by hand but some straight marks are always left
pressure on the machine, speed of the machine, type of paper, short work between switching to another paper granulation, etc
Koliko vremena ti je stajala keramika pre brisanja MF krpom???
Hvala
Svaka čast na radovima💪🏽💪🏽💪🏽💪🏽💪🏽
Dok ne krenene mjenjati boju to sve zavisi od keramike i od proizvodzaca od 30 sec do 5 min
Sir, please show how to remove straches from car windshield glass
You have video on my channel
I just did a headlight . Started with a 1000 and went to 2000 then 2500 but once wiped I still have several areas that didn't clear. Should I go back to 800 and repeat the process? Also would a palm sander work or have to be high rpm ?
Go back to 800 on the bad areas. I’ve started with 400 on some headlights that were really bad
@@ronb9901 I appreciate that
@@jimmyallen3850 also a palm sander is just fine.
Great video how did you determine the types of sandpaper you have to use?
thank you
Tnx ,experience and I always start with 400 if it goes slow I go to a smaller 320,280,140 etc.
Kad vidim šta sve treba od materijala jeftinije mi je svratit do Sarajeva platit da to Alen odradi a ja u međuvremenu skoknem do Baše na ćevape pa do Egipta na šampite prošetam po Ferhadiji i svi sretni i zadovoljni ;-)
Hehehehe sve moze
jel to na suvo ide od 180?
Ide
4 to 5 hours for the 1 lens only?
yes, because this headlight was totally destroyed and had to be done so that it was not noticed that it was damaged
Q prooo
Tnx bro
Where can I find the sanding machine you are using.please?
Mirka official page
How much would you charge for that particular job that I just watched every
about as much as the headlight costs
koliko je debela plastika fara ?
Koliko kosta ovo zadovoljstvo?
450 eura
Very cool! But for a single job, it is easier and cheaper to buy new headlights.
this type of headlight for this Porsche costs close to 2000 euros, so I don't think it's cheaper
lol what modern headlight is cheaper than sanding and polishing
what these videos don't explain is that you take out all the UV protection. So after a few months, the headlights will yellow
after my work, I put either ppf foil or ceramic protection on the headlights, it's not on the video, but it's on my fb page, so you can take a look
You should hawe juste clear theme after it better
Ok
I stopped at 3000, than tried turtle wax compound. And plastic. Still see lot of fine scratches
Should I go to 5000, and 6000?
The wax doesn't last very long and washes off quickly, the best protection is the PPF film
Better to buy new one😂😂
why cant they just make them out of glass??
brate sto si toliko pojacao muzuku
Talk and explain
it would be thumb up if NO dumb music.
here is shown the work and how to solve who is interested does not care about music.
You can't please everyone
You can always lower the volume. If not YOU chose to listen to the music.
Bolje ne može
Very noisy
Useless product?
Bad job, should take 40 mins not 4/5 hours. The wipe on coating sucks also, its not designed for polycarbonate headlights and will not last long, would be more durable to spray it with a UV sealant clear coat specially designed for headlights. He also used way to much water during wet sanding. A much quicker, cheaper and better results process is: P500 dry, P800 Dry, 3M Trizact 3000 slightly wet, then machine polish with 3m plastic compound, then spray with UV clear seal.
Had to dislike video too many Trump ads I don’t need to see that MAGA bullsh_t brah
He complains to Trump about what I have to do with his ads
Question for you... I am currently using all car pro products as well and have a new vehicle with swirl marks from the factory on the headlights b pillars and taillights... I am using reflect and a harbor freight ultra fine white foam polishing pad... I am getting extremely frustrated because it is not taking it out with the DA set to speed setting for (2/3 speed)... The b pillars still have swirls and maring from the DA... These plastic pieces are all I have left to do with my paint correction on the vehicle but I am getting super frustrated because reflect and the polishing pads worked great on the paint scratches and swirls!
you have to change the method, some pillars are too soft and leave marks, you have on my channel just how such a pillar is polished
How many hours did the whole process take in total? Day? Thanks
3 hour one headlights
@@Amddetailing
Wouldn't it have been a lot faster to flat them with 800 then clearcoat?