Hi this is a great video thanks a lot, does the comfort control module you took out work the windows on both sides, as mine has stopped, also heated mirrors stopped working along with central locking light when locking, Audi B6 avant ! thanks again.
Perfect! Have to do this tomorrow as I had a big flood into my Avant, looks like it came in via a deteriorated pollen filter housing, which is apparently far too common on these. Very possible my ECU could be flooded so need to get that out ASAP! Do I have to disconnect the battery to do this, as you didn't say? Many thanks
I have that comfort module problem and i have to change it and what i found the code is a little bit different and i wonder if it works my audi is a6 c5 1997
When replacing the comfort control module is any reprogramming required, key fobs,etc? Or is it just plug in the new module and you're back I business?
Hi. I didn't program mine. But you can program each one yourself if you do it right. I program mine without any help. The car will automatically program each module if you do it properly
Hello i have a question. Is it safe to disconnect the ccm and drive around without it? I have my hazards stay on all the time like low beams. Switched the relay but norhing. My carpet wet where the module should be so im planning to remove the module and leave it indoor to dry but i need to drive around and etc. So my question is it safe to drive around without the module connected? Will i be having more problems later after connecting it or all should be fine and it wont mess anything up?
The CCM usually connects to the immobilizer, so you probably won't be able to start the car without it. Removing it would also give you multiple terminal 30 open circuit issues and low voltage across multiple sensors as well as disrupting the can bus data feed. You back up lights are also controlled by the CCM. So ya, don't take it out.
Hi The climate controls On My Audi a4b8 do not appear on The MMI screen I have tried to access 07 control module with OBD 11 PRO but module will not respond so do I need to replace comfort control module?
hello, I have problem after the rain, my car filled with water and gives some electronic errors, like an alarm. what can I do, how can i dry? thank you have you good day 2001 Audi A6 allroad c5 2.5tdi
First of all, do some research into blocked drainage holes, and this was the most likely cause. Next you'll have to remove the module and check it for damage, or get a replacement one. Used on eBay is a good way to save money. Best of luck! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Total Technik without the support of people like you! You can donate by PayPal - just go to www.paypal.me/totaltechnik 2) Please ensure you subscribe to our RUclips channel. 3) Please give our video's the Thumbs Up on RUclips. 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!
Yes, you can usually get a look at it. Just put the seat all the way back and you should be able to manipulate the carpet up enough to get a peek inside. Best of luck! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Total Technik without the support of people like you! You can donate by PayPal - just go to www.paypal.me/totaltechnik 2) Please ensure you subscribe to our RUclips channel. 3) Please give our video's the Thumbs Up on RUclips. 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!
Not currently I'm afraid. Maybe in the future though! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Total Technik without the support of people like you! You can donate by PayPal - just go to www.paypal.me/totaltechnik 2) Please ensure you subscribe to our RUclips channel. 3) Please give our video's the Thumbs Up on RUclips. 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!
hello genius !! I have audi A4 2006 and the comfort control module my mechanic told me that it is broken, the glass and the door control do not work! my question is that mine ends with two letters that are BC, and I could find CG, they both have the same numbers but only the letters change at the end !! I tried the new one but nothing worked, should I put a code for this to work or how should I do it?
With the comfort control modeul itself we would recommend replacing only with another unit that has a 100% indentical part number. The letters at the end are generally the revision code, and if it does not match then there is a chance of it not being compatible or you having issues. That said, your unit may have been superseded, and Audi can advise the latest part number for your exact part. Replacig it with the superceed one of course is ok. Best option is to buy used on eBay and wait until one with the exact same number comes up. That way you can be sure of a smooth changeover. --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Total Technik without the support of people like you! You can donate by PayPal - just go to www.paypal.me/totaltechnik 2) Please ensure you subscribe to our RUclips channel. 3) Please give our video's the Thumbs Up on RUclips. 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!
After torrential rain in Ireland, my doors stopped working with the key fob, my windows stopped working, boot & fuel cap cover, took out the CCM box under the seat on the passenger side and the light to say the boot is on went off there was water in the CCM's housing box too. It's on my skoda superb from 2005 the PD 130 model, I ordered a new one it's due tomorrow it has the same model number as my old one, do you think it will be a straight swap or will I have to do some programming for it?
@@Osvaldo-pw2lc Didn't have to program mine, I had to get the second key and put in the drivers side door lock and press the buttons on it and have the main key in the ignition. Be sure to check your fuse if your have problems, mine went a second time and second time I swapped out the fuse and it fixed mine. Not 100% sure but think it was fuse number 14 or else 9 but google it and you will find out
My comfort control module got wet I replaced it and Horan windshield wipers turn signals windows convertible top all don’t work Fuses are still good what could be the issue
Does this module have anything to do with my sound in my car... I change the amplifier and now I only have sound coming out of one door... my driver side... and my driver side window is acting funny as well with going up and down.. and I brought a brand new switch and it’s still having a problem going up and down but my main concern is my music in my car... the inside of my car had gotten wet then everything with my sound happened no spun at at until I got the amplifier and then I got sound but only out of the driver door...at this point I don’t know what’s wrong... oh I have 2008 Audi A6 Quattro A-line..
Hey, can tell me why water is found at the bottom of the driver seat? Around the Control Module, I keep finding water down there which shortage my module out.
Is your car an Avant model? If so, this is likely a leaking washer fluid pipe or pipe joint. There is a pipe that feeds washer fluid to the rear that passes under the carpet here. Usually green plastic. It has a join near where you left foot would sit from memory, and that often pops off. You'll want to pop the front carpet up and find this find and inspect it. Could be other things also, but that would be the first thing to check. Very common issue. Best of luck! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Total Technik without the support of people like you! You can donate by PayPal - just go to www.paypal.me/totaltechnik 2) Please ensure you subscribe to our RUclips channel. 3) Please give our video's the Thumbs Up on RUclips. 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!
Hello great videos.Will this be similar procedure on later model agents from around 2004? Also are the modules coded to the car? My colleague went through a puddle so I'm guessing the module is what is causing issues
Yes, it depends on the model of course, but many have this same type of set up. Modules can be coded to the car sometimes, depending on age and model etc. You can often just swap these over with no coding provided the part number of the replacement exactly matches the original. --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Total Technik without the support of people like you! You can donate by PayPal - just go to www.paypal.me/totaltechnik 2) Please ensure you subscribe to our RUclips channel. 3) Please give our video's the Thumbs Up on RUclips. 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!
Ok so I ordered replacement ccm for my 05 Audi A4 quattro 1.8t all part numbers match when I swapped it over the hazard lights go crazy for a few minutes then stop till I open a door or turn the key ,put old one back in no crazy hazard lights just want to get door locks working and alarm do you think the bad ccm tripped the alarm system immobilizer the alarm horn is unplugged cause it doesn't stop making noise
Asking because there is little info on this subject only that it's somewhere behind the front bumper and nothing else. And is it possible to access without removing the bumper?
Yes, it is on the bumper bar. Unfortunately I cannot recall offhand whether you can access it on the C5 without removing the bumper. I'm thinking likely not, but worth a look underneath before you remove the bumper just in case. On the RS6 things are very tight for space, but on smaller engined models access may be better! Let us know how you get on. --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Total Technik without the support of people like you! You can donate by PayPal - just go to www.paypal.me/totaltechnik 2) Please ensure you subscribe to our RUclips channel. 3) Please give our video's the Thumbs Up on RUclips. 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!
Hey there! No specific fault, this video is just showing where it is and how to remove it :-) --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Total Technik without the support of people like you! You can donate by PayPal - just go to www.paypal.me/totaltechnik 2) Please ensure you subscribe to our RUclips channel. 3) Please give our video's the Thumbs Up on RUclips. 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!
Hey there world, I have a problem with my "13" A8. When I turn the steering wheel it's making the engine go into neutral and sometimes even killing the car completely, it seems like this is so rare of a problem that even audi is having a hard time figuring out what the cause is... can anyone has heard of anything like this ever happening and have a solution can you please help...thank you and everyone stay safe!!
Looking for tools?
www.totaltechnik.com/selectstore
Is in the same side on the audis with the driver side on left????
Hi this is a great video thanks a lot, does the comfort control module you took out work the windows on both sides, as mine has stopped, also heated mirrors stopped working along with central locking light when locking, Audi B6 avant ! thanks again.
Perfect! Have to do this tomorrow as I had a big flood into my Avant, looks like it came in via a deteriorated pollen filter housing, which is apparently far too common on these. Very possible my ECU could be flooded so need to get that out ASAP! Do I have to disconnect the battery to do this, as you didn't say? Many thanks
I know Im kinda randomly asking but do anyone know of a good website to stream newly released tv shows online ?
Is it connected to the remote control key as well or is there another module for this? How to get to it?
I have that comfort module problem and i have to change it and what i found the code is a little bit different and i wonder if it works my audi is a6 c5 1997
is this on the same side on a LHD allroad? under the driver side?
When replacing the comfort control module is any reprogramming required, key fobs,etc? Or is it just plug in the new module and you're back I business?
Hi. I didn't program mine. But you can program each one yourself if you do it right. I program mine without any help. The car will automatically program each module if you do it properly
So if i change the module it doesnt matter to be the precise number as the one or? @@Zaa0909az
thank you
Is this module in anyway responsible for the starting of the car?or does it contribute to the starting of the car?
If the module was flooded what to do?? I got central locking issues..
hello, is this the same for Audi A4 B6?
Do you have to reprogram the key fobs?
Hello i have a question.
Is it safe to disconnect the ccm and drive around without it?
I have my hazards stay on all the time like low beams.
Switched the relay but norhing.
My carpet wet where the module should be so im planning to remove the module and leave it indoor to dry but i need to drive around and etc.
So my question is it safe to drive around without the module connected?
Will i be having more problems later after connecting it or all should be fine and it wont mess anything up?
The CCM usually connects to the immobilizer, so you probably won't be able to start the car without it. Removing it would also give you multiple terminal 30 open circuit issues and low voltage across multiple sensors as well as disrupting the can bus data feed. You back up lights are also controlled by the CCM. So ya, don't take it out.
@@EPTRotorsports sry i already did it but i got 0 problems. I dried it out and put back together and all is well.
Hi The climate controls On My Audi a4b8 do not appear on The MMI screen I have tried to access 07 control module with OBD 11 PRO but module will not respond so do I need to replace comfort control module?
hello, I have problem after the rain, my car filled with water and gives some electronic errors, like an alarm. what can I do, how can i dry? thank you have you good day 2001 Audi A6 allroad c5 2.5tdi
First of all, do some research into blocked drainage holes, and this was the most likely cause. Next you'll have to remove the module and check it for damage, or get a replacement one. Used on eBay is a good way to save money. Best of luck!
---
To help support us (for both you and others reading this) there are a few things you can do:
1) Donations both needed and welcome! We cannot operate Total Technik without the support of people like you! You can donate by PayPal - just go to www.paypal.me/totaltechnik
2) Please ensure you subscribe to our RUclips channel.
3) Please give our video's the Thumbs Up on RUclips.
4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us.
Thank you for your support!
Any chance this can be done without removing the seat? Even just to get a bit of look in to see if it's wet?
Yes, you can usually get a look at it. Just put the seat all the way back and you should be able to manipulate the carpet up enough to get a peek inside. Best of luck!
---
To help support us (for both you and others reading this) there are a few things you can do:
1) Donations both needed and welcome! We cannot operate Total Technik without the support of people like you! You can donate by PayPal - just go to www.paypal.me/totaltechnik
2) Please ensure you subscribe to our RUclips channel.
3) Please give our video's the Thumbs Up on RUclips.
4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us.
Thank you for your support!
Hi TT , do you have any video on the A4 b6 Cab storage rack in the boot ? cheers
Not currently I'm afraid. Maybe in the future though!
---
To help support us (for both you and others reading this) there are a few things you can do:
1) Donations both needed and welcome! We cannot operate Total Technik without the support of people like you! You can donate by PayPal - just go to www.paypal.me/totaltechnik
2) Please ensure you subscribe to our RUclips channel.
3) Please give our video's the Thumbs Up on RUclips.
4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us.
Thank you for your support!
hello genius !! I have audi A4 2006 and the comfort control module my mechanic told me that it is broken, the glass and the door control do not work! my question is that mine ends with two letters that are BC, and I could find CG, they both have the same numbers but only the letters change at the end !! I tried the new one but nothing worked, should I put a code for this to work or how should I do it?
With the comfort control modeul itself we would recommend replacing only with another unit that has a 100% indentical part number. The letters at the end are generally the revision code, and if it does not match then there is a chance of it not being compatible or you having issues.
That said, your unit may have been superseded, and Audi can advise the latest part number for your exact part. Replacig it with the superceed one of course is ok.
Best option is to buy used on eBay and wait until one with the exact same number comes up. That way you can be sure of a smooth changeover.
---
To help support us (for both you and others reading this) there are a few things you can do:
1) Donations both needed and welcome! We cannot operate Total Technik without the support of people like you! You can donate by PayPal - just go to www.paypal.me/totaltechnik
2) Please ensure you subscribe to our RUclips channel.
3) Please give our video's the Thumbs Up on RUclips.
4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us.
Thank you for your support!
I have the Same problem, can you please ask me how did you fixed it
After torrential rain in Ireland, my doors stopped working with the key fob, my windows stopped working, boot & fuel cap cover, took out the CCM box under the seat on the passenger side and the light to say the boot is on went off there was water in the CCM's housing box too. It's on my skoda superb from 2005 the PD 130 model, I ordered a new one it's due tomorrow it has the same model number as my old one, do you think it will be a straight swap or will I have to do some programming for it?
Did the CCM fix your problems and did you have to program it?
@@Osvaldo-pw2lc Didn't have to program mine, I had to get the second key and put in the drivers side door lock and press the buttons on it and have the main key in the ignition. Be sure to check your fuse if your have problems, mine went a second time and second time I swapped out the fuse and it fixed mine. Not 100% sure but think it was fuse number 14 or else 9 but google it and you will find out
My comfort control module got wet I replaced it and Horan windshield wipers turn signals windows convertible top all don’t work Fuses are still good what could be the issue
Did you get this fixed Brandon? i have same issue its a fuckin nightmare 😅
Does this module have anything to do with my sound in my car... I change the amplifier and now I only have sound coming out of one door... my driver side... and my driver side window is acting funny as well with going up and down.. and I brought a brand new switch and it’s still having a problem going up and down but my main concern is my music in my car... the inside of my car had gotten wet then everything with my sound happened no spun at at until I got the amplifier and then I got sound but only out of the driver door...at this point I don’t know what’s wrong... oh I have 2008 Audi A6 Quattro A-line..
Did you fix yor car?
Do I have to disconnect the battery before removing the black box?
Im afraid of VAG com clear code when changing the box
Never disconnect the battery supply that will throw your codes out and you will have to go too the dealership
@@Zaa0909azso that's why mine is still not working?
Hey, can tell me why water is found at the bottom of the driver seat? Around the Control Module, I keep finding water down there which shortage my module out.
Is your car an Avant model? If so, this is likely a leaking washer fluid pipe or pipe joint. There is a pipe that feeds washer fluid to the rear that passes under the carpet here. Usually green plastic. It has a join near where you left foot would sit from memory, and that often pops off. You'll want to pop the front carpet up and find this find and inspect it. Could be other things also, but that would be the first thing to check. Very common issue. Best of luck!
---
To help support us (for both you and others reading this) there are a few things you can do:
1) Donations both needed and welcome! We cannot operate Total Technik without the support of people like you! You can donate by PayPal - just go to www.paypal.me/totaltechnik
2) Please ensure you subscribe to our RUclips channel.
3) Please give our video's the Thumbs Up on RUclips.
4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us.
Thank you for your support!
@@TotalTechnik Thanks you. I will check it out.
Where is tha Audi A6 gateway module location plz tell me 2013 model car
Plz send me bro gateway module location of Audi A6 2013 model car
Hello great videos.Will this be similar procedure on later model agents from around 2004? Also are the modules coded to the car?
My colleague went through a puddle so I'm guessing the module is what is causing issues
Yes, it depends on the model of course, but many have this same type of set up. Modules can be coded to the car sometimes, depending on age and model etc. You can often just swap these over with no coding provided the part number of the replacement exactly matches the original.
---
To help support us (for both you and others reading this) there are a few things you can do:
1) Donations both needed and welcome! We cannot operate Total Technik without the support of people like you! You can donate by PayPal - just go to www.paypal.me/totaltechnik
2) Please ensure you subscribe to our RUclips channel.
3) Please give our video's the Thumbs Up on RUclips.
4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us.
Thank you for your support!
Ok so I ordered replacement ccm for my 05 Audi A4 quattro 1.8t all part numbers match when I swapped it over the hazard lights go crazy for a few minutes then stop till I open a door or turn the key ,put old one back in no crazy hazard lights just want to get door locks working and alarm do you think the bad ccm tripped the alarm system immobilizer the alarm horn is unplugged cause it doesn't stop making noise
Hey, can you make a video how to change the horn on audi a6 c5? Thank you.
Asking because there is little info on this subject only that it's somewhere behind the front bumper and nothing else. And is it possible to access without removing the bumper?
Yes, it is on the bumper bar. Unfortunately I cannot recall offhand whether you can access it on the C5 without removing the bumper. I'm thinking likely not, but worth a look underneath before you remove the bumper just in case. On the RS6 things are very tight for space, but on smaller engined models access may be better! Let us know how you get on.
---
To help support us (for both you and others reading this) there are a few things you can do:
1) Donations both needed and welcome! We cannot operate Total Technik without the support of people like you! You can donate by PayPal - just go to www.paypal.me/totaltechnik
2) Please ensure you subscribe to our RUclips channel.
3) Please give our video's the Thumbs Up on RUclips.
4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us.
Thank you for your support!
Whats da falt?
Hey there! No specific fault, this video is just showing where it is and how to remove it :-)
---
To help support us (for both you and others reading this) there are a few things you can do:
1) Donations both needed and welcome! We cannot operate Total Technik without the support of people like you! You can donate by PayPal - just go to www.paypal.me/totaltechnik
2) Please ensure you subscribe to our RUclips channel.
3) Please give our video's the Thumbs Up on RUclips.
4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us.
Thank you for your support!
Hey there world, I have a problem with my "13" A8. When I turn the steering wheel it's making the engine go into neutral and sometimes even killing the car completely, it seems like this is so rare of a problem that even audi is having a hard time figuring out what the cause is... can anyone has heard of anything like this ever happening and have a solution can you please help...thank you and everyone stay safe!!