I was first a little skeptical. But seeing it in action, convinced me that it was very useful. But I think you need to know what you are doing, because of the resistance you can put on your gear and engine
An interesting experiment. However, it was immediately clear that a disk with such a lot of bolts and nuts would be too heavy. Especially compared to a light spool of trimmer line. in addition, all the bolts located in the second and third circles closer to the center are not needed at all because they do not have time to work, all the work is done by the cutting elements located on the outer orbit. This is how a trimmer line works and this is how a disk with pobedite potions works.
Вывод-не получилось.Пыли много+смерть тримеру.Лайк за творение. Плохой результат,тоже результат.Все в жизни не сразу получалось. Твори и ни кого не слушай.
fantastic ,but mecanilly it can be destoyed by the oaf during function (the bearing and the shaft)try to sharpen the end of bolts for reducing the resistance
Design analysis of needs 1) Obviously a dirt-deflector! You do nor want your soil in your neighbours garden.. The soil has to be caught and redeposited no more than a yard to the side. Perhaps an old tire could be cut up and used for that. 2) The shaft from engine to business-end, is really not helping you! There is a torque that eventually will make 'something' break. 3) Weight and ergonomic stress on your body. It will only take a limited time before you will feel the stress of the friction against the ground, as pain.. The length of the shaft only add to this! So.. a Keep the dirt under control b Get rid of the shaft c Dont carry the contraption a+b+c = Lawn-mover with dirt-disk! A Weed-eater is not optimal platform. A lawn-mover would be better!
Jedan mali savet, serviser koji odrzava moj trimer me je posavetovao da nakon upotrebe, trimer drzim uspravno (motor da bude gore) dok se ne ohladi, ako stoji nagnut ka dole, ulje iz glave za secenje sliva se niz cev i tu se ohladi i zalepi, i onda supcanici rade suvi. Pozdrav iz Srbije.
Pozz za Srbiju ;) Ja sam trimer morao tako stavit jer je u pitanju bilo mijesto za njega kojeg nema u garazama tak da sam ga tako stavio videvši kako su u tim salonima stavljeni tak sam i ja stavio svoj :D Ali ima nesta u tome hehehe Ja preferiram da trimer ostavim vertikalno ali kad nemam mijesta :D
Doctor D.S. Da,da tako i ja drzim svoj. Napisao sam ovo jer ja nisam imao pojma da tako treba dok nisam kupio trimer, ali kad razmislim ima logike. Super su ti klipovi, samo tako nasavi! :)
I would try and cut away some of the unnecessary metal plating if you can also try 1", 2" and 3" in pattern that way not all trying to dig into dirt at same time until you have already gone thru the longer bolts also look into 3D printing something like this I think it would be fun and very educational. Ok I need to finish watching to see if you made any changes
A good idea! I can imagine the dust storm you can create. As a small engine enthusiast, please allow me to share some info. The extra weight will indeed affect smaller cc engines, and after some time will affect your clutch. Stronger engines, of course will fare better, but I like the concept.
This is exactly what I need!! I’m tired of clearing weeds manually from my garden every spring! Wished they sold this somewhere! How many cc does the motor have to be for this to work?
Everything is fine. If you sharpened (grinded) the rim of the circular plate and pressed punch-type or screwdriver-type tips to make a better use of the work of the disc you made. Tudo está bem. Se você afiou (afiou) a borda da placa circular e pressionou pontas do tipo punção ou chave de fenda para aproveitar melhor o trabalho do disco que você fez
Мало того редуктору писец прийдёт ещё и вал разобьёт ..но это пол беды ..болт вырвавшись из диска убить может и щиток не поможет ..не вздумайте делать такое ..проще удт тогда цепь бензопилы ..хотя тоже редуктор нагружает ..леска вот выход меняй почаще и все гуд будет ) удачи садоводы !!
Great idea sir, I made this plate of screw at home, but lot of weight in disc plate because of screw, screw size is 2'' long, please suggest does this will affect the top gear of brush cutter or its engine. Please suggest
Great for mascerating the crap outta a covercrop before tarping using a bit higher & lighter touch so as not to disturb too much soil...like a power harrow set on the highest setting.
Is it even tilling the actual ground? I can't tell but it looks like it's just getting rid of the weeds...which is great...but didn't it already do that?
I'm also thinking of using an old 7 1/4 inch saw blade with portions of the blade cut 2 to 3 inches from the outside edge towards the center and bent at 90 degrees.
Картоху вместе с колорадом месить пойдет! Чтоб никаму не досталась!А идея заи.ись скора такой диск будет в стандартной комплекташке всех триммеров :попробовал -иди за новой косой!и в магазе менеджер будет впаривать:берите смелее у меня такойже 4 года.
Я так понимаю что " это" должно было избавить тебя от сарняка.Но это чудо не справилось с задачей ,оно просто срезало верхушки травы,и на следующей неделе она снова вырастет!Ну если ленишся полоть ,поставь леску 4-5мл. и скоси ,выйдет тоже самое ,даже лучше ,потому что трава не скосилась и она по-прежнему торчит .
@dedamiloje6723 Tačno tako ploča je prevelika tj. prevelika rotirajuća masa što je opasno. Dvostruki nož iz prodavnice bolji i Sigurniji od ovoga....izgubljeno vreme za izradu....
Bom dia. Fiz 1:dessa mas coloquei uma proteção em volta do disco para não deixar a terra e outros objetos serem arremessados para longe e correr o risco de acidente com alguém próximo
Need to watch that drill ! It will grab them headphones quick ! Not bad. But almost seemed like the regular weed whacker would do about as good. One big difference I noticed is you wouldn't have to constantly have to keep putting line on it ! ! Like you said if it was a bigger machine is think there would be better results with the garden clearing part. .
лайк за трудолюбие,но!!! опасно такой инструмент использовать - выбрация на макс.оборотах наверняка бешеная + не дай БОГ гайка отлетит в кого ни будь......семь раз отмерь и один раз подумай правильно ли отмерил.......
Or you can spend $110 and less time and buy a tiller attatchment.. All in all good experiment. It would probably make a hell of a brush hog attatchment.
Hay guy , the in improvement you need to make is starting at one point use a use a 1/2 lainth screw 3 of them in the outer perimeter then move up 1 inch every set of three tell you get back to the first 1/2 screw then make a pie like shape ,,,,,, from the outer perimeter looking to the center of the disk place that size screw tell you reach the center of the disk , then place it on the weed eater ,,,,then add wait to the outer perimeter to balance the disk like a car tire weld them down so thay dont fly off
Going to build myself one of these with a 9” disc just for corn! Excellent idea!
Brilliant idea. But have you tried less and longer screws. No ale dobra robota dobry pomysł i wykonanie oraz talent. Gratulacje🤗
I was first a little skeptical. But seeing it in action, convinced me that it was very useful. But I think you need to know what you are doing, because of the resistance you can put on your gear and engine
Super idea. It also helps to spreading and dusting mud.
An interesting experiment. However, it was immediately clear that a disk with such a lot of bolts and nuts would be too heavy. Especially compared to a light spool of trimmer line. in addition, all the bolts located in the second and third circles closer to the center are not needed at all because they do not have time to work, all the work is done by the cutting elements located on the outer orbit. This is how a trimmer line works and this is how a disk with pobedite potions works.
Вывод-не получилось.Пыли много+смерть тримеру.Лайк за творение. Плохой результат,тоже результат.Все в жизни не сразу получалось. Твори и ни кого не слушай.
Great idea to wear out the clutch in record time as well as overloading the motor until it overheats.
Excelent! Succes,in continuare,spor,sănătate!
Когда не привареная гайка открутиться или прорвется через метал болт со скоростью пули политит
Good job . I like it .👍👍👍
Add water just a little. 👍
fantastic ,but mecanilly it can be destoyed by the oaf during function (the bearing and the shaft)try to sharpen the end of bolts for reducing the resistance
ثصصضضضضض1ضضضضضضضضضض
Great idea, but maybe a couple bits of welded chain instead of bolts might be a bit more durable.
Design analysis of needs
1) Obviously a dirt-deflector! You do nor want your soil in your neighbours garden..
The soil has to be caught and redeposited no more than a yard to the side.
Perhaps an old tire could be cut up and used for that.
2) The shaft from engine to business-end, is really not helping you!
There is a torque that eventually will make 'something' break.
3) Weight and ergonomic stress on your body.
It will only take a limited time before you will feel the stress of the friction against the ground, as pain..
The length of the shaft only add to this!
So..
a Keep the dirt under control
b Get rid of the shaft
c Dont carry the contraption
a+b+c = Lawn-mover with dirt-disk!
A Weed-eater is not optimal platform. A lawn-mover would be better!
Burazz hvala ti na reklamiranju❤❤
I svakaa castt buraz najbolji si i samo naprijed❤ uz tebe sam ❤
Hvalaa careee
Excellent work
Jedan mali savet, serviser koji odrzava moj trimer me je posavetovao da nakon upotrebe, trimer drzim uspravno (motor da bude gore) dok se ne ohladi, ako stoji nagnut ka dole, ulje iz glave za secenje sliva se niz cev i tu se ohladi i zalepi, i onda supcanici rade suvi. Pozdrav iz Srbije.
Pozz za Srbiju ;)
Ja sam trimer morao tako stavit jer je u pitanju bilo mijesto za njega kojeg nema u garazama tak da sam ga tako stavio videvši kako su u tim salonima stavljeni tak sam i ja stavio svoj :D
Ali ima nesta u tome hehehe
Ja preferiram da trimer ostavim vertikalno ali kad nemam mijesta :D
Doctor D.S. Da,da tako i ja drzim svoj. Napisao sam ovo jer ja nisam imao pojma da tako treba dok nisam kupio trimer, ali kad razmislim ima logike. Super su ti klipovi, samo tako nasavi! :)
Hvalaa tiii
I would try and cut away some of the unnecessary metal plating if you can also try 1", 2" and 3" in pattern that way not all trying to dig into dirt at same time until you have already gone thru the longer bolts also look into 3D printing something like this I think it would be fun and very educational. Ok I need to finish watching to see if you made any changes
A good idea! I can imagine the dust storm you can create. As a small engine enthusiast, please allow me to share some info. The extra weight will indeed affect smaller cc engines, and after some time will affect your clutch. Stronger engines, of course will fare better, but I like the concept.
0
This is exactly what I need!! I’m tired of clearing weeds manually from my garden every spring! Wished they sold this somewhere!
How many cc does the motor have to be for this to work?
👍 se puede probar . Me gusta . Very good
That's a great way to expose yourself to anthrax
Good idea bro💡
Everything is fine. If you sharpened (grinded) the rim of the circular plate and pressed punch-type or screwdriver-type tips to make a better use of the work of the disc you made.
Tudo está bem. Se você afiou (afiou) a borda da placa circular e pressionou pontas do tipo punção ou chave de fenda para aproveitar melhor o trabalho do disco que você fez
Interessante, mas provavelmente estraga a roçadeira por falta de torque e uma transmissão mais robusta.
отлично...техника должна работать во благо...
Stihl already makes a great tiler attachment for there trimmers.
You're the Mad Max of lawn and garden care
good video..you are so creative ...Good Job!
Super video and music. Thanks
Thank you sir
Great effort! I always thought about doing the same thing! Keep up the great videos Sir
Good idea 💡
K11k 111 1k11
Мало того редуктору писец прийдёт ещё и вал разобьёт ..но это пол беды ..болт вырвавшись из диска убить может и щиток не поможет ..не вздумайте делать такое ..проще удт тогда цепь бензопилы ..хотя тоже редуктор нагружает ..леска вот выход меняй почаще и все гуд будет ) удачи садоводы !!
Блин.. Дружище вовремя ты написал.. А-то я уже загорелся.. Эээх.. Ленивый я.. 😢
Nagyon jó szuper egyszerű sok lehetöséget ad és érthető volt ķöszönóm szépen a feltöltését 💙❤💛
сама идея хорошая но слишком грамоская ,будет разбивать редуктор и сцепление
Odlican kao i uvijek i kada sam gledao video kad si radio novu radionu vidio sam da se mnogo trudis i jedno pitanje koju si skolu zavrsio
Hvalaa puno od
A dobro nema veze ali radis kao majstor
Daa to je bitnoo
На сколько хватит редуктора???
More video about tools garden sir. And God bless you
I love your idea.. very clever idea. Thank you for this very informative channel of you. I learn a lot. Thank you for sharing.
Cool but let’s see what it does in a bunch of bind weeks.
Great idea sir, I made this plate of screw at home, but lot of weight in disc plate because of screw, screw size is 2'' long, please suggest does this will affect the top gear of brush cutter or its engine. Please suggest
Самое плохое что можно придумать для убийства аппарата!
Niko nema dosjetljivljiji od nas balkanaca !!!
Bomee nemaaa
This looks incredibly dangerous.
Good idea and good build, is that machine an FS55?
Tnx ;) that :D
Simple but the best😍👌👌👌
Tnx broo :D
Вижу не только мне эта затея херней показалась.....
experiment is good but your trimmer speed is very high, the power of low speed trimmer is best in soil..
from Indonesian like 👍👍👍
Great for mascerating the crap outta a covercrop before tarping using a bit higher & lighter touch so as not to disturb too much soil...like a power harrow set on the highest setting.
Is it even tilling the actual ground?
I can't tell but it looks like it's just getting rid of the weeds...which is great...but didn't it already do that?
Нагрузка на редуктор по-любому огромная они на это не предназначены.
Good job.
If you didn't want me to do this at home then you shouldn't have shown me this! I'm thinking longer bolts with less of them. Thanks.
I'm also thinking of using an old 7 1/4 inch saw blade with portions of the blade cut 2 to 3 inches from the outside edge towards the center and bent at 90 degrees.
Jody Smith
Картоху вместе с колорадом месить пойдет! Чтоб никаму не досталась!А идея заи.ись скора такой диск будет в стандартной комплекташке всех триммеров :попробовал -иди за новой косой!и в магазе менеджер будет впаривать:берите смелее у меня такойже 4 года.
Я так понимаю что " это" должно было избавить тебя от сарняка.Но это чудо не справилось с задачей ,оно просто срезало верхушки травы,и на следующей неделе она снова вырастет!Ну если ленишся полоть ,поставь леску 4-5мл. и скоси ,выйдет тоже самое ,даже лучше ,потому что трава не скосилась и она по-прежнему торчит .
Its good to share creative ideas bro and imma gonna do that for my garden too😆
Like for real.
Доктор Дю выехал за тобой.
Наша любимая сталь-пластилин 3🤣
Это не первый твой комент про доктора дю.РЖУ ПИЗДЕЦ
Кто доктор Дю, отзавись🙏🙏🙏
Just blowing soil away. It should work much slower than that and it would be a better tool.
Доработать напильником, будет мотоблок)))
This is not good ... only two wedges are enough !
Korek!!!... 👍♥️🙏
@dedamiloje6723
Tačno tako ploča je prevelika tj. prevelika rotirajuća masa što je opasno. Dvostruki nož iz prodavnice bolji i Sigurniji od ovoga....izgubljeno vreme za izradu....
Bom dia. Fiz 1:dessa mas coloquei uma proteção em volta do disco para não deixar a terra e outros objetos serem arremessados para longe e correr o risco de acidente com alguém próximo
Not good the roots still in the soil and the little stones will destroy your vegetables when they fly around
Excelente 👍
Зато рекламы нет! Лайк за это
Odličan patent.. Bravo
Thank you
Bravo majstore, kralj si .
TY for teaching me i do not want to try and build something like this
Need to watch that drill ! It will grab them headphones quick ! Not bad. But almost seemed like the regular weed whacker would do about as good. One big difference I noticed is you wouldn't have to constantly have to keep putting line on it ! ! Like you said if it was a bigger machine is think there would be better results with the garden clearing part. .
Great idea I need to try it
Людині немає чим зайнятись Ось і придумує всяку хрєнь. По другому цей апарат не назвеш.
Good job sir🙏
Скорей что долго коса не будет работать что-то сломает от вибрации
Парень, вот ты молодец. Сделаю себе такую же, а то жена между клумбами и грядками с тяпкой по полдня мучается.
см "плоскорез швабра"жена будет рада.
Muito bom!!!! (Very good!!!!, in portuguese)
Guglielmo, y
good job
To je dobra ideja, ali morate napraviti čvrstu podlogu (dno kante) kako ne bi došlo na sve strane
Ovaj metal je 2 mm i jako tesko ide na mom trimeru i predviđeno je za jace trimere ;) Ali dere ko ludo hahaha
Nice! Thanks.
;)
Interesting but dangerous i think.
А и зубы тоже жалко!!! Клубника с песком вкусная будет.....
You made a crop circle. 👽
Dust in the wind everything dust in the wind but really creative hi friends
Very nice job
лайк за трудолюбие,но!!! опасно такой инструмент использовать - выбрация на макс.оборотах наверняка бешеная + не дай БОГ гайка отлетит в кого ни будь......семь раз отмерь и один раз подумай правильно ли отмерил.......
Very heavy to they machine 12 pcs toot is ok
Doctor D.S. Now you must go and get your disc patented. And produce millions so you can make millions.
Dude I'm going to try and do the same thx
Это не земля,а осфальт какой-то!!! Между рядов положи сено или солому травы не будет и когда поливаеш обувь чистая!!!
Or you can spend $110 and less time and buy a tiller attatchment.. All in all good experiment. It would probably make a hell of a brush hog attatchment.
They dont make bushhog attachments for whips smart guy
Dobre! Molodez mujik!
Пока концовку смотрел ,аж пыль в зубах заскрипела.
It would make a helpful tools to make a fire brake when fighting fires 👌👋👋👋👍👍👍
To od zakrivljenih eksera
Doctor d s u r great I salute you sir
А смысл?косить леской проще.Понимаю если б он рыхлит землю.
А смысл? Есть плоскорез для этого, который много усилий не требует....
Hay guy , the in improvement you need to make is starting at one point use a use a 1/2 lainth screw 3 of them in the outer perimeter then move up 1 inch every set of three tell you get back to the first 1/2 screw then make a pie like shape ,,,,,, from the outer perimeter looking to the center of the disk place that size screw tell you reach the center of the disk , then place it on the weed eater ,,,,then add wait to the outer perimeter to balance the disk like a car tire weld them down so thay dont fly off
На луну, сажать алюминиевые огурцы!
Very nice