a set of 20 sent crimp connectors and some heat shrink tubing would make the wiring so much better. Electrical tape should be placed on top of heat shrink waterproof tubing. Good video - appreciate the hint on running the wire through the firewall - I went through the firewall by the brake pedal. Good to know alternative spot to run the wires.
The ground wire you placed on the toggle switch (gold prong) is what gets illumination of the switch. So it does matter what wire goes where on the other prongs. One will supply light to the toggle the other will not.
Seriously I like this video with the exception of all of the things I would’ve wanted to know the cameras pointing at your back the back of your T-shirt.
Nice! But when you were crimping the wires together you were supposed to crimp a male connector onto the lights instead of just sticking them in there. Great video though!
good informative video, that thing where you ran the cable under it's called the cowl. where did you place your switch? on the video the cable seemed to be short.
Do these interfere with the radio at all, I have used some inexpensive lights in the past and they stomp all over the AM radio stations and some hissing on FM. Just found your channel and love the vids!
Bro did you seriously crimp a female clam connector? Correct way is either crimp male connector to light or remove clam and use splice butt connector, then heat shrink to weather proof.
Conner Hayes I had a set for roughly a year and yes a little water got inside of them but the LEDs still worked and they were very bright for the price they are on amazon. Definitely more impressive than eBay lights that may even be more expensive.
If I get 2 of the 4 inch light bars do I need to get 2 separate wiring harness? Or is there a kit that allows you to hook both lights up? If so can someone point me to the harness I need? Getting 2 4inch Nilight 18w light bars thanks for any help
Hey man! I have been a subscriber for over a year now and I actually picked up my Jeep 2 days after I first saw your how to use the Jeep's 4x4 system. Well I just started making videos on it and I would love if you could check them out and give me some feed back!
Total hack job. Electrical tape is not going to stop water. Get a set of crimpers and some heat shrink. That was not a torque wrench it was a ratchet wrench. This hurt watch. I just wanted to see if the lights were any good
“This hurt watch”, that’s a hack job of the English language. Instead of criticizing my work, you should make your own channel. Then everyone can learn from the master.
I ordered these about 2yrs ago and their still work. they've been in the heat,rain,snow and mud and I have no issue with them.
What is the ground wire for. How does it work
a set of 20 sent crimp connectors and some heat shrink tubing would make the wiring so much better. Electrical tape should be placed on top of heat shrink waterproof tubing. Good video - appreciate the hint on running the wire through the firewall - I went through the firewall by the brake pedal. Good to know alternative spot to run the wires.
I just put this set up in my cart on Amazon but wanted to check RUclips first.Thanx for a great video,I’m going back to buy them now
The ground wire you placed on the toggle switch (gold prong) is what gets illumination of the switch. So it does matter what wire goes where on the other prongs. One will supply light to the toggle the other will not.
Great video! I personally prefer the four LED "cube" style lights for windshield mounting, but these are cool to!
Heat shrink works better for moisture protection
A little bit of a hack job on the wiring there. But a true Unity spotlight with LED is the way to go!
Why was he crimping the wires to a spade connection?
Hope he is not an electrician , would never pass codes. Lol
Seriously I like this video with the exception of all of the things I would’ve wanted to know the cameras pointing at your back the back of your T-shirt.
just got these off amazon for my canyon... thank you so much for this! helped me out real good
Should’ve had a camera over the battery to show the work
No wire hangers! lol So much easier with an Spod. Thanks for the video.
Would love to see if anyone has a video or advice on where to mount the brackets for these lights.
you didn't explain the wiring very well and you keep getting in the way of the camera hard to tell what you are doing .......
Gonna put these on my truck. Question, am I still gonna be safe to go through a car wash with these mounted on my hood?
Nice! But when you were crimping the wires together you were supposed to crimp a male connector onto the lights instead of just sticking them in there. Great video though!
Great video I’m gonna be putting them in tomorrow and this video helped
What did you screw it onto? I recently bought a Jeep and need that part that you attached the light to
Gracias eres el único que explica bien bro
SOLDER IT!!!!
Ur back! Glad to see! #jeepwave
+AdventureDex #jeepwave
very instructive and nice video!
So cool! Thanks Tom!
Good video🇺🇸
good informative video, that thing where you ran the cable under it's called the cowl. where did you place your switch? on the video the cable seemed to be short.
+Manuel Nuno right now I have it resting on the dash, I'm going to get a toggle post to organize my switches, and I'll post a video on that!
Do these interfere with the radio at all, I have used some inexpensive lights in the past and they stomp all over the AM radio stations and some hissing on FM. Just found your channel and love the vids!
+TAC C actually I did notice that, I mostly listen to satellite or play music through my phone and there isn't any interference but am yes
Thanks for the video it help me install mine👍
Where the hell do you put the relay that’s attached to the wire
Great video 👍
Is the install the same on a wrangler TJ?
Dammit I thought that black wire went to the negative battery terminal?
me too WTF?!?
For the Junction box is there anywhere specific it needs to be mounted, or just anywhere it will fit?
Is that a quick release for side mirrors on your light bar mounting bracket? Does the mirror hold in the highway and do they shake?
do u have to connect the black wire to the negative at the battery or can i just connect it to a bolt near the battery
Any thing that is grounded
very helpful video man
where are your videos? have you stopped
Does the relay need to be grounded or is the hole simply meant to be a mount?
If you don't have the light bar on top what do you mount these spotlights to?
You should quit smoking weed
How did you mount the switch?
Do u have a problem with wind noise with your big light bar
Where did you mount the switch in the dash? I ordered the one with the 5-pin rocker switch...
Bro did you seriously crimp a female clam connector? Correct way is either crimp male connector to light or remove clam and use splice butt connector, then heat shrink to weather proof.
Thats a relay not a junction box, also that's the smallest "torque wrench" I've ever seen.
have you had any trouble with water getting in? or the led burning out?
Conner Hayes I had a set for roughly a year and yes a little water got inside of them but the LEDs still worked and they were very bright for the price they are on amazon. Definitely more impressive than eBay lights that may even be more expensive.
A little silicone around the lens and cord stops that
You didn't mention that the instructions are very sketchy/to non existent
If I get 2 of the 4 inch light bars do I need to get 2 separate wiring harness? Or is there a kit that allows you to hook both lights up? If so can someone point me to the harness I need? Getting 2 4inch Nilight 18w light bars thanks for any help
mateo Chafin ive wired mine up to my existing headlight wiring harness just tapped in separate time and has worked fine for me ever sence
you can wire both to 1 switch i have 12 light bars on my truck and only have 5 switchd
Hey that’s not a torque wrench that’s a ratchet. Not trying to be rude at all
Torx it's a style of bolt
Hey man! I have been a subscriber for over a year now and I actually picked up my Jeep 2 days after I first saw your how to use the Jeep's 4x4 system. Well I just started making videos on it and I would love if you could check them out and give me some feed back!
Elliott Barcoe-Walsh absolutely, I'd love to! Good deal man!
Bud, you completely slaughtered that wiring job.....
At least wrap the tape tight so it's sealed lol
it sucks because only half the screen show the picture not my phone it's your phone learn how to use it
Gary King shut the hell up
Total hack job. Electrical tape is not going to stop water. Get a set of crimpers and some heat shrink. That was not a torque wrench it was a ratchet wrench. This hurt watch. I just wanted to see if the lights were any good
“This hurt watch”, that’s a hack job of the English language. Instead of criticizing my work, you should make your own channel. Then everyone can learn from the master.