Dodge / Chrysler FWD 2.4L Engine Removal.
HTML-код
- Опубликовано: 5 окт 2024
- After I remove the engine there is some footage of me replacing what I do on every engine installed, water pump, thermostat and spark plugs. At the very end is just me mating them back together as well. Enjoy! More to come as always.
![[Limbus Company - PV] Chapter.7 - Oblivion](http://i.ytimg.com/vi/VUpkXPkvoxU/mqdefault.jpg)
This video is pure gold.
I was thinking of doing a bottom rebuild(Main Bearings/ Crankshaft ect) on my 2.0 on my 07 caliber because my camshaft is knocking (I think it’s the barrings ) and now I’m thinking a swap may end up being a better option since it’s a very similar engine style and seems pretty straightforward .
These videos are not only well presented but also informative in a way words cannot explain big thanks man. 🤟🏽
With most of the chrysler engines wr run into the rockers wearing into the cam. You can just swap rollers if you can press the valve spring down. Make sure the keepers and valve go down or you could be in deep water. But if you were going to remove the head anyways ignore me lol.
Happy my videos can help.
Video got me walking around like the man In my engine class now 😂😂
Your hands tigjty clasped behind your back as you quietly walk around and letting the class which machine is must likely to be head them is
My trans just has gone out. I'm gonna remove it and rebuild it
Dude the video is on point you are an awesome tech
Thanks, my friend. This video helped me a lot 👍
Glad to hear that!
I have to change one of these motors for my daughter's car...it will be my first motor change even though I witnessed a few with 307's and 350's.... no lift though
You shouldn't have a problem. Good luck!
@@CarMechaNick omw to LKQ today ...HFD....and it seems all I need is 10mm and 15mm...what should I bring?
Just bring a whole rack. Same with wrenches. I honestly can't remember if the crank bolt was extra large, like a 22 or something maybe. Bring a few big boys too. Just incase. Good luck man take plenty of water if you're in a hot area.
Thanks for sharing!
That's these videos help so much.
Great video bro !
Thanks!
Do you recommend a timing chain at this point or what are your thoughts on that in regards to labor? Should be fairly cheap labor since the engine is out but I see a lot of recommendations from the parts store that seems like a lot of money at the end for the customer. I usually do the water pump and belt if applicable but I would not do the chain. Thanks!
With these motors specifically we don't have many timing issues. If it were the Chevrolet 2.4L I would highly recommend it lol. Always a good idea to replace those other wear items like you said though. Water pump, thermostat, spark plugs, and if any leaks I'll reseal as well.
I would definitely give a discount on the labor for doing these timing jobs outside of the car. It is way easier and a prevention not necessity.
Thanks for watching!
Will be doing this on a 16 chrysler 200 soon. Any idea if new engine needs any sort of programming after installation?
How did you remove the transmission from the engine
Do you have to unplugg the anything to the Ac?
I need to changed lifters ..do I need to take the entire engine out ? Or it’s best to recommend taking it out ?
My sister has a 2011 with 130k blown motor . Wish I could replace it cheaply , not sure it’s worth it for the reliability.
i have a 2013 Chrysler 200 2.4l 4cyl with 170k and i dog the shit out of it everyday
Awesome video man! I have a question, I drive a 2012 dodge journey (base trim model) with the 2.4L 4-cylinder Dual VVT engine. And I have run in a few problems this past year, first with all the coolant hoses braking, the water pump had to be changed too, also the idler and tensioner pulleys had to be changed since they were squeaking and smelt like burnt. And now my question is: why does my car gives a gas odor when it reaches the speeds of 70 mph and up?
Do you have a leak? Yikes be careful!
If you want to ratchet up the suffering, replace this same engine in a Jeep Patriot. It's exponentially harder.
I’ll shoot a video and show you it’s not bad. I just bungee up the transfer case and pull them the same way.
Which vehicle is this specifically? Are most if not all dodge/Chrysler fwd vehicles like this? I'm on the fence of getting a remanufactured engine put into my 2005 Sebring.
do have to takes those off too 5:07?
Do whatever, if you can do it without go for it.
My 2010 avenger is ticking during cold starts it eventually quiets down, I was thinking it would be my lifter, any pointers on how to address this ?
You should have someone check it out. May be able to remove valve covers to find the issue, but would need someone experienced in the issue.
Is it possible to remove the engine of a dart without removing the transmission! Thanks!
Yup I've done those also.
How would i go about removing torque converter bolts if engine is seized
Take the pan off and free that bad boy up
How long did it take to remove the engine?
These are gravy, takes a few hours.
Done watched this 2 times I think I’m ready🫡😎
It’s nothing you got this!
Question I have 2013 dodge dart 2.0 manual 6 speed can I put a 2.4 in replace it looks like everything bolts up just not sure if I need a donor car if I have to replace every wire and computer any help would be appreciated and I busted a connecting rod sucked up to much water
I honestly have no idea. If it were a Honda I could answer that question lol.
Which would you say it's more labor intensive? Taking an engine out, or putting it back in?
It's probably more putting in, just because you have to line them up right before you assemble.
Putting it back in cause you better remember where those connections wires go
What transmission make model is it
Can you pull the transmission from the top?
I never have but I hear ppl do it with some cars.
Hey Nick, I'm from Canada 🇨🇦 Alberta and I got a 2012 Dodge journey with a seized engine. Is it possible to do an engine swap without changing the ECU? I plan to swap the engine myself a collage kid with basic understanding of cars
You sure can. I would clean and use your old throttle body.
@@CarMechaNick Hey, 2.4L Engine is Seized. Do you have any Techniques that will be able to turn the crank so that I can unscrew the flywheel bolts?
Your best bet is to remove the pan, then start by just loosening rod and crank caps. You may be able to spin after releasing pressure. May have to hit spots with a hammer and such.
Hey I have a 2014 2.4 that needs an engine
What you charge for replacing an engine and why are you located
If you supply the engine it's 80 an hour for labor. Parts prices also vary so its best to call and get a quote at some local shops. Where are you located?
What brand is your air ratchet?
I have the matco, I think it was called reactionless or something weird like that.
Where are you located ?
I'm in Ohio
He farted at 6:09
a classic fart
Its crazy how many stupid questions are in these comments😂😂😂