If you ever doubted for one second that this is one of the best mechanics ever, this video should settle the debate. Epic stuff... How ever far that guy drove to get to the Master it was well worth the effort. I wonder how many people have used google maps from their home to Avoca NY, just in case... You Sir are a legend....
I have to visit Punxsutawney PA every now and then and sometimes I get the overwhelming urge to turn North and visit SMA. He probably gets bored real quick with people stopping by just to visit him.
He's an hour and 20 minutes from me. Too far for a regular mechanic, but if I ever have anything I really can't figure out, I'd consider making the trip.
I used to live in NY supervisor for the highway department and had to deal with snow and salt......I don't know how you do it, lol for the last 28 here in Florida repairing Ambulances and people say how do you do it. LOL you are a joy to watch stay safe. Tommy
With solid state test meters (in almost all cases) even the continuity test, let alone the resistance ranges, is *polarized*! If you just have a circuit being tested that is resistive in value, it doesn't matter (with rare exceptions, caps and other components can throw that off) but if there are semiconductors (diodes, control modules, solid state relays, LED lights, etc) in the circuit, you might see a short tested one way, and an open circuit the other, and everything in-between. When in doubt, flip your leads around. I'm an electronic tech, and the more expensive meters are self polarizing for voltage checks, but when testing continuity/resistance, habit alone says to flip the leads if a reading is odd. You're absolutely right to query what your meter is telling you until you've addressed a number of quirks. I note the drive motor had a 'clamp' across it, two diodes in series, one shown in the schematic as a straight diode, and the other as a zener. Again, especially if the clamping voltage is exceeded by a tester (rare, dependent on a couple of factors) you'll get a puzzling reading. However, if the zener is shorted, and the motor is open, you'll be reading the forward resistance of the regular diode one way, and an open circuit the other. Your using an incandescent bulb addresses many of those false indications. Sometimes simple tells the best truth. Btw: Your logic is superlative. I've complimented you a few times over the years. Electrical logic can be hard for many mechanics, even really good ones, but for some like yourself, it comes naturally.
I used to manufacture LEDs and Long Island City New York about 1979 80 and the bottom line is LEDs only allow a flow of electricity one way and to wire them up in series like I did for Halloween in my hat it's interesting you got to get your circuits right and you voltage right and don't work great forever hey have a good day
Watching you struggle to get into tight areas, I am reminded of watching my dad trying to get his large hands into spaces like that. He had scars on the backs of his hands and on his arms and the day we buried him, he had a 3 inch cut on the back of his right hand. I have such respect for what he went through to feed and clothe his family. Eric you are a rockstar.
You can’t be a mechanic and not have scarred hands. After 40 years of wrenching my hands carry quite a few. My father played accordion for living and because he liked working on his cars his were hacked up too.
My old man was similar. I learned how to rebuild a carb at a young age because my dad's sausage fingers couldn't hold the jets. Learned that and many others things due to being only 10 ish and having small enough hands and arms to get into those tight spaces. Lastly I learned how to correctly cut off the extra from a zip tie so that you don't create a future scalpel in the engine compartment. That's a handy piece of information right there.
Every time I work on my truck I always ask myself "what would SMA also look at?" And every time I always fix so many more issues or find something that is about to break and fix it before hand. Love the content as always!!! Thank you!
@@RyanHull76 Visual inspection is the way to go. My friend called me over to his house, he is a mechanic. He has a 91 Camaro that is misfiring really badly. He had just replaced the plug wires and spark plugs. I look down the side of the engine and one of the spark plug wires is almost in 2 pieces. I can see the spark jumping across the gap. The wire had melted almost all the way through and it was amazing that it was still running like that. He was embarrassed because he thought it was primary ignition. "There's your problem, Lady!"
He is like Sherlock Holmes look at every thing before touching. Steve has done the most for me by getting me to slow down and stay calm. Found my first shorted wire a month ago by using my nose!
they worked great, until you didn't lock them before running off into deep mud/snow and then had to crawl around in it to lock them. the manual case was fine, but sheeple could never figure them out 😒
The first step in fixing a problem is knowing how it's suppose to work, and you have the experience and knowledge to do that. Considering all the different cars you work on and all the test equipment you need to know how to use it's amazing. And to know when a tool is lying to you is a really valuable skill. Another great video sir.
Imagine if doctor could not trust their MRIs or Xrays and now you see what a great mechanic is up against(not to mention there has only been 1 model of humans for quite a while) Yes I know humans do have differences but ...
@@MDAdams72668 I use to wonder why Mr O didn't trust All Data, then I subscribe to it to fix my '13 Dodge Dart. Yeah, I don't trust it more than I can throw it. It's a reference not an authority.
@@stevenrice47 All of them are accurate (sometimes) hence why I always had at least 3 "books" usually if 2 of three agreed it would be correct LOL same with scan tools(maybe not quite as bad but close) and add to that the newer cars "substituting values" and it is a real cluster Does not matter how "good" you are if the info you are given is crap the results will show it It's even worse with the newer vehicles because you cannot truly "read" the bus so you have to rely(at least in part) on someone else's software
You've been killing it with the videos these last couple of weeks - I just wanted to let you know I appreciate the content and the entertainment, and I'm sure I speak for countless others when I say that.
I had a 75 blazer with four speed with Granny gear and a floor shift for the transfer case if you were in a tight pinch just kicker in the four-wheel drive and double clutch and you're ready to go have a great day
@@agger838 not some day soon..... mine is 45 years old and still works the lever that is......when your is 45 That's true test but most don't keep a truck past 10 years lol 😆
My neighbor said someone vandalized her 20something rustbucket pickup by reaching in and snapping off the 4WD lever overnight. (The 4WD hadn't worked in years anyway.) The broken face had a single spark of bright metal, and the rest was old, deep crusty rust. I believe it was 99% cracked through for years, and finally gave up the ghost that night.
Eric, you probably have already found this, or already know this, but from the Power Probe IV manual - "LED, Green (-) - Will light indicating a path to ground. More than10Ω resistance and/ or more than 0.5 volts on a ground circuit, the Green LED will not illuminate. Additionally, from the Power Probe IV manual - "This greatly simplifies testing as the Power Probe IV’s Red/Green LEDs and speaker tones provide a quick indication if there are excessive voltage drops or circuit resistance. If the LEDs do not illuminate and there is no tone from the speaker, you know instantly there may be a circuit problem." In short, the Power Probe IV gave exactly what it should have, indicating a circuit problem because the Green LED did not light and the Buzzer did not sound. It indicated the solenoid is open, as it was. On the new solenoid the Power Probe IV gave the correct resistance. Great video, as usual though. Your videos are greatly appreciated and we thank you. They are also the best on RUclips, bar none. You are the best mechanic, diagnostician I have had any kind of experience with in 50 years, especially with electrical stuff, which I have found is most every mechanics weakest skill. You are the rare exception. You are also very good with making the videos. Again, great job and thanks. Omegaman
The problem was that Mr. O checked the path to ground through the control board and even though the control board was indeed providing a ground the power probe did not indicate a valid ground. This is most likely the result of resistance in the ground path through the control board.
I have the same kind of phones with the same ring. When the phone rang my wife hollered from the other room, "Will you get it." I hollered back, "No worry. Mrs. O will get it." She said, "What?!"
Love the Big Clive reference at the end there LOL I went to a shop to have a clunking noise in my 06 Ford Territory diagnosed, it has 300,00km on the clock (186,000 miles for you backwards folk), and they told me it was the control arm ball joints in the front left wheel arch. Lucky for me they're a part with two bolts so I ordered one off of eBay and fitted it myself (thanks to you, Eric, for giving me the confidence to work on my own car) but it didn't fix the problem... so I just kept driving it until it really pissed me off oneday and I got under the car when it was stationary and figured out that it was the sway bar D rubbers that were allowing the bar to jump when I cornered causing a clunking sound... Now I try and diagnose the issues myself before taking it to a mechanic. The situation in this video is the path I was headed down when they told me it was the ball joint, was gonna start replacing parts till I found the right one. You're a legend Eric, and Mrs. O.
I wonder if other shops watch your videos and think to themselves, "man we gotta do better" or if they just brush it off and continue hanging parts... Good video as always.
@@roeaaron974 I don't think it's dishonesty, unless it's dishonesty about their skill level. I don't believe the majority of shops are out to screw people intentionally, they just simply don't have the diagnostic skills or maybe motivation to do the testing.
And THIS is why Eric O is better than service data. Ive owned tons of GMT800 trucks and never knew where thr TCCM was. But thanks to his videos, i now know. Thank you Eric O. Best mechanic ever
Most times it can be like that. Cause & effect ! motor shorts out , fries module ! cause & effect. Engine looses all coolant & Engine Seizes up. Cause & effect. Allways Look for what causes something or it happens again.
Thank you for doing more diagnostic work I'm a pretty good diag guy you see a lot of stuff in the Rust Belt switch throws holding other curve has helped me out so much
The moral of the story is that where every you live you gotta find the guy in a shop who is a Dr. House guy who only cares about finding the source and fixing it... I am sure you got the reward and satisfaction you were looking for and it is so kind of you to share your success for our entertainment.
Nice job sir! Your videos are awesome! As a beginner tech in my second shop I look forward to watching this channel. I've been very encouraged by a few people to follow my dream and learn all I can and you've helped as well with your closing statements. Thank you.
Its all too easy to forget that you can get 2 faults in the same area, and they can happen at the same time. Thats why your methodical approach is so good.
Just an fyi from an electronics guy, solid-state components such as transistors and solid-state relays will mess with a multi-meter's ability to read resistance and continuity. Voltage and power measurements (as you did with the test light) are the only way to go. I enjoy your channels as well as Ray's as you guys go through the entire diagnostic process.
Power probe isn't a real multimeter and no, you're wrong, a high impedance multimeter and/or oscilloscope are the ONLY way to properly test a solid state circuit.
If it's pulse with modulating that circuit that's probably what screwed with his Power probe! I'm pretty sure you could actually hear it doing exactly that when he was shifting it and he was underneath the truck it sounded like a solenoid buzzing almost like you'd hear if it was on AC mains voltage but only while it was shifting.....
Osxilloscopes read voltage vs time, not resistance and yes, semiconductor components will effect the ability of a meter to properly read resistance. The only semicondutor component a meter can test is a diode, and that is in continuity mode and with the probes in the correct polarity. Ij the case of a sinking circuit, that is, on that is switched to ground, a resistance or continuity check will not work if it is using a solid-state relay to do the switching. Don,t believe me, buy an SSR, and read the resistance across it in both the open and closed states
@@JosephArata Solid state components usually have some leakage and don’t fully switch off. A multimeter is such high resistance it doesn’t pull enough current for the leakage to disappear. So, it can get funky readings that aren’t true. The power probe is a simple multimeter made for 12v. The one he has can do more than the standard one that basically just shows voltage along with supplying power or ground.
heres an fyi, from a dumb ass,,what shts first in electronics.................mosphet... ... lights in fridges , micro waves,, fuse. how many been thrown away for a bulb..im still trying to find the fuse in the missus..
It just shows how your reputation has spread far and wide that a guy who is being robbed by the parts cannon thinks, nah, I'm going to see Eric O, he will find the problem and fix only what needs fixing without using the parts cannon. If I lived within 500 miles I'd be there for all my service and repair needs. Kudos Mr O. Now you have another customer for life through the power of RUclips. What I really love is that you will talk us through the fault, prove the fault by your own logic and explain it all at my low level of understanding of all things mechanical/electrical how, and why, then fix it. Excellent video, well worth the watch. Thank you.
You, Wes, & the Rainman are some of the few good mechanics left! These days, at most places it's all about firing the ole parts cannon & hope for the bestest, because the scan tool said it was faulty. Too many places have forgot how to do some ole fashioned trouble shooting to figure out WHY scan tool said part was inoperable, EVEN after they tried replacing it!
problem is the public thinks that mechanics (techs) should be willing to work for less than other techs despite working in dirty cold or hot environments If you have the intelligence to do quality diag and are willing to be underpaid you are Mr. O (or me for years) But at some point we only do the "unfixable" and get paid right to do it. I won't even look for less than 125/hr
I hate to say it you know Eric does a great job using technology but also he uses a lot of logic and common Sense some people just depend on technology totally and don't even really think about the problem at hand and how to diagnose it have a good day
Excellent point about using test equipment. I use the power point you gave me for providing power or grounds when testing circuits and it works perfectly for that. I keep it simple that's for sure. Really good video Eric. Your impression of the solenoid working was spot on! Made me laugh.
Thanks so much for making these videos. I used to be very timid in attempting my own auto repairs but with the help of these videos I am becoming more confident in tackling some of these repairs myself. It has helped our family out to save some money when things are a little tight.
gotta love the local U-pick yards. There's one about 5 miles from my house and they usually have 1,200 cars in their yard. They've saved me a ton of money.
Chipmunks got in my 2008 Chevy truck and peed on fuses. Started it one morning and instrument cluster lit up like a Christmas tree. Great job troubleshooting. Love watching.
27:28 You fixed it so well that the fire siren went off 😂. For a NY second I thought "Damn, that's a noisy transfer case motor". As always, great video. Impressed with your through and logical diagnostics
Thing is in certain areas engineers in the infinite wisdom and introduced electronics instead of leaving things simple and mechanical using plain old switches or mechanical controls I don't get it or does it create more points for failure and this wonderful world of ours have a great day
Amazing somebody with troubleshooting skills. In the last 50 years I have seen so many people in the trades turn into parts changers. The trade schools must not seem to teach techs how to truly diagnose problems. Or they just don't want to take the time. Just replace parts until they possibly hit on the bad part. Damn fine job that you did you are a master.
It is funny. When Eric was removing the control module I was saying to myself, GET THE CONTROL PANEL! Those come in handy so many times. Plus I am a hoarder.
It’s too bad that all the instructors at trade schools can’t be as good as you man. You make it so much easier to learn I’ve learned so much about automotive in the 5 years I’ve been watching you. Anyone who freely passed their knowledge on to others is ok in my book man
You have the patience of an angel. Trucks need to work ,too many wires to call this a reliable design. Glad to see you got this fixed. Frustration pay?
Love watching your evidence based approach to fixing car and truck problems, Eric. Trust nothing without separate sourced confirmation, even your own equipment. I suppose that after many years of wrenching, you learn to maintain a sense of humour when the issue would try the patience of a saint! Your clients are very lucky to have you to turn to, one of the best things a car owner can find is a car mechanic that you can be trusted unquestioningly to do the right thing. You are one of those guys. I have expressed this before in a comment, but is a damn shame that you are not involved in the training of both new and experienced motor mechanics. They could learn a lot from you. Best wishes from Australia.
Got to love the older GM products. This one was perfect for diag making sense. Of course when they get older, the plastics do get brittle and gentle hands are a complete requirement or else the customers parts are going to get damaged...something a lot of mechanics need to pay attention to more mainly because even though the vehicle is old...lots of folks put a lot of value in them because they are more dependable and problem free than the newer crap. This first thing I tell a shop before I let them work on it is, "it's older, can you please take your time and be carefull with the plastics"? Some of those parts are non existent. You might have earned a new customer on this repair !
That's one of the biggest problem with some of the aging vehicles the plastic gets brittle part of the problem is they change the chemical composition of the plastics to make it cheaper also in the molding process there are Gates that run plastic to the parts themselves they regrind the plastic that's already been heated through heat cycles and grind it back into the new plastic pellets the problem is it makes the plastic brittle not a good idea but they can save a little money and they don't care what the end user ends up with have a great day
I sure miss that lever sticking through the floor. It was so much simpler. Great job, as usual. I watch your videos like i read a gppd book. The plot changes, and then the AHA moment. Another mystery solved.
Did this repair on my 05 yukon. Mine I took that apart, replaced the part inside that unit to make the transfer case work properly again. Yes it's easier to pull the entire shaft. Love the videos. Range position sensor was my issue.
Good video, fun to watch. Richard and Theresa at Precision Transmission had the virus in Jan., of course they are both better. Theresa does the filming of Richard pulling the trans apart. Well, she has her smelling back, but Richard does not. It's funny because when he gets one of those smelly trans apart, Theresa can not hardly stand it while Richard is standing over the trans and can not smell a thing. Funny, because you mentioned you have not gotten your smell back. I guess in some trades it's better not to have your smell!!!!!!! lol
I'm just glad there's people honest like you that will tell people the right diagnosis it's unfortunate people just want to rip you off and cell you parts that you don't need I've been watching you now for years I live in Massachusetts and a lot of salt appear I'm glad you do a lot of breaks and other parts that you can show people like me what to do with rusted parts and how to get them off thank you so much keep up the good work I will be watching you every time you send one out
There is also a flip side to that. A lot of people aren’t willing to pay for a diagnosis. Which as any of us in the industry know and also any consumers/diy people who follow sma know is the most important part but a lot of people try and bypass this part
@@Enrightauto as a DIYer/enthusiast…. The most important thing I’ve learned is to know my limits… secondly there’s always more to learn… I’ll do many things on my own vehicle a lot have no clue about. But there’s still tons of stuff I don’t know enough about or don’t have the tools/experience to get involved with. The great news is I have an honest local mechanic who is always there when I hit my limits… and he’s worth every cent and more!
The method you used to align the motor shaft-jogging the motor with the scan tool and immediately pulling the plug-was pure genius and something I wouldn’t have thought of in a million years. That’s why I don’t think your parting words, “Remember, if I can do it, you can do it”, don’t apply in this case. However, it has inspired me to try harder to reach outside the box in my own difficult mechanical situations. Too bad the owner didn’t bring his truck to you to begin with…
As someone who takes my 2017 Chevy to the dealer frequently (warranty almost gone) I am thankful the world has legends like yourself with the knowledge to fix these issues. Love the videos and appreciate someone who can show off their problem solving skills on camera. Respect, a 2017 Silverado owner with a busted tail light and who knows what else! I’m across the country from you but I’d move in the blink of an eye if I could!
Thank you for making this. Extremely helpful. You REALLY know your stuff. Your diagnostic's and teaching ability are first rate. If you ever decide to offer tech classes I will be there.
I have known many mechanics over the years that own all the new gadgets, but very few that know how to use them. You do and thank you for sharing your knowledge with us.
Amazing camera skills! You the man! Thanks for sharing! Makes me appreciate my 2006 F150 4x4 with the old shifter handle on the floor that always works and a 99 cherokee. pull the handle and go! Sad the complexity engineered into some things for negligible benefit
ill take mechanical simplicity over electronics for reliability any day ! Especially under a truck , Exposed to the Elements & possibly underwater at times. Motors & wiring underwater , not advisable ! manual linkage Ftw !
I've been binging on you, Eric O. along with Ivan and Rainman Ray. I may have made a mistake. Now at age 73, I want to work on cars. After replacing a battery, my next challenge will be spark plugs and flush a radiator. I can buy a few extra tools and do basic stuff way cheaper than a dealership or garage. Maybe a low cost basic scanner is in my future. THANKS for all the help.
You are the MAN Mr O. Always educating with great knowledge and simplifying all those complicated situations that the normal everyday guy goes through.thanks
There is a kit to eliminate all 4×4 servos ,modules etc. A Cable engagement kit for front axel and transfer case. I converted two older GMCs and suburbans made my own kit using boat shift cables.. Nice work.
You are the first auto repair guy that I have seen on RUclips using the standard troubleshooting techniques that I do. I was trained in electronic/electrical repair for sound systems. Trusting your test equipment by using it enough to understand it... most auto repair guys nowadays seem to just scan it, throw some parts at it, scan it throw more parts at it. Rinse Repeat. It makes the high priced vehicles we are running now SO much more expensive to repair. Also creates a bad working relationship, caused by the high $$$ and the variance of skill in the repair industry. And, honestly, I really like to KNOW what I am working on is doing what it was designed to do, AND how it does it. Kudos, SIR! Michael in Colorado.
Words can't express how much I thoroughly dislike board mounted relays. After having a few vehicles over the last ten years with them, I sold them all and went back to a 1998 Dodge Ram, because apparently I prefer screwing with broken vacuum lines and plastic dashes more than those mounted relays.
I appreciate how you take such professionalism in your trade. I work on my own stuff because I am pretty thorough and feel I work with care. I would have never figured that out. I wish I had a place around my area I trust to do the work you do!
It's good to know there are still skilled Mechanics out there that don't rip you off,fix what needs to be fixed,Thanks friend for the great videos,New Subscriber for sure!!!
Great to hear a shoutout to BigClive. Maybe send it over to him to inspect it? Would be fun to see a deepdive from him on this stuff. Great video as always. I bet if this fella who owns the truck wouldn't live so far away, he would be a regular customer now. Or maybe he takes the drive and stays with you. I'm always intrigued on how to diagnose these issues. Gives me as a regular customer that isn't working on his own car more appreciation for the labor that goes into this work. Keep up the great work! Cheers,
I'm literally dealing with the exact same issue on my dad's 02 Avalanche. Your video is right on time. I don't have a scanner, so, thoughts and prayers lol
My 2002 1500 Needed one of these modules. I always assumed it was the electrolytic capacitor that went bad because lots of electronics from this year had bad caps. It was called the capacitor plague and lasted until 2007.
Q515(near the B) look suspicious at 42:35, the solder is darker around it, if it's the case then a shorted mosfet could be the cause Edit: well you pointed it, I can smeel it through the screen the electronics burn smell! when a fet fail it could damage other circuit that control it, so yeah the module might be fixable but you need to clean the board, replace the fet, test it apply, conformal coating and done. it's best case scenario...
Excellent work. Seems like newer techs need to learn the old ways of checking failures, and the solution. Just following a checklist definitely doesn't always work. I worked in electronics for about 40 years, and the same is true in that profession. And the engineers definitely don't have all the answers because they don't have the hands-on experience. I could tell you some good stories about that. Keep up the good work.
Use the term resistance not impedance. Impedance is used in AC circuits not DC circuits. Love your video. It gives me new respect for competent mechanics.
All you have to is, lock it 4WD, turn the steering wheel sharp and give it some gas. If, the vehicle crabs/rocks side to side, it's in 4WD. You, can do that anywhere.🙂
I just watched this, really enjoyable. This is the way I work, trying to actually understand how the system works so I can logically work my way back through it. Sad fact, here in the UK the old days of going to the junk yard and pulling your own used parts seem to be over. Health and safety apparently ☹️ I can remember first finding the delights of the junk yard with my brother, messing around while my dad and uncles pulled parts to fix their cars, a tradition I chose to carry on. Happily my Land Rover Discovery still has a lever and cable to the transfer box to shift between high and low. Permanent four wheel drive on Disco 2s 😊
Do you ever get paranoid that someone is looking over you shoulder. I'm one of those people that need to see or touch to learn, you always teach me first time. Thank you
If you ever doubted for one second that this is one of the best mechanics ever, this video should settle the debate. Epic stuff... How ever far that guy drove to get to the Master it was well worth the effort. I wonder how many people have used google maps from their home to Avoca NY, just in case... You Sir are a legend....
Agreed. One thing that shows that is that he makes it look so easy...
@@tommost1 Experience does that.
@@tabbott429 Tru dat
I have to visit Punxsutawney PA every now and then and sometimes I get the overwhelming urge to turn North and visit SMA. He probably gets bored real quick with people stopping by just to visit him.
He's an hour and 20 minutes from me. Too far for a regular mechanic, but if I ever have anything I really can't figure out, I'd consider making the trip.
best line of the night numbers match now you can still go to the car show😂😂😂
I'm a mechanic for 50 years you are outstanding!! They are very lucky to have you!!
I used to live in NY supervisor for the highway department and had to deal with snow and salt......I don't know how you do it, lol for the last 28 here in Florida repairing Ambulances and people say how do you do it. LOL you are a joy to watch stay safe. Tommy
the owner was smart enough to not let the other shop split the transfer case. and lucky to have only a long drive to SMA for the real fix.
With solid state test meters (in almost all cases) even the continuity test, let alone the resistance ranges, is *polarized*! If you just have a circuit being tested that is resistive in value, it doesn't matter (with rare exceptions, caps and other components can throw that off) but if there are semiconductors (diodes, control modules, solid state relays, LED lights, etc) in the circuit, you might see a short tested one way, and an open circuit the other, and everything in-between.
When in doubt, flip your leads around. I'm an electronic tech, and the more expensive meters are self polarizing for voltage checks, but when testing continuity/resistance, habit alone says to flip the leads if a reading is odd.
You're absolutely right to query what your meter is telling you until you've addressed a number of quirks. I note the drive motor had a 'clamp' across it, two diodes in series, one shown in the schematic as a straight diode, and the other as a zener. Again, especially if the clamping voltage is exceeded by a tester (rare, dependent on a couple of factors) you'll get a puzzling reading. However, if the zener is shorted, and the motor is open, you'll be reading the forward resistance of the regular diode one way, and an open circuit the other.
Your using an incandescent bulb addresses many of those false indications. Sometimes simple tells the best truth.
Btw: Your logic is superlative. I've complimented you a few times over the years. Electrical logic can be hard for many mechanics, even really good ones, but for some like yourself, it comes naturally.
Good info here thanks for sharing!
I used to manufacture LEDs and Long Island City New York about 1979 80 and the bottom line is LEDs only allow a flow of electricity one way and to wire them up in series like I did for Halloween in my hat it's interesting you got to get your circuits right and you voltage right and don't work great forever hey have a good day
Watching you struggle to get into tight areas, I am reminded of watching my dad trying to get his large hands into spaces like that. He had scars on the backs of his hands and on his arms and the day we buried him, he had a 3 inch cut on the back of his right hand. I have such respect for what he went through to feed and clothe his family. Eric you are a rockstar.
My dad was the same way no I am getting like that
You can’t be a mechanic and not have scarred hands. After 40 years of wrenching my hands carry quite a few. My father played accordion for living and because he liked working on his cars his were hacked up too.
My old man was similar. I learned how to rebuild a carb at a young age because my dad's sausage fingers couldn't hold the jets. Learned that and many others things due to being only 10 ish and having small enough hands and arms to get into those tight spaces.
Lastly I learned how to correctly cut off the extra from a zip tie so that you don't create a future scalpel in the engine compartment. That's a handy piece of information right there.
Every time I work on my truck I always ask myself "what would SMA also look at?" And every time I always fix so many more issues or find something that is about to break and fix it before hand. Love the content as always!!! Thank you!
Since I started watching his videos... Visual Inspection. Every time... Has saved me unknown hours of poke and pray.
@@RyanHull76 Visual inspection is the way to go. My friend called me over to his house, he is a mechanic. He has a 91 Camaro that is misfiring really badly. He had just replaced the plug wires and spark plugs. I look down the side of the engine and one of the spark plug wires is almost in 2 pieces. I can see the spark jumping across the gap. The wire had melted almost all the way through and it was amazing that it was still running like that. He was embarrassed because he thought it was primary ignition. "There's your problem, Lady!"
He is like Sherlock Holmes look at every thing before touching. Steve has done the most for me by getting me to slow down and stay calm. Found my first shorted wire a month ago by using my nose!
Do you have a brother.
I like the levers and the manual hub locks. They just worked.
they worked great, until you didn't lock them before running off into deep mud/snow and then had to crawl around in it to lock them. the manual case was fine, but sheeple could never figure them out 😒
I had a 75 blazer with lockout 4 on the floor and a Cranford case it was bulletproof have a great day
The first step in fixing a problem is knowing how it's suppose to work, and you have the experience and knowledge to do that. Considering all the different cars you work on and all the test equipment you need to know how to use it's amazing. And to know when a tool is lying to you is a really valuable skill. Another great video sir.
the second step seems to be drive it on the south main test snow to fix any lingering little niggles 😁
It's impossible to fully fix something if you don't know how it's suppose to work. Somebody could half-ass it into an semi-operational state.
Imagine if doctor could not trust their MRIs or Xrays and now you see what a great mechanic is up against(not to mention there has only been 1 model of humans for quite a while) Yes I know humans do have differences but ...
@@MDAdams72668 I use to wonder why Mr O didn't trust All Data, then I subscribe to it to fix my '13 Dodge Dart. Yeah, I don't trust it more than I can throw it. It's a reference not an authority.
@@stevenrice47 All of them are accurate (sometimes) hence why I always had at least 3 "books" usually if 2 of three agreed it would be correct LOL same with scan tools(maybe not quite as bad but close) and add to that the newer cars "substituting values" and it is a real cluster Does not matter how "good" you are if the info you are given is crap the results will show it It's even worse with the newer vehicles because you cannot truly "read" the bus so you have to rely(at least in part) on someone else's software
Maybe these customers will keep the word of mouth going. You are honest and have a good personality and a sense of humor. You are a rarity.
You've been killing it with the videos these last couple of weeks - I just wanted to let you know I appreciate the content and the entertainment, and I'm sure I speak for countless others when I say that.
I had a 75 blazer with four speed with Granny gear and a floor shift for the transfer case if you were in a tight pinch just kicker in the four-wheel drive and double clutch and you're ready to go have a great day
The lever on the floor of my truck has never thrown a code and it always works.
I can say the same about my electric 4wd lol
@@agger838 not some day soon..... mine is 45 years old and still works the lever that is......when your is 45 That's true test but most don't keep a truck past 10 years lol 😆
My neighbor said someone vandalized her 20something rustbucket pickup by reaching in and snapping off the 4WD lever overnight. (The 4WD hadn't worked in years anyway.) The broken face had a single spark of bright metal, and the rest was old, deep crusty rust. I believe it was 99% cracked through for years, and finally gave up the ghost that night.
@@moparnut6286 shift linkages do break and rust tho
@@DaddyBeanDaddyBeanso sad to see such bad manitence on a classic truck lol 😆
Eric, you probably have already found this, or already know this, but from the Power Probe IV manual - "LED, Green (-) - Will light indicating a path
to ground. More than10Ω resistance and/
or more than 0.5 volts on a ground circuit,
the Green LED will not illuminate.
Additionally, from the Power Probe IV manual - "This greatly simplifies testing as the Power Probe IV’s Red/Green LEDs and speaker
tones provide a quick indication if there are excessive voltage drops or circuit
resistance. If the LEDs do not illuminate and there is no tone from the speaker, you
know instantly there may be a circuit problem."
In short, the Power Probe IV gave exactly what it should have, indicating a circuit problem because the Green LED did not light and the Buzzer did not sound. It indicated the solenoid is open, as it was. On the new solenoid the Power Probe IV gave the correct resistance.
Great video, as usual though. Your videos are greatly appreciated and we thank you. They are also the best on RUclips, bar none. You are the best mechanic, diagnostician I have had any kind of experience with in 50 years, especially with electrical stuff, which I have found is most every mechanics weakest skill. You are the rare exception. You are also very good with making the videos. Again, great job and thanks.
Omegaman
Top class omega man nice to see someone else with knowledge, greetings from Ireland
The problem was that Mr. O checked the path to ground through the control board and even though the control board was indeed providing a ground the power probe did not indicate a valid ground. This is most likely the result of resistance in the ground path through the control board.
@@johnmehaffey9953 Thank you for your complement. I appreciate it, greetings to you, and you have a great day.
Eric you're the real deal. Excellent troubleshooting.
I have the same kind of phones with the same ring.
When the phone rang my wife hollered from the other room, "Will you get it."
I hollered back, "No worry. Mrs. O will get it."
She said, "What?!"
Love the Big Clive reference at the end there LOL
I went to a shop to have a clunking noise in my 06 Ford Territory diagnosed, it has 300,00km on the clock (186,000 miles for you backwards folk), and they told me it was the control arm ball joints in the front left wheel arch. Lucky for me they're a part with two bolts so I ordered one off of eBay and fitted it myself (thanks to you, Eric, for giving me the confidence to work on my own car) but it didn't fix the problem... so I just kept driving it until it really pissed me off oneday and I got under the car when it was stationary and figured out that it was the sway bar D rubbers that were allowing the bar to jump when I cornered causing a clunking sound... Now I try and diagnose the issues myself before taking it to a mechanic. The situation in this video is the path I was headed down when they told me it was the ball joint, was gonna start replacing parts till I found the right one. You're a legend Eric, and Mrs. O.
Backwards ? Who are you, in England they buy liters and drive miles
@@quickturn66 I'm Australian, we buy litres, use dollars and measure in kilometres.
SMA is the best show in the town
I wonder if other shops watch your videos and think to themselves, "man we gotta do better" or if they just brush it off and continue hanging parts...
Good video as always.
If you find an honest auto tech hold on to them. They are rare.
@@roeaaron974 I don't think it's dishonesty, unless it's dishonesty about their skill level. I don't believe the majority of shops are out to screw people intentionally, they just simply don't have the diagnostic skills or maybe motivation to do the testing.
@@Pyro17059 most shops hire warm bodies.
Mr O has alot of time and money wrapped up in schools ,Tools and test equipment and a great wife who helps with everything.
I'm so glad that my Ram has a manual shifter for the transfer case!
Yessssssssssss. A 45 minute sma video. This is my yoga for the day!!! Haven’t watched it yet but I already know it’s good
And THIS is why Eric O is better than service data. Ive owned tons of GMT800 trucks and never knew where thr TCCM was. But thanks to his videos, i now know. Thank you Eric O. Best mechanic ever
Its always fun when you get multiple issues on the same repair
Most times it can be like that. Cause & effect !
motor shorts out , fries module ! cause & effect. Engine looses all coolant & Engine Seizes up. Cause & effect. Allways Look for what causes something or it happens again.
@@OcRefrig This is so true you would think their would be a system built in to prevent this
"Rule # 1 in a Chevy never roll the window down " Great line !
Thank you for doing more diagnostic work I'm a pretty good diag guy you see a lot of stuff in the Rust Belt switch throws holding other curve has helped me out so much
The moral of the story is that where every you live you gotta find the guy in a shop who is a Dr. House guy who only cares about finding the source and fixing it...
I am sure you got the reward and satisfaction you were looking for and it is so kind of you to share your success for our entertainment.
Nice job sir! Your videos are awesome! As a beginner tech in my second shop I look forward to watching this channel. I've been very encouraged by a few people to follow my dream and learn all I can and you've helped as well with your closing statements. Thank you.
Like how you understand how things work so you know what you're doing and why.
Great video Eric. Thank you As a retired heavy duty diesel tech I sure enjoy watching you unravel the electrical issues and get it fixed.
.....this is a true Classic....genius level work!!! You never give in....!!!!
A trip to the yard, hell yeah! Thanks Dr. O!
Its all too easy to forget that you can get 2 faults in the same area, and they can happen at the same time. Thats why your methodical approach is so good.
Just an fyi from an electronics guy, solid-state components such as transistors and solid-state relays will mess with a multi-meter's ability to read resistance and continuity. Voltage and power measurements (as you did with the test light) are the only way to go.
I enjoy your channels as well as Ray's as you guys go through the entire diagnostic process.
Power probe isn't a real multimeter and no, you're wrong, a high impedance multimeter and/or oscilloscope are the ONLY way to properly test a solid state circuit.
If it's pulse with modulating that circuit that's probably what screwed with his Power probe!
I'm pretty sure you could actually hear it doing exactly that when he was shifting it and he was underneath the truck it sounded like a solenoid buzzing almost like you'd hear if it was on AC mains voltage but only while it was shifting.....
Osxilloscopes read voltage vs time, not resistance and yes, semiconductor components will effect the ability of a meter to properly read resistance. The only semicondutor component a meter can test is a diode, and that is in continuity mode and with the probes in the correct polarity. Ij the case of a sinking circuit, that is, on that is switched to ground, a resistance or continuity check will not work if it is using a solid-state relay to do the switching.
Don,t believe me, buy an SSR, and read the resistance across it in both the open and closed states
@@JosephArata Solid state components usually have some leakage and don’t fully switch off. A multimeter is such high resistance it doesn’t pull enough current for the leakage to disappear. So, it can get funky readings that aren’t true.
The power probe is a simple multimeter made for 12v. The one he has can do more than the standard one that basically just shows voltage along with supplying power or ground.
heres an fyi, from a dumb ass,,what shts first in electronics.................mosphet... ... lights in fridges , micro waves,, fuse. how many been thrown away for a bulb..im still trying to find the fuse in the missus..
It just shows how your reputation has spread far and wide that a guy who is being robbed by the parts cannon thinks, nah, I'm going to see Eric O, he will find the problem and fix only what needs fixing without using the parts cannon. If I lived within 500 miles I'd be there for all my service and repair needs. Kudos Mr O. Now you have another customer for life through the power of RUclips. What I really love is that you will talk us through the fault, prove the fault by your own logic and explain it all at my low level of understanding of all things mechanical/electrical how, and why, then fix it. Excellent video, well worth the watch. Thank you.
Bonus SMA for the win!! Thanks as always, Eric!!
You still give the best explanations and allow viewers to actually see your work from start to finish. I'm old school and still pick up tips. Thanks
You, Wes, & the Rainman are some of the few good mechanics left!
These days, at most places it's all about firing the ole parts cannon & hope for the bestest, because the scan tool said it was faulty. Too many places have forgot how to do some ole fashioned trouble shooting to figure out WHY scan tool said part was inoperable, EVEN after they tried replacing it!
Following another "mechanic" is always a problem. That's why I always tell people im an automotive technician... Mechanics are parts changers.
problem is the public thinks that mechanics (techs) should be willing to work for less than other techs despite working in dirty cold or hot environments If you have the intelligence to do quality diag and are willing to be underpaid you are Mr. O (or me for years) But at some point we only do the "unfixable" and get paid right to do it. I won't even look for less than 125/hr
I hate to say it you know Eric does a great job using technology but also he uses a lot of logic and common Sense some people just depend on technology totally and don't even really think about the problem at hand and how to diagnose it have a good day
Funny as hell, logical troubleshooting path, double-triple verify your repairs, love the format. Thanks for the educational aspect and entertainment!
Excellent point about using test equipment. I use the power point you gave me for providing power or grounds when testing circuits and it works perfectly for that. I keep it simple that's for sure. Really good video Eric. Your impression of the solenoid working was spot on! Made me laugh.
Thanks so much for making these videos. I used to be very timid in attempting my own auto repairs but with the help of these videos I am becoming more confident in tackling some of these repairs myself. It has helped our family out to save some money when things are a little tight.
I was in the same position years ago but the weekend working on my truck so I could go back to work on Monday have a great day
gotta love the local U-pick yards. There's one about 5 miles from my house and they usually have 1,200 cars in their yard. They've saved me a ton of money.
Chipmunks got in my 2008 Chevy truck and peed on fuses. Started it one morning and instrument cluster lit up like a Christmas tree. Great job troubleshooting. Love watching.
The little bastards.
27:28 You fixed it so well that the fire siren went off 😂. For a NY second I thought "Damn, that's a noisy transfer case motor".
As always, great video. Impressed with your through and logical diagnostics
It confused me for a second when the siren went off just as he plugged in the module 😄.
Another mysterious case solved by Sherlock "O"!!! Awesome diagnosis. You are the man!
huge respect on figuring this out. I have always hated finding electrical issues, and this was a doozie.
Thing is in certain areas engineers in the infinite wisdom and introduced electronics instead of leaving things simple and mechanical using plain old switches or mechanical controls I don't get it or does it create more points for failure and this wonderful world of ours have a great day
Amazing somebody with troubleshooting skills. In the last 50 years I have seen so many people in the trades turn into parts changers. The trade schools must not seem to teach techs how to truly diagnose problems. Or they just don't want to take the time. Just replace parts until they possibly hit on the bad part. Damn fine job that you did you are a master.
You are unbelievable. Great job on finding and fixing this one.
It is funny. When Eric was removing the control module I was saying to myself, GET THE CONTROL PANEL! Those come in handy so many times. Plus I am a hoarder.
That thumbnail though .... love this channel and wish we had more like you around here! You're a freaking genius
Both are smashed.
I have a disease called PsA. It affects all of my nails and joints. That's the story :)
I loved that the Noon siren went off just as Eric O plugged in the replacement control module 😀
It’s too bad that all the instructors at trade schools can’t be as good as you man. You make it so much easier to learn I’ve learned so much about automotive in the 5 years I’ve been watching you. Anyone who freely passed their knowledge on to others is ok in my book man
Those that can't do teach have a good day
Mr "O" is pretty humble but his trouble shooting skills are excellent. Those folks that get their vehicles worked on get honest craftsmanship.
You have the patience of an angel. Trucks need to work ,too many wires to call this a reliable design. Glad to see you got this fixed. Frustration pay?
Love watching your evidence based approach to fixing car and truck problems, Eric. Trust nothing without separate sourced confirmation, even your own equipment. I suppose that after many years of wrenching, you learn to maintain a sense of humour when the issue would try the patience of a saint! Your clients are very lucky to have you to turn to, one of the best things a car owner can find is a car mechanic that you can be trusted unquestioningly to do the right thing. You are one of those guys. I have expressed this before in a comment, but is a damn shame that you are not involved in the training of both new and experienced motor mechanics. They could learn a lot from you. Best wishes from Australia.
Got to love the older GM products. This one was perfect for diag making sense. Of course when they get older, the plastics do get brittle and gentle hands are a complete requirement or else the customers parts are going to get damaged...something a lot of mechanics need to pay attention to more mainly because even though the vehicle is old...lots of folks put a lot of value in them because they are more dependable and problem free than the newer crap. This first thing I tell a shop before I let them work on it is, "it's older, can you please take your time and be carefull with the plastics"? Some of those parts are non existent.
You might have earned a new customer on this repair !
That's one of the biggest problem with some of the aging vehicles the plastic gets brittle part of the problem is they change the chemical composition of the plastics to make it cheaper also in the molding process there are Gates that run plastic to the parts themselves they regrind the plastic that's already been heated through heat cycles and grind it back into the new plastic pellets the problem is it makes the plastic brittle not a good idea but they can save a little money and they don't care what the end user ends up with have a great day
I sure miss that lever sticking through the floor. It was so much simpler. Great job, as usual. I watch your videos like i read a gppd book. The plot changes, and then the AHA moment. Another mystery solved.
Did this repair on my 05 yukon. Mine I took that apart, replaced the part inside that unit to make the transfer case work properly again. Yes it's easier to pull the entire shaft. Love the videos.
Range position sensor was my issue.
Your honesty by far exceeds any amount of knowledge or skill you think you lack. It’s very rare to find a honest mechanic these days
I like it when we get to go to the local pick-a-part
"Welcome to my TED talk"
I feel schooled every time I watch your videos. Thanks, Eric!!!
Good video, fun to watch. Richard and Theresa at Precision Transmission had the virus in Jan., of course they are both better. Theresa does the filming of Richard pulling the trans apart. Well, she has her smelling back, but Richard does not. It's funny because when he gets one of those smelly trans apart, Theresa can not hardly stand it while Richard is standing over the trans and can not smell a thing. Funny, because you mentioned you have not gotten your smell back. I guess in some trades it's better not to have your smell!!!!!!! lol
The funny thing about electronic components is that once you let the "smoke" out, they don't work anymore. Thanks for another great video.
I'm just glad there's people honest like you that will tell people the right diagnosis it's unfortunate people just want to rip you off and cell you parts that you don't need I've been watching you now for years I live in Massachusetts and a lot of salt appear I'm glad you do a lot of breaks and other parts that you can show people like me what to do with rusted parts and how to get them off thank you so much keep up the good work I will be watching you every time you send one out
There is also a flip side to that. A lot of people aren’t willing to pay for a diagnosis. Which as any of us in the industry know and also any consumers/diy people who follow sma know is the most important part but a lot of people try and bypass this part
I think this was more about ignorance than trying to rip someone off.
@@Enrightauto as a DIYer/enthusiast…. The most important thing I’ve learned is to know my limits… secondly there’s always more to learn… I’ll do many things on my own vehicle a lot have no clue about. But there’s still tons of stuff I don’t know enough about or don’t have the tools/experience to get involved with. The great news is I have an honest local mechanic who is always there when I hit my limits… and he’s worth every cent and more!
Yep mr O is not a parts changer he goes thru and finds out if its a normal wear and tear use or something else took out the part
The method you used to align the motor shaft-jogging the motor with the scan tool and immediately pulling the plug-was pure genius and something I wouldn’t have thought of in a million years. That’s why I don’t think your parting words, “Remember, if I can do it, you can do it”, don’t apply in this case. However, it has inspired me to try harder to reach outside the box in my own difficult mechanical situations. Too bad the owner didn’t bring his truck to you to begin with…
As someone who takes my 2017 Chevy to the dealer frequently (warranty almost gone) I am thankful the world has legends like yourself with the knowledge to fix these issues. Love the videos and appreciate someone who can show off their problem solving skills on camera. Respect, a 2017 Silverado owner with a busted tail light and who knows what else! I’m across the country from you but I’d move in the blink of an eye if I could!
Glad to see I'm not the only one who's thought seriously about hauling a vehicle your way from multiple states away.
Thank you for making this. Extremely helpful. You REALLY know your stuff. Your diagnostic's and teaching ability are first rate. If you ever decide to offer tech classes I will be there.
"It's always fun going to the junkyard." That is so damn true.
Hits a bump..."we even fixed the 2wd light"
I have known many mechanics over the years that own all the new gadgets, but very few that know how to use them. You do and thank you for sharing your knowledge with us.
Amazing camera skills! You the man! Thanks for sharing! Makes me appreciate my 2006 F150 4x4 with the old shifter handle on the floor that always works and a 99 cherokee. pull the handle and go! Sad the complexity engineered into some things for negligible benefit
ill take mechanical simplicity over electronics for reliability any day ! Especially under a truck , Exposed to the Elements & possibly underwater at times. Motors & wiring underwater , not advisable ! manual linkage Ftw !
I've been binging on you, Eric O. along with Ivan and Rainman Ray. I may have made a mistake. Now at age 73, I want to work on cars. After replacing a battery, my next challenge will be spark plugs and flush a radiator. I can buy a few extra tools and do basic stuff way cheaper than a dealership or garage. Maybe a low cost basic scanner is in my future. THANKS for all the help.
You've got the top three right there! Don't forget advanced level auto too!
Never too old to learn! Make sure you also check out Watch Wes Work...he's awesome too
Check out watch Wes work. Another great channel to binge watch
@@chrisfreemesser5707 Wes has a great mix of different equipment. Some stuff is a real doozy.
ScannerDanner
I don't do much work anymore at 71 but I sure like watching you.You're a very smart man!
Yet again....nothing short of amazing diagnostics! Simply can't get enough of your channel Mr. O. Great stuff!
You are the MAN Mr O.
Always educating with great knowledge and simplifying all those complicated situations that the normal everyday guy goes through.thanks
There is a kit to eliminate all 4×4 servos ,modules etc.
A Cable engagement kit for front axel and transfer case.
I converted two older GMCs and suburbans made my own kit using boat shift cables..
Nice work.
Makes me miss old school floor levers for 4x4
Love your videos it’s great to see someone that knows what they’re doing keep up the good work
You are the first auto repair guy that I have seen on RUclips using the standard troubleshooting techniques that I do. I was trained in electronic/electrical repair for sound systems. Trusting your test equipment by using it enough to understand it... most auto repair guys nowadays seem to just scan it, throw some parts at it, scan it throw more parts at it. Rinse Repeat. It makes the high priced vehicles we are running now SO much more expensive to repair. Also creates a bad working relationship, caused by the high $$$ and the variance of skill in the repair industry. And, honestly, I really like to KNOW what I am working on is doing what it was designed to do, AND how it does it. Kudos, SIR! Michael in Colorado.
So much new content from Eric and SMA - it's like Christmas!
The fact that Eric makes it look easy just shows what a master he is. Great work Eric.
Words can't express how much I thoroughly dislike board mounted relays. After having a few vehicles over the last ten years with them, I sold them all and went back to a 1998 Dodge Ram, because apparently I prefer screwing with broken vacuum lines and plastic dashes more than those mounted relays.
Great job, enjoy watching your program. I spent 50 years in the field the new stuff is very high tech. From Syracuse NY living in N C . Enjoy
I appreciate how you take such professionalism in your trade. I work on my own stuff because I am pretty thorough and feel I work with care. I would have never figured that out. I wish I had a place around my area I trust to do the work you do!
It's good to know there are still skilled Mechanics out there that don't rip you off,fix what needs to be fixed,Thanks friend for the great videos,New Subscriber for sure!!!
Great to hear a shoutout to BigClive. Maybe send it over to him to inspect it? Would be fun to see a deepdive from him on this stuff.
Great video as always. I bet if this fella who owns the truck wouldn't live so far away, he would be a regular customer now. Or maybe he takes the drive and stays with you.
I'm always intrigued on how to diagnose these issues. Gives me as a regular customer that isn't working on his own car more appreciation for the labor that goes into this work.
Keep up the great work!
Cheers,
Mr O you’re the very best, you never guess, just facts and then fix it proper.
I love how he can always take the last sentence and turn it into a request to go into the comment section...lol
Hey Erick, send the old part to Clive, I bet he’d love it.
I'm literally dealing with the exact same issue on my dad's 02 Avalanche. Your video is right on time. I don't have a scanner, so, thoughts and prayers lol
It took some detective work to find the problem, but You did it. Great job.
My 2002 1500 Needed one of these modules. I always assumed it was the electrolytic capacitor that went bad because lots of electronics from this year had bad caps. It was called the capacitor plague and lasted until 2007.
LOL "Whatever way I move it will be the wrong way and then we'll move it back in the right direction." SO TRUE !
Q515(near the B) look suspicious at 42:35, the solder is darker around it, if it's the case then a shorted mosfet could be the cause
Edit: well you pointed it, I can smeel it through the screen the electronics burn smell! when a fet fail it could damage other circuit that control it, so yeah the module might be fixable but you need to clean the board, replace the fet, test it apply, conformal coating and done. it's best case scenario...
Excellent work. Seems like newer techs need to learn the old ways of checking failures, and the solution. Just following a checklist definitely doesn't always work. I worked in electronics for about 40 years, and the same is true in that profession. And the engineers definitely don't have all the answers because they don't have the hands-on experience. I could tell you some good stories about that. Keep up the good work.
Me too
I'm just watching so I can hear Eric say "Chevrolaaay" ha ha!!
Don't forget it's got the (BIG) engine lol I love it
Use the term resistance not impedance. Impedance is used in AC circuits not DC circuits. Love your video. It gives me new respect for competent mechanics.
All you have to is, lock it 4WD, turn the steering wheel sharp and give it some gas. If, the vehicle crabs/rocks side to side, it's in 4WD. You, can do that anywhere.🙂
I just watched this, really enjoyable. This is the way I work, trying to actually understand how the system works so I can logically work my way back through it. Sad fact, here in the UK the old days of going to the junk yard and pulling your own used parts seem to be over. Health and safety apparently ☹️ I can remember first finding the delights of the junk yard with my brother, messing around while my dad and uncles pulled parts to fix their cars, a tradition I chose to carry on.
Happily my Land Rover Discovery still has a lever and cable to the transfer box to shift between high and low. Permanent four wheel drive on Disco 2s 😊
always a great video mr. O!!!!!
Do you ever get paranoid that someone is looking over you shoulder. I'm one of those people that need to see or touch to learn, you always teach me first time. Thank you
With the sniffer out of action, maybe a good time to do some jobs with old hypoid oil or engine tear downs.