Bought one based on this video for a 91 FLH Police bike. In my case I got junk. Accel pump barely worked no matter what I did. Ended up making a good one from it and the original I replaced.
I just finished the first test ride on my '97 WideGlide, and I'm a believer. My old factory carb was plum wore out at 41,000 miles, but even 6yrs ago, it didn't start, idle, or run like the 32 buck carb I got off of eBay. It feels like I gained 15 extra hp. Wonders never cease.
Every review I've seen of these was highly positive, and some say they're better than the stock Harley carb. I just ordered one off of eBay for my '97 WideGlide for 47 bucks with tax. I've been wrenching, building, and riding for 51yrs, and have always gone with whatever works, and what is most cost effective. When I have to work on a carb, I always replace every screw with Allen heads to avoid any future problems.
Not sure if they're 'better' than Harley, but trying to find a decent used HD carb that's cheaper than one of these is just getting impossible now a days.
I just had a sportster that came in with one of these carbs on it. I just cringed when I saw it. I have a lot of problems with the ebay carbs on a Japanese bikes but this harley ran remarkably well with it on it
I've installed about a dozen of them so far without any issues, plus people comment almost daily that they've had a great experience as well. They're a nice little surprise.
Perfect info for those who are not rely experienced with Chinese carbs. I do single carb conversions for Japanese bikes and these carbs are very good. You kick the ass. Thank you.
Just rebuilt my carb, it had 45/185 jets… Finally unplugged the slow speed jet and finished rebuilding.. Adjusted the idle and went from 2 1/2 out to maybe 2 out with my EZ Adjust and she seems happy happy. Test ride it was very peppy. Love my Champion Plugs!!! LOL (They just wear out faster, but I have a set of NGK for then)
I have one of those on a new to me Dyna and it works great so far. One note though, those bowl screws are very likely NOT Phillips but JIS (Japanese Industrial Standard) and won't strip if you use the correct JIS driver....that would be the case on the stock Kehin carb for sure. I didn't know the difference myself for years and stripped plenty of JIS screws. In a pinch you can grind the tip of a Phillips driver shorter and it will fit JIS screws better and be far less likely to strip them.
Both of my $40 clone S&S super E carbs work just fine. They are so exact, i believe that these are made from the same parts that wind up on the assembly line in Wisconsin.
Not a choke, actually a carb enrichment circuit, hence no butterfly to choke off air. When it pulls that needle out of carb body it allows more fuel to go through that passage for easier starting
Well technically @rc5693 is correct. Being a vintage auto mechanic, Ive always seen that a choke has a butterfly. When I started fiddling with this Harley carb, it has no butterfly and I then concluded it must be an enricher. An accelerator pump is an enricher, would you call that a choke? There is a difference like it or not. What ever its called, it sure helps to start the bike when its cold, thank god for that, especially with a kick start. By the way, this video was great, a tremendous help, thanks.
I'm working on a 88 883 n I'm putting amazon cv carburetor on it.i also agree all those HARLEY DAVIDSON parts are so expensive due to there HARLEY DAVIDSON.many aftermarket works great.ty for the video
Good instructional video. One suggestion....you might want to also mention about checking the float level. While you have the bowl off changing the jets, it's always a good idea to check the float to make sure it's within spec. Again, just a suggestion.
Seen a few vids on these carbs fitted one to my 1977 FLH stock bike 48/190 jets runs like a dream recommended upgrade from the stock carb. I'm with you on the nostalgic crap ride the bike daily and love it keep up the vids Bro
Those bottom screws are JIS, not Phillips. That is why so many people strip them out. :) I agree with you, I love me some carbs. They are very simple and easy to work on.
I cut the slide spring just a few turns and put 2 brass washers on the needle and went 48/180, and cleaned and greased the slide and slapped a 2 into 1 on and it runs so much better onthe highway and gets better mileage.
Same but i there's a after market kit i used with a smaller needle, bigger pilot & main jets and cut the spring too but I like the washers kuz there more adjustable all in my 79 ironhead 🔥💪👊
Thanks for the video man, I'm rebuilding my CV carb on my 91 xlh 1200. The ONLY difference i've noticed with my carb vs the 92 and up are the floats and emulsion tubes on the older style are a bit different. I got the replacement emulsion tube because the jets from the jet kit wont fit my 91 emulsion tube. The float replacement doesnt fit my carb which was a bummer, i'll have to find where to get the replacement for that.
I also run 180/48/2,5 turns on my 1340 shovelhead FXR. The guy I bought it from had installed a dyno-jet kit with a plastic vacuum slide a weird needle and the mixture screw bottomed out. "i cOuLdn'T gEt iT rUnNinG rIGhT...". No wonder. I run both S&S, OEM CV and knock off CV. They all work when properly set up.
Nice video, I may give it a shot one day when needed. Little tip get a JIS screwdriver has a different pitch then an American screwdriver and will not strip the screws.
I just went through installing an Amazon carb on my wife's 1200. I've been fighting a low end stumble. I know I'm already running the 48 but I'll have to check on the 180. I'll have to check out a choke relocation kit too. Fishing the cable between the cylinders is a pain. Thanks for the video. I'm about an hour west of STL in Cuba MO.
I pulled my old Buell Blast outta the cob webs to teach my kids how to ride, but the carb was missing pieces (probably vibrated off over the years, they don't call em thumpers for nothin). I didn't wanna spend the money on another H-D carb thats "worth" more than the bike. Picked up one of these with a choke cable and deleted the auto choke system and outta the box it was almost prefect. I think I'm gonna go up to the 180 or 185 on the final jet, it kinda coughs and cuts out at full throttle. But thanks to your video I saved a ton of money. I love my Buells, but always hated the H-D service bill. Once I started learning how to work on them myself, there was no going back to the dealerships, which worked out cause H-D axed the brand. Most of the Buells run these CV40 carbs with an "auto choke."
@@archstanton3379 I bought ours directly from China back when we had the shop, we ordered the ones that had the mounting flang that fitted the manifold of Shovels and Ironheads, back then HD carbs were still rebuildable, and could be had for a decent price, so we didn't need to order them for Evos.
THANK YOU FOR ALL YOUR INFORMATION ON THE AMAZON CARBURETOR I BOUGHT ONE AND SPITTING AND SPUTTERING CHANGED OUT THE JETS AND NOW I HAVE A SCREAMING EAGLE 🦅🦅🦅🦅 IT'S HARD TO HOLD THIS SPORTSTER 883 ON THE GROUND NOW. SIR YOU ROCK 🪨✝️🇺🇲🇺🇲🇺🇲🇺🇲🇺🇲🇺🇲🇺🇲🇺🇲🇺🇲
thanks for posting, the membranes are hard, and carbs are way too small on my vt1100c 1987. going to try cheap carburetors myself. foam rubber airfilter and cold as in freezing point, the bike did run like H. the 600cd have just a little smaller carbs :D dont know if original
So I have to give credit where credit is due, I bought the black w/shiny aluminum top one for $60 ...and runs way better than the stock CV ...I did have to replace bowl gasket and acell pump diaphragm due to small leaks but probably could have used sealant ... little rich but no CV cough my mind is blown.... keep up the good work !!!
What if you need gaskets and other parts for it, where would you get them? Would Harley stuff fit it? Oh and the one spark plug thing in the box, that is for the single cylinder Evo. I don't have anything against the carb. If it runs good by all means use it. I might try one myself. Thanks for the video.
Put one on my 02 bagger re-jetted it and had to use stock throttle cable guide. Started right up and adjusted idle and with mixture out 3 turns it runs better than ever! 100% 👍
No hate what so ever. I just installed one of these on my '73 Sportster 1000 XLCH and it immediately fired up and ran like a mad dog. Only minor adjustment was the idle. Other than that it was bolt on and go. Comes down to $35 including free shipping from Amazon or a couple of hundred bucks from JPCycles or Dennis Kirk.
I have no doubt is is a good carb. They are made in the same factory. I just don't like slide carbs like the CV or Mikuni but that is a personal choice. good video by the way.
Great video 👏👏👏 thank you for getting straight to the point . Can I ask will this would work on my XLH 1000 1984 bike ? It’s my first Harley and it comes with an S&S carb but I’ve been told swop it out for this one your talking about ! Also can you recommend a forum where I can pose my questions as I feel I’ll have a lot 😩😩😩😩 Like do all HD tanks fit all the frames ,what a good electronic ignition or should I keep the points 🤷🏻♂️🤷🏻♂️🤷🏻♂️🤷🏻♂️
Great vid! I looked at these for my bike and was about to drop 2 bills but you have given me new insight. I'm with it... If it works for you I will def give it a try. Thanks!
Got a similar cv carb for my xt225 a while ago. Been having hell getting it right. Seems to start decent but slowly dies as it heats up. Any advice would be appreciated.
Just curious if you've ever had an issue with float height setting being off on any of the Amazon carbs. I've got one of the early 40mm CV carbs that had the dual round floats that are hard to replace and have an Amazon carb in my cart as we speak. Thanks for the video. Really helpful!
I was wondering how this carburetor would work on a 1978 74 cu-in flh. I already have a CV carburetor (not S$S) I can't tell you what it is but its been on my ride for about 15 or 16 years now and it's time to get a new one.
So I had to revisit the comment section. Bike runs good with the China carb but I started to hear a strange rattle on Decel and sometimes when accelerating. Turns out the slide is made suuuuper loose. Much Looser than the slide in my 24 year old carb. Not going to take the risk of this breaking and getting sucked in. 😢
I been having a problem with mine i did a single cv carb swap on my 87 yamaha virago 535 my bike runs but the vacuum slide does not come up and it dies when i give it full throttle any help would be awesome
I saw you recommended a 48/180 set up in 1200 Sportster, was that correct?. I'm reading a 45 is tops on pilot. I have 883/1200 hop up with 45/170, runs good but want a bit more. Nice vids by the way, keep it up👍
great video ... thanks, I have a 2004 Road King with the Screemin' Eagle kit and cams, switched out the exhaust which has stamped on the top "NOT FOR STREET USE", I guess because they are quite a bit louder than the stock exhaust. The rest of the bike is stock. Can I use your setting for this bike and if not do you have a recommendation as to the jets etc. Thanks again, Clinton
@@STLNik I believe it is now a 96 ci 1550 cc. Would you still use the 190/48? Thank you so much for getting back to me so quickly and for the information, You rock ....
Sorry i know the video is about a year old lol. Im looking at doing a cv40 single carb conversion on my yamaha virago 535 and was wondering about jettings for set up. I was thinking 45 pilot and 155 main see how she goes
I've got a magneto xlch that I'm puting one of these puppies. I figure it should start easier with that effectively smaller venturi for starting. I just saw this vid about a year old. Have you had better luck with the chock cable not holding the chock button out? I've had several and it's that cheap plastic 'collet' that always fails to hold the chock. Thanks with a sub/likie
I've had great success with these carbs to the point of keeping them in stock in my shop, no choke issues to speak of. I usually install a new choke cable at the same time though. Thanks for watching
@@knowbody9679 James gasket seals and make sure your flanges are not warped by laying on a glass table to see if flat, the james gasket is a different design, it took me 3 trys and 2 seasons to get right...
@@teemann8379 Dude. Thanks. I just ordered some James gaskets. They are different. I bet they work. My flanges are straight. But I ordered those new also. Im still sending it to a shop next week so they can do it. Are you talking the blue James gaskets??
Hi, a question, How i put two carbs together (join) if I have tween carbs setup on my V- tween?(there is a single accelerator cable and a single choke cable) Thanks.
I checked Batteries plus, a local motorcycle supply shop and HD dealer- the one from batteries plus was $20 cheaper but fit poorly in the battery box (terminals positioned slightly differently). Went with the HD for fitment and it looks better since it’s exposed on my ‘03
Your the NEO YOU THE ONE I SPENT $50 I got $ ripped off Don’t tell me NEO Magic in the matrix baby you’re the one you’re the one you yes sir you’re the one
I new subscriber great I found uR Channel I buy Amazon all the time & need an New CV carb for my 2000 1200 xlc .w/ 35K miles .can you Please recommend witch brand to Buy Amazon ..Otherwise I guess ill Go with the Best & Most reviews ..Thanks In Advance
Hey brother could you recommend a intake manifold for a sv carb that will fit to a 2017 883 iron being converted from efi to carb. ..great vedio man👍👍👍👏👏👏
What jets you recommend for 90 Electra glide with an evo? It’s stock installed the cv and got it running but will cough it came installed with a 45/170
I have an amazon carb on an 89 883 i jusg bought, throttle cable is sloppy loose at max extension, and the new cable i bought for an 89 sporty seems to not have enough free length, any tipa on whag cable yall are running?
Does anybody recommend these Amazon CV cards for an 93-96 evo(electra glide classic/road king?)and...wud i jet it the same?the motor is a 1340...thanx alot fellas!
"Harley" Keihin CV carbs were not made in the USA in the first place. I disregard EVERY opinion by non-mechanics and avoid them because I dislike non-technical humans. Carbs were perfected over 100 years ago and the earliest still used today is the SU (Skinners Union) CV which is a piston type and still in production. HD plugs are branded Champions. I've ridden and wrenched HDs since before the posers took over the market and while selling Bubba with more money than sense paid off for HD I have nothing to do with those people. Real bikers wrench. Real car people wrench. Real gearheads wrench. Carbs BTW are so simple they're basically a toilet float with some plumbing. My long-deceased grandmother and mother drove a T Model Ford on their rural mail route in the 1930s and managed just fine with manual throttle and ignition levers. Anyone who CHOOSES to learn can do so. I've never been stranded by a carb. Not so with EFI pumps...
Is it bad idea to replace CV carburetor to a slide one in a 450cc dual cylinder chopper? what are the cons? hard to find a cv one for reasonable price..
Eaí cara, estou vendo seu vídeo do Brasil. Sei que não entende português, mas o RUclips irá traduzir automaticamente (risos) Então, eu tenho uma Yamaha virago 1100 ano 1994, e preciso substituir o carburador dela. Eu vi esse kit aí anunciado no Aliexpress com um preço bem legal para o Brasil. Acha que ele ficaria bom nela? Estou pensando seriamente em comprar, e sua opinião poderia ajudar bastante na decisão. Obrigado pela atenção, e pelo excelente vídeo Vlew
What do you think about adapting a pair of these on a 2.3 liter 4 cyl? Its got a stromberg cv carb and i cane across this looking for some tuning tips. Also curious if the lifting the piston method for air fuel tuning is applicable.
@@STLNik well it's not the effort really. If they work well and are easy to tune then it beats a lot of options money wise by a HUGE margin. I'm a fabricator so the intake isn't that big of a deal. And I'm thinking maybe it's a good option for triples on an inline six that has a pair of awful zenith 2 barrels.
Are the parts on these interchangeable with the original Keihn carb? I was thinking of putting the bowl with the drain on my stock carb to make it easier to winterize the bike.
Bought one based on this video for a 91 FLH Police bike. In my case I got junk. Accel pump barely worked no matter what I did. Ended up making a good one from it and the original I replaced.
I just finished the first test ride on my '97 WideGlide, and I'm a believer.
My old factory carb was plum wore out at 41,000 miles, but even 6yrs ago, it didn't start, idle, or run like the 32 buck carb I got off of eBay.
It feels like I gained 15 extra hp.
Wonders never cease.
I run the Amazon carb on my 06' sportster 1200. For $60 you can't lose. I love it and the Harley carb sits on the shelf rebuilt.
Every review I've seen of these was highly positive, and some say they're better than the stock Harley carb.
I just ordered one off of eBay for my '97 WideGlide for 47 bucks with tax.
I've been wrenching, building, and riding for 51yrs, and have always gone with whatever works, and what is most cost effective.
When I have to work on a carb, I always replace every screw with Allen heads to avoid any future problems.
Not sure if they're 'better' than Harley, but trying to find a decent used HD carb that's cheaper than one of these is just getting impossible now a days.
@@kct9967
So far, mine runs better than it ever did with the stock carb.
Only time will tell.
I just had a sportster that came in with one of these carbs on it. I just cringed when I saw it. I have a lot of problems with the ebay carbs on a Japanese bikes but this harley ran remarkably well with it on it
I've installed about a dozen of them so far without any issues, plus people comment almost daily that they've had a great experience as well. They're a nice little surprise.
Perfect info for those who are not rely experienced with Chinese carbs. I do single carb conversions for Japanese bikes and these carbs are very good. You kick the ass. Thank you.
Thanks for watching
Im looking to buy a carb for my 2000 honda shadow 600. Which amazon brand have you used?
@@crex16keep the stock ones, don't give yourself unnecessary headache. Don't expect your 30hp bike to go any faster
Missing my front carb on a 2002 marauder vz800 would you know what kind of carb I could use there like 200 plus on eBay
@@STLNik please help lol
My 93 883hugger has an Amazon cv carb and i couldnt be more happy with it!
I paid $44 for one of these. Jetted 170/48
Fired right up!!!
Just rebuilt my carb, it had 45/185 jets… Finally unplugged the slow speed jet and finished rebuilding.. Adjusted the idle and went from 2 1/2 out to maybe 2 out with my EZ Adjust and she seems happy happy. Test ride it was very peppy. Love my Champion Plugs!!! LOL (They just wear out faster, but I have a set of NGK for then)
I have one of those on a new to me Dyna and it works great so far. One note though, those bowl screws are very likely NOT Phillips but JIS (Japanese Industrial Standard) and won't strip if you use the correct JIS driver....that would be the case on the stock Kehin carb for sure. I didn't know the difference myself for years and stripped plenty of JIS screws. In a pinch you can grind the tip of a Phillips driver shorter and it will fit JIS screws better and be far less likely to strip them.
Both of my $40 clone S&S super E carbs work just fine. They are so exact, i believe that these are made from the same parts that wind up on the assembly line in Wisconsin.
I’ve been running a Amazon/eBay carb on my cammed evo in my dyna for 2.5 years and have had no issues whatsoever
Not a choke, actually a carb enrichment circuit, hence no butterfly to choke off air. When it pulls that needle out of carb body it allows more fuel to go through that passage for easier starting
Choke and enricher are used synonymously much like qtip and cotton swab
@@STLNik THANK YOU! I am so sick of hearing someone say " it's actually an enricher.........."
Well technically @rc5693 is correct. Being a vintage auto mechanic, Ive always seen that a choke has a butterfly. When I started fiddling with this Harley carb, it has no butterfly and I then concluded it must be an enricher. An accelerator pump is an enricher, would you call that a choke? There is a difference like it or not. What ever its called, it sure helps to start the bike when its cold, thank god for that, especially with a kick start. By the way, this video was great, a tremendous help, thanks.
I'm working on a 88 883 n I'm putting amazon cv carburetor on it.i also agree all those HARLEY DAVIDSON parts are so expensive due to there HARLEY DAVIDSON.many aftermarket works great.ty for the video
Good instructional video. One suggestion....you might want to also mention about checking the float level. While you have the bowl off changing the jets, it's always a good idea to check the float to make sure it's within spec. Again, just a suggestion.
Are specs on cv carb to have gas 1-2mm from float bowl gasket? I know everyone likes to eyeball it but I measure just wondering if this applies.
Seen a few vids on these carbs fitted one to my 1977 FLH stock bike 48/190 jets runs like a dream recommended upgrade from the stock carb. I'm with you on the nostalgic crap ride the bike daily and love it keep up the vids Bro
Thanks for the support
Those bottom screws are JIS, not Phillips. That is why so many people strip them out. :)
I agree with you, I love me some carbs. They are very simple and easy to work on.
I cut the slide spring just a few turns and put 2 brass washers on the needle and went 48/180, and cleaned and greased the slide and slapped a 2 into 1 on and it runs so much better onthe highway and gets better mileage.
What washers did you use? I bought two but both needles wobble like a weeble. I want to tighten them up in the needle seat.
Same but i there's a after market kit i used with a smaller needle, bigger pilot & main jets and cut the spring too but I like the washers kuz there more adjustable all in my 79 ironhead 🔥💪👊
@user-qk4ez1ls1u I used white lithium it was the smoothest I had
@@anti-popfpv4638 number 3 or 4 brass washers take the needle
80ci or XL?
I like my Mikuni VM 38 on my Shovelhead. If I want to replace it, I seen Amazon has those too!
Thanks for the video man, I'm rebuilding my CV carb on my 91 xlh 1200. The ONLY difference i've noticed with my carb vs the 92 and up are the floats and emulsion tubes on the older style are a bit different. I got the replacement emulsion tube because the jets from the jet kit wont fit my 91 emulsion tube. The float replacement doesnt fit my carb which was a bummer, i'll have to find where to get the replacement for that.
I also run 180/48/2,5 turns on my 1340 shovelhead FXR. The guy I bought it from had installed a dyno-jet kit with a plastic vacuum slide a weird needle and the mixture screw bottomed out. "i cOuLdn'T gEt iT rUnNinG rIGhT...". No wonder. I run both S&S, OEM CV and knock off CV. They all work when properly set up.
Nice video, I may give it a shot one day when needed. Little tip get a JIS screwdriver has a different pitch then an American screwdriver and will not strip the screws.
JIS screwdriver is a game changer. i bought a vessel megadora impacta from Amazon and it's been amazing i use it for everything
That’s what I have
I just went through installing an Amazon carb on my wife's 1200. I've been fighting a low end stumble. I know I'm already running the 48 but I'll have to check on the 180. I'll have to check out a choke relocation kit too. Fishing the cable between the cylinders is a pain. Thanks for the video. I'm about an hour west of STL in Cuba MO.
Low end stumble you may be over fueled. These settings work well for me but you might need to tweek a bit.
I pulled my old Buell Blast outta the cob webs to teach my kids how to ride, but the carb was missing pieces (probably vibrated off over the years, they don't call em thumpers for nothin). I didn't wanna spend the money on another H-D carb thats "worth" more than the bike. Picked up one of these with a choke cable and deleted the auto choke system and outta the box it was almost prefect. I think I'm gonna go up to the 180 or 185 on the final jet, it kinda coughs and cuts out at full throttle. But thanks to your video I saved a ton of money. I love my Buells, but always hated the H-D service bill. Once I started learning how to work on them myself, there was no going back to the dealerships, which worked out cause H-D axed the brand. Most of the Buells run these CV40 carbs with an "auto choke."
Love these carbs! I've been using these for my Shovelhead rebuilds for years, dirt cheap and work great!
@@archstanton3379 I bought ours directly from China back when we had the shop, we ordered the ones that had the mounting flang that fitted the manifold of Shovels and Ironheads, back then HD carbs were still rebuildable, and could be had for a decent price, so we didn't need to order them for Evos.
The honesty from :45 on got me!
Good video 👏🏻 I know you don’t like to do tutorials but I like this kind of video and you talking about the details
He is really good at it for sure.
Eh.......I guess we will agree to disagree
THANK YOU FOR ALL YOUR INFORMATION ON THE AMAZON CARBURETOR I BOUGHT ONE AND SPITTING AND SPUTTERING CHANGED OUT THE JETS AND NOW I HAVE A SCREAMING EAGLE 🦅🦅🦅🦅 IT'S HARD TO HOLD THIS SPORTSTER 883 ON THE GROUND NOW. SIR YOU ROCK 🪨✝️🇺🇲🇺🇲🇺🇲🇺🇲🇺🇲🇺🇲🇺🇲🇺🇲🇺🇲
hi you have install 180/48? thanks
I caught hell to . But I bought me one for my 98 wide glide and it's perfect
great tutorial. Just set up carb your way and it does run great and no cough
Used an Amazon CV 40 carb for my virago 535 bc the dual carbs were trashed and it works amazing, better even.
thanks for posting, the membranes are hard, and carbs are way too small on my vt1100c 1987. going to try cheap carburetors myself. foam rubber airfilter and cold as in freezing point, the bike did run like H. the 600cd have just a little smaller carbs :D dont know if original
So I have to give credit where credit is due, I bought the black w/shiny aluminum top one for $60 ...and runs way better than the stock CV ...I did have to replace bowl gasket and acell pump diaphragm due to small leaks but probably could have used sealant ... little rich but no CV cough my mind is blown.... keep up the good work !!!
I'm happy it worked out for you, thanks for watching.
What if you need gaskets and other parts for it, where would you get them? Would Harley stuff fit it? Oh and the one spark plug thing in the box, that is for the single cylinder Evo. I don't have anything against the carb. If it runs good by all means use it. I might try one myself. Thanks for the video.
Put one on my 02 bagger re-jetted it and had to use stock throttle cable guide. Started right up and adjusted idle and with mixture out 3 turns it runs better than ever! 100% 👍
I do not know why someone would worry about putting an Amazon carburetor on their bike when Harley uses parts from all over the world.
Ride safe.
Also you can notch the screw with a file so it never wipes off
Thanks for being the guinea pig! You seem to buy the lesser expensive parts and let us know how they work and perform. Thanks!
Somebody's gotta do it🤣🤣
No hate what so ever. I just installed one of these on my '73 Sportster 1000 XLCH and it immediately fired up and ran like a mad dog. Only minor adjustment was the idle. Other than that it was bolt on and go.
Comes down to $35 including free shipping from Amazon or a couple of hundred bucks from JPCycles or Dennis Kirk.
I have no doubt is is a good carb. They are made in the same factory. I just don't like slide carbs like the CV or Mikuni but that is a personal choice. good video by the way.
That choke bracket is $18.95 on LowBrow Customs now.
I put one on my 06 883. Went with the 42 pilot jet 45 was too rich. Runs perfect.
New to carbs , last bike was ego but I got a 98 883 turned into a 1200. You think I'd have to rejet it a bit bigger? Thanks 🙏🏼
Depending on exhaust and intake some variations will occur, I simply share what has worked for my setup
Great video 👏👏👏 thank you for getting straight to the point .
Can I ask will this would work on my XLH 1000 1984 bike ?
It’s my first Harley and it comes with an S&S carb but I’ve been told swop it out for this one your talking about !
Also can you recommend a forum where I can pose my questions as I feel I’ll have a lot 😩😩😩😩
Like do all HD tanks fit all the frames ,what a good electronic ignition or should I keep the points 🤷🏻♂️🤷🏻♂️🤷🏻♂️🤷🏻♂️
Chopcult.com has a forum with all the answers. You'd need a intake that fits the cv carb, so the s&s intake wouldn't work
Great vid! I looked at these for my bike and was about to drop 2 bills but you have given me new insight. I'm with it... If it works for you I will def give it a try. Thanks!
Great information! I'm going to try installing one on a Yamaha Road Star 1600
Thanks for the explanation,
But now I’m thinking how I can use these on a Honda st1100. 🤔
Any experience with the Mikuni knock offs ?
Not personally but the CV and S&S knockoffs have worked well.
Ever done a Mag Marelli to carb conversion ? I’d love to get your take on that.
I haven't but I know they're popular because that Mag Marelli system is crap.
@@STLNik I’m almost done with mine on 2000 RK. I rebuilt a cv carb but thinking about Mikuni now
Great carburettor, I picked on up after your last video
Awesome
Yeah, people say some funny things about funny stuff. Boy have I found that out this week lol. Great video thanks for sharing
The comment sections can be rather entertaining
@@STLNik for Shure
I like my stocker just fine I was worried about adding a thunder jet but fuck it I guess lol
If you go to cvp and get , emulsion tube , accelerator pump nozzle and softer spring CV will RIP. If making big power they have hi Flo inlet as well .
And custom needle as well
Carbs simple to me iv worked on them 36 years lol iv split no telling how many crank cases on dirt and street bikes over the years
Got a similar cv carb for my xt225 a while ago. Been having hell getting it right. Seems to start decent but slowly dies as it heats up. Any advice would be appreciated.
Im running a knock off s&s carb. 45$. Besides wrong accelerator pump in it. Ps. Cv carbs is right one. Thing rips nuts on my 1200 sporty
Just curious if you've ever had an issue with float height setting being off on any of the Amazon carbs. I've got one of the early 40mm CV carbs that had the dual round floats that are hard to replace and have an Amazon carb in my cart as we speak. Thanks for the video. Really helpful!
I've never had a single issue with anything on these. I actually keep a couple in stock for customers.
I was wondering how this carburetor would work on a 1978 74 cu-in flh.
I already have a CV carburetor (not S$S) I can't tell you what it is but its been on my ride for about 15 or 16 years now and it's time to get a new one.
So I had to revisit the comment section. Bike runs good with the China carb but I started to hear a strange rattle on Decel and sometimes when accelerating. Turns out the slide is made suuuuper loose. Much Looser than the slide in my 24 year old carb. Not going to take the risk of this breaking and getting sucked in. 😢
I been having a problem with mine i did a single cv carb swap on my 87 yamaha virago 535 my bike runs but the vacuum slide does not come up and it dies when i give it full throttle any help would be awesome
I saw you recommended a 48/180 set up in 1200 Sportster, was that correct?. I'm reading a 45 is tops on pilot. I have 883/1200 hop up with 45/170, runs good but want a bit more. Nice vids by the way, keep it up👍
45 would be fine, i like to run a bit fat because ive melted a piston before.
@@STLNik I just got a 48 and 180, worth trying them?
I bought one for $56 that came with choke cable.
great video ... thanks, I have a 2004 Road King with the Screemin' Eagle kit and cams, switched out the exhaust which has stamped on the top "NOT FOR STREET USE", I guess because they are quite a bit louder than the stock exhaust. The rest of the bike is stock.
Can I use your setting for this bike and if not do you have a recommendation as to the jets etc.
Thanks again, Clinton
04 would be an 88ci, i would start with 190/48.
@@STLNik I believe it is now a 96 ci 1550 cc. Would you still use the 190/48? Thank you so much for getting back to me so quickly and for the information, You rock ....
96 with a cam and exhaust start with a 195/50 and give that a try. I'd rather be a little fat than a little lean
Sick, I just ordered one of these. $45 on blackfriday with free shipping.
I have a 2003 Heritage that am going to put a CV40 off ebay
Sorry i know the video is about a year old lol. Im looking at doing a cv40 single carb conversion on my yamaha virago 535 and was wondering about jettings for set up. I was thinking 45 pilot and 155 main see how she goes
I've got a magneto xlch that I'm puting one of these puppies. I figure it should start easier with that effectively smaller venturi for starting.
I just saw this vid about a year old. Have you had better luck with the chock cable not holding the chock button out? I've had several and it's that cheap plastic 'collet' that always fails to hold the chock.
Thanks with a sub/likie
I've had great success with these carbs to the point of keeping them in stock in my shop, no choke issues to speak of. I usually install a new choke cable at the same time though. Thanks for watching
After watching this I took a chance on one. Could never get the stock carb dialed in (PO had a dynojet kit). Runs better, smoother. Thanks man. 🔥
My 04 fxd has brass inlet but I'm like the 5th owner and got it with under 6k and leaky intake seals
Dude. My 97 fatboy has leaking seals and I cannot get them sealed to save my life. I’m sending it to a shop. I’m at my wits end
@@knowbody9679 James gasket seals and make sure your flanges are not warped by laying on a glass table to see if flat, the james gasket is a different design, it took me 3 trys and 2 seasons to get right...
@@knowbody9679 also clean the mating surface and grease the seals you will feel them suction into place...
@@teemann8379
Dude. Thanks. I just ordered some James gaskets. They are different. I bet they work. My flanges are straight. But I ordered those new also. Im still sending it to a shop next week so they can do it. Are you talking the blue James gaskets??
@@knowbody9679 yea it fits over the end like wraps around it with a groove so it rides on the gasket and seats better
I like them too. Keep pushing cheers
Can you put a link in the description for 2000 harley spoerster 1200c?
Hi, a question, How i put two carbs together (join) if I have tween carbs setup on my V- tween?(there is a single accelerator cable and a single choke cable) Thanks.
A carb kit you can get for 15 to 20 bucks.
Maybe the basic seal kits, but I haven't seen a total rebuild kit that cheap.
@@STLNik I've bought entire kits for that much.
@@SaddleTrampTV send a link of this 20 bucks full rebuild kit.
A 88ci 2003 carb factory 45/190 whats your opinion on this set?
On my new carb the accelerator pump isn’t working on mine not spraying fuel from the nozzle
I’ll never buy another battery for my Harley off of Amazon
I buy orilleys batteries so I can have a nationwide warranty.
I checked Batteries plus, a local motorcycle supply shop and HD dealer- the one from batteries plus was $20 cheaper but fit poorly in the battery box (terminals positioned slightly differently). Went with the HD for fitment and it looks better since it’s exposed on my ‘03
Your the NEO
YOU THE ONE
I SPENT $50
I got $ ripped off
Don’t tell me NEO
Magic in the matrix baby you’re the one you’re the one you yes sir you’re the one
I new subscriber great I found uR Channel I buy Amazon all the time & need an New CV carb for my 2000 1200 xlc .w/ 35K miles .can you Please recommend witch brand to Buy Amazon ..Otherwise I guess ill Go with the Best & Most reviews ..Thanks In Advance
What was the float level?
Hey brother could you recommend a intake manifold for a sv carb that will fit to a 2017 883 iron being converted from efi to carb. ..great vedio man👍👍👍👏👏👏
I believe you'll need the intake manifold from a 04-06 sportster. I'd try to find a used one on ebay.
@@STLNik thanks so much I'll start looking👍👍👍👍👍
What jets you recommend for 90 Electra glide with an evo? It’s stock installed the cv and got it running but will cough it came installed with a 45/170
Exactly what brand/manufacturer of Chinese carburetor do you buy? I have noticed several different brands.
I have an amazon carb on an 89 883 i jusg bought, throttle cable is sloppy loose at max extension, and the new cable i bought for an 89 sporty seems to not have enough free length, any tipa on whag cable yall are running?
How many turns out did it take to tune that one?
Does anybody recommend these Amazon CV cards for an 93-96 evo(electra glide classic/road king?)and...wud i jet it the same?the motor is a 1340...thanx alot fellas!
cool bike man!
Does that have the pumper, is it the cvk40 do you have a link for that one
"Harley" Keihin CV carbs were not made in the USA in the first place. I disregard EVERY opinion by non-mechanics and avoid them because I dislike non-technical humans.
Carbs were perfected over 100 years ago and the earliest still used today is the SU (Skinners Union) CV which is a piston type and still in production.
HD plugs are branded Champions. I've ridden and wrenched HDs since before the posers took over the market and while selling Bubba with more money than sense paid off for HD
I have nothing to do with those people. Real bikers wrench. Real car people wrench. Real gearheads wrench.
Carbs BTW are so simple they're basically a toilet float with some plumbing. My long-deceased grandmother and mother drove a T Model Ford on their rural mail route in the 1930s
and managed just fine with manual throttle and ignition levers. Anyone who CHOOSES to learn can do so. I've never been stranded by a carb. Not so with EFI pumps...
Is it bad idea to replace CV carburetor to a slide one in a 450cc dual cylinder chopper? what are the cons? hard to find a cv one for reasonable price..
Can this be changed to a single throttle cable? Do you have the links to what you purchased? I have a 88 1200 that I am building.
I use mine with just a single throttle cable. If you search cv carb on Amazon they will come up.
Great information 👍🏻
What would you do different to the carb for the big twin engines?
Just look up the proper jet sizes for your displacement. I usually find the factory size and go up 1
Nice job! mines running good 😁
HOWdy STL-Nik, ...
Thanks
COOP
the WiSeNhEiMeR from Richmond, INDIANA
...
...
Can I please buy the stock cv40 from you ? let’s work out a price. Thank You 🙏🏼
Eaí cara, estou vendo seu vídeo do Brasil.
Sei que não entende português, mas o RUclips irá traduzir automaticamente (risos)
Então, eu tenho uma Yamaha virago 1100 ano 1994, e preciso substituir o carburador dela.
Eu vi esse kit aí anunciado no Aliexpress com um preço bem legal para o Brasil.
Acha que ele ficaria bom nela? Estou pensando seriamente em comprar, e sua opinião poderia ajudar bastante na decisão.
Obrigado pela atenção, e pelo excelente vídeo
Vlew
What jets would you recommend for a 2000 Harley fat boy 1340 ??
What do you think about adapting a pair of these on a 2.3 liter 4 cyl? Its got a stromberg cv carb and i cane across this looking for some tuning tips. Also curious if the lifting the piston method for air fuel tuning is applicable.
I'm sure it could be done but I'm not sure it would be worth the effort.
@@STLNik well it's not the effort really. If they work well and are easy to tune then it beats a lot of options money wise by a HUGE margin. I'm a fabricator so the intake isn't that big of a deal. And I'm thinking maybe it's a good option for triples on an inline six that has a pair of awful zenith 2 barrels.
Very informative thanks
Are the parts on these interchangeable with the original Keihn carb? I was thinking of putting the bowl with the drain on my stock carb to make it easier to winterize the bike.
The screws are metric thread but other than that it should line up
Thanks@@STLNik
Thanks for your information...🤘🏼
Which one would you go with for a dyna 88