maaan :D i have seen people dropping the tire into hot water for a short time but hitting up the microwave is on another lever! great video mate, keep'em coming
While at this I recommend that one also replace the ball bearings. Especially if one still has the original bearings on (They're crap) I recommend using bearings of a known good brand such as SKF or NSK.
@@jaydenplaysguitar3896 It's more to improve lifetime and be proactive against catastrophic failure. I had a hub motor from this particular scooter fail on me. Once the bearings started to degrade, it was degrading so quickly the motor was more or less destroyed when I got back home. Yeah I should've carried it home instead, but stupidity wins over wisdom every time ;)
@@jaydenplaysguitar3896 Once the crappy original bearings are replaced with a pair of good ones (i.e. SKF) it should hold up a lot longer. How long all depends on how one drives, and what one drives on.
Сразу видно, что не механик. А колесные гайки заранее откручены. Использование рожкового ключа признак отсутствия квалификации и опыта. Эту гайку не открутить Рожковым ключом. Только головка или звездочка с одной стороны и ключ для трубных гаек или разрезанная звездочка с другой. Металлическим молотком НЕЛЬЗЯ стучать по алюминию! Либо приставка, либо резиновый молоток.
Большое спасибо за советы)) это больше видео для тех кто хочет поменять в домашних условиях. Сколько стучали, проблем небыло, и так откручиваються легче. Естественно раз на раз не приходиться, но работает.
They're called "Security Torx bits". Like regular Torx bits, but with a hole drilled in their center, which allows the pin in the screw head to go into. The idea is to prevent "home" mechanics with regular torx bits from being able to remove those screws. But you can buy the bits online. If you're in the USA, you can get a cheap set from Harbor Freight: www.harborfreight.com/security-bit-set-33-pc-68459.html
Does anyone know if it's possible to change the E22E tyres from the ones like the Model D? The E22E uses a 9-Inch Dual Density tyres (flat-free) and the Ninebot model D uses 10-inch air tyres with inner tube. can someone give some feedback. I'll love to change if was possible. The original tyres from e22e model it's very uncomfortable, they are only good if we have a good road without holes or if you ride on a cycle track otherwise is very bad. Thanks.
did you hit a pothole or some kind of step? try to disconnect cable for source of power, wait for few minutes, then plug it back and see if code error is gone. good luck.
i advice anyone who is trying to do this on an es2 to not bother, and just buy a new motor with a new wheel attached on it, at least if you have an older scooter like me, after days of trying, special tools bought, 50% of the screws broken and when i finally get off all the broken shit quality screws, the wheel literally is just impossible to get on, literally boiled the wheel, slapped on half a bottle of lube on that shit and it is just still impossible. idk which scooter or wheel he has but mine are 1000x more difficult, i have been defeated by this horribly made scooter and will just replace the whole motor.
Can't believe u just used your hands to put these crazy tires in.. Lol.. Amazing.. 👐🏻
I tried so many different options...happy to share with audience the outcome :)
maaan :D i have seen people dropping the tire into hot water for a short time but hitting up the microwave is on another lever!
great video mate, keep'em coming
That's what I would of done. He's doing got the hard way for sure.
You are great bro, I learned from you, I have my ES2 also, sooner will change my tire too, subscribed already, thank you 😊👌
Thank you for posting. This was super easy thanks to your video.
Great video! Do you have a video for back tire as well?
Thank you very much for this video.
It works great 👍
While at this I recommend that one also replace the ball bearings. Especially if one still has the original bearings on (They're crap)
I recommend using bearings of a known good brand such as SKF or NSK.
Does this improve the overall ride? If so by how much?
@@jaydenplaysguitar3896 It's more to improve lifetime and be proactive against catastrophic failure. I had a hub motor from this particular scooter fail on me. Once the bearings started to degrade, it was degrading so quickly the motor was more or less destroyed when I got back home. Yeah I should've carried it home instead, but stupidity wins over wisdom every time ;)
@@sysghost So how would you reccomend to maintain a motor? Replace bearings ever so often?
And could you link to some good bearings please for the ninebot es2?
@@jaydenplaysguitar3896 Once the crappy original bearings are replaced with a pair of good ones (i.e. SKF) it should hold up a lot longer. How long all depends on how one drives, and what one drives on.
요게 훨씬 쉬워보이네요.감사합니다!
Beautiful song....what’s the name?
All i needed to know was how you removed the hub plate then at 4.09 it was done without showing!!
Well done mate it magicked it self apart
Hey, what spanner does he use to unscrew the crews on the front wheel?
since i broke my wires on the inside of the tire and dont want to mess with it, could i please have a link for original ninebot es4 front wheel motor?
Om cara bedain es 1, 2, 3 dan 4 di mana nya om?
Saya lagi nyari yg baterai awet dan speed nya kenceng, rencananya buat ngojol Grab ambil orderan food
damn you could kill a bears with that hands' strength
Сразу видно, что не механик.
А колесные гайки заранее откручены.
Использование рожкового ключа признак отсутствия квалификации и опыта.
Эту гайку не открутить Рожковым ключом.
Только головка или звездочка с одной стороны и ключ для трубных гаек или разрезанная звездочка с другой.
Металлическим молотком НЕЛЬЗЯ стучать по алюминию!
Либо приставка, либо резиновый молоток.
Большое спасибо за советы)) это больше видео для тех кто хочет поменять в домашних условиях. Сколько стучали, проблем небыло, и так откручиваються легче. Естественно раз на раз не приходиться, но работает.
Bro why is it impossible to find front tire replacements
Also, can you use the real wheel for the front?
What do you mean ypu cannot find front tyre replacements? I think this video is about tyre replacement :)
Great video!! One question... is possible input or this Ninebot neumatics of t 10 " ??? Sorry for my English is not good.
Thank you for the video. How much do I need to microwave the tires?
@@smk4063 10 seconds few times with little break
Hi, do you know if ES2 front motor works on ES1?
Hi nice video.. Can I assume that since a solid tire is flat free it won't need replacing as often as a pneumatic tire?
The tread wears down pretty bad in the center of the tread, much worse that if it were air-filled.
Какой размер резины покупал? Inch 8.5 Подходит?
8.5 no specialnaja dlia segway es modeli
@@ninebotfix4589 Напиши какой подходит размер
www.ebay.co.uk/itm/ES1-ES2-ES3-ES4-Electric-Scooter-Tires-for-Ninebot-Non-pneumatic-Wheel-Tyre-w-/124366536348?_trksid=p2349624.m46890.l49286
@@ninebotfix4589 ok thank you 😀👍
@@ninebotfix4589 у меня scooter KUGOO 2 KIRIN . Подойдёт ? 50/75-6.1 (81/2x2)
What kind of bit or socket fits on those 5 screws on the front wheel ? Thanks
They're called "Security Torx bits". Like regular Torx bits, but with a hole drilled in their center, which allows the pin in the screw head to go into. The idea is to prevent "home" mechanics with regular torx bits from being able to remove those screws. But you can buy the bits online. If you're in the USA, you can get a cheap set from Harbor Freight: www.harborfreight.com/security-bit-set-33-pc-68459.html
@@HangarQueen what number is that, though?
@@MrHumorization T25
@@HangarQueen THANK YOU SO MUCH! My local lowes only had 1 size and they did not fit.
Hmm does the soap not make it slide on the rim inside and fall of later?.
Nope :)
thanks
Wow top video
Do you know if this will work on the es3 .?
Es2 3 4 same scooters
Hi, where did you purchase the tire from? I bought a 200x50 size tire which does not fit on ES1
I did use same tire btw. And i did put it on. It took much strength of 2 people. And i did allmost boil it before. Also screwdriver also helps.
Does anyone know if it's possible to change the E22E tyres from the ones like the Model D?
The E22E uses a 9-Inch Dual Density tyres (flat-free) and the Ninebot model D uses 10-inch air tyres with inner tube. can someone give some feedback. I'll love to change if was possible. The original tyres from e22e model it's very uncomfortable, they are only good if we have a good road without holes or if you ride on a cycle track otherwise is very bad.
Thanks.
Did you manage to do it
I think you could use the solid tires of xiaomi m365 but need some modification because this is little bigger
good info but the music was too much
doesnt say what exact tool he used to open the screws, so not helpful at all as none of my tools works on them. RIP
What is the number for the torx key?
T25 for the tire
Hey man you are the best , do you know how to fix error code 48 on es4
did you hit a pothole or some kind of step? try to disconnect cable for source of power, wait for few minutes, then plug it back and see if code error is gone. good luck.
You should have shown the whole proccess and recorded comments later and eddited the two over each other this is hard to follow
Tengo una mano. Me está asiendo un ruido al frente que puede ser ai mismo en la goma de al frente
Как камера с перфорацией
Я думал Пугачева ?
Hi, can you share the link from where you bought the tires? Thanks
I was orderi g from Chinesse supplier. You can try Aliexpress or Ebay.
На гайки фиксатор синий надо мазать
Salve Buonasera Ci illumino Patini bloccata la programmata un telefono prima funziona e dopo bloccata
i broke wires inside the wheel
Get a new motor. Not too expensive. I prefer to change motor rather than play with wires. Good luck!
can i have a link? it happened cause the tire was too small, i need a link of original ninebot es4 motor, thank you👊👍
Lol can’t hear an F*ing word. But thanks for the video
i advice anyone who is trying to do this on an es2 to not bother, and just buy a new motor with a new wheel attached on it, at least if you have an older scooter like me, after days of trying, special tools bought, 50% of the screws broken and when i finally get off all the broken shit quality screws, the wheel literally is just impossible to get on, literally boiled the wheel, slapped on half a bottle of lube on that shit and it is just still impossible. idk which scooter or wheel he has but mine are 1000x more difficult, i have been defeated by this horribly made scooter and will just replace the whole motor.
WTF i dont unplug wires i change tire in 5 min max witch screews
Mechanic not good