You know you could put older model door handle off 80's ford trucks that will not break off like the 90's models, with just a little grinding. Love your channel. God Bless you. Brother
Sergio comes in clutch when you need him the most and when he comes and saves the day, you can tell that’s a dedicated man and loves doing what he does.
The best part about doing all those fixes is for the next week it will feel like a new truck! It's a bit learning curve but 3D printing is very helpful for replacing little parts like the plastic bushing on the push rods in the door.
get one out of the south, not new hampshire like i did... rust. rust. rust. lotta time replacing rusted stuff that occurs over time, what looked fine when i bought it
Ah I worked for a Ford dealer and this was my specialty. Just did all my Toyotas doors clean lube rein install. It is good to have small hands. Always enjoy someone else. all good fun fun.
I stayed in Pomona all of ‘21, and took my car Ronnie’s because of you! Adam and the crew there set me up with some Audio Dynamics, and the same radio as yours, and I haven’t had an issue yet!
Nice work on all the repairs ? Sometimes you don't have to know everything you just have to know who to ask. Watching this made me glad I don't work on cars anymore, especially since I didn't do it for pay. 😉👍
Bro, hit the door mech with the gun cleaner lubricant in an aerosol can, use a lot and work the door handle. Let it dry and hit it with some lithium grease spray can, the dry stuff and it will work. I think I have had 6 OBS since they were actually new. I replaced one of those then never again. Hell, used the same setup on my 1973 bronco and works a treat.
Most gratifying feeling when you pull That door handle and it actually works😂 watching you finagle that out of the door gave me PTSD I HATED taking my obs door panels off.
actually I think I'm gonna take the old S10 Blazer LT Tahoe I have and start upgrading with non OEM parts for the the lighting and other stuff. I just installed sealed high power LED headlights. still gotta take it to the mechanic and get him to wire the in lamp blinker and day running lamp but..I love what I installed I do . Getting the rear panel off on the door that won't unlock is "simple" pull the back bench out. :P dude! it all works! awesome work Ryno.
hey ryan, if you can save one of the plastic piece that is nearly complete (or not totally broken) i can print you replacements in a few hours time. Like a few dozen at once if that helps.
The door lock actuator went bad on my back driver side on the old obs I use to have. Couldn’t open that door for along time and it was very annoying lol.
My brother in-laws keep wanting to buy older trucks and I tell them, you have to be ready for an old truck, I have a 93 k1500 and the parts guy kept telling me dude you're going to have a new truck by the time your done!!🤦 And he wasn't wrong 🤣🤣
I have a 92 F250 obs and my door lock would work on the power but would not work with the key. I decided to take the latch out and it turns out there's bracing in the way but I did get it out enough to get the key lever rod which was stuck got it unjammed able to put it back together. But luckily I did not have to replace the latch. I then sprayed the latch and key assembly with lube and it seems to work. It could be I was just trying to take it out wrong. Hopefully it was easier for you.
That's what I thought when I bought my 97F350 that it was just gonna need a little love 😘a lot of love and a whole lot of money later🤑 it's still broken and still eating parts and still breaking my heart🤣 Just wait until you start breaking door cables and door handles and then the door metal itself becomes weak and then you have to reinforce that and then you try and find the little switches that open the windows and locks and the ones you get are kind of sort of one size fits all of every Ford model🤣
So I had a f150 door had the same issue power windows power locks and let me tell you your lucky you didn’t cut your hand open I dreaded having to replace my door handle assembly and the exterior part as well
Sergios friend is the kind of Mexicans I'm used to dealing with. They get it done no jokes no games just work. He understands everything he just prefers to deal through his own.
my 2016 is hving door lock issues going off the fritts lights included any help is appricated! cant afford the $125 an hour my local ford dealer wants to just look into it not including fixing it sadly they were stumped when i asked them question ahh its so frusterating! great uploads buddy!!! wait for them all haha
I feel ur pain bro lol I'm going thru the same shit with my jeep window s and lock s , always hated mess n with wiring , got a short in the driver's door wire s & nothing works
A lot of time with those parts you ordered for your vehicle especially for the door they want you to reuse those little plastic clips that are already in your door. I mean you can order them, but they cost twice as much then they have to be and only the manufacture of your vehicle has those clips unless you can 3-D print your own clips which I couldn’t for my little 99 Tacoma so I ordered stupid expensive clips
Very easily? It wasn’t fun getting it out of a decent door in my own shop, let alone trying to rip an old one out of a beat up truck in a junkyard. These notoriously fail, I wouldn’t want a used one
Damn you are treating this truck like shit. I use to really love your obs vids and even did similar things to mine but you have completely tainted that for me. Disrespectful to an amazing truck!
Man I hope Sergio needs some concrete work or excavation done soon it would be nice to see you working for him for a change 😂😂😂
😂😂😂
For reals
I’m sure he gets paid good
I'm sure Ryan always hooks it up for him
@@brodytingley3542 I don’t doubt that for a minute and I’m sure he loves all the free advertising as well
You know you could put older model door handle off 80's ford trucks that will not break off like the 90's models, with just a little grinding. Love your channel. God Bless you. Brother
Sergio comes in clutch when you need him the most and when he comes and saves the day, you can tell that’s a dedicated man and loves doing what he does.
The best part about doing all those fixes is for the next week it will feel like a new truck! It's a bit learning curve but 3D printing is very helpful for replacing little parts like the plastic bushing on the push rods in the door.
Autozone…$4
pex tubing , 15' for $5, lifetime supply
@@iansteward4708 trueeee but 3D PRINTERRRRRRRR
It's cool that you razz Chris and have him get in front of the camera, too. He seems like a great dude, taking it all in stride. WorkForIt.
honestly your a reason why i want a obs working towards getting me one!
get one out of the south, not new hampshire like i did... rust. rust. rust. lotta time replacing rusted stuff that occurs over time, what looked fine when i bought it
Ah I worked for a Ford dealer and this was my specialty. Just did all my Toyotas doors clean lube rein install. It is good to have small hands. Always enjoy someone else. all good fun fun.
You are now on your way to fixing even the small stuff on your obs because you are ocd and you will enjoy the truck so much more
I stayed in Pomona all of ‘21, and took my car Ronnie’s because of you! Adam and the crew there set me up with some Audio Dynamics, and the same radio as yours, and I haven’t had an issue yet!
Nice work on all the repairs ?
Sometimes you don't have to know everything you just have to know who to ask.
Watching this made me glad I don't work on cars anymore, especially since I didn't do it for pay. 😉👍
When the gentleman bring out the 12” extendo with an angle shaft. Ohhhhh boy it’s going to be ruff 🐶
That piece you pulled out of the door goes at the bottom corner of the door where that vent is.
The guy who changed out the actuator is quite interesting. Can't understand what he's saying but he gets stuff done.
That's alright, he probably can't understand you either...
@@sykwookiee that's likely the case.
You Worked for it for sure on that door handle. Good job man.
Love all the content but the OBS videos are definitely always my favorite 👍🏼
Your the goat ryno one very intelligent man and I glad you share it with us
Bro, hit the door mech with the gun cleaner lubricant in an aerosol can, use a lot and work the door handle. Let it dry and hit it with some lithium grease spray can, the dry stuff and it will work. I think I have had 6 OBS since they were actually new. I replaced one of those then never again. Hell, used the same setup on my 1973 bronco and works a treat.
Most gratifying feeling when you pull That door handle and it actually works😂 watching you finagle that out of the door gave me PTSD I HATED taking my obs door panels off.
You give the courage to take on any project becuz boy that was a doozy
I did (6) 6.5 sundown x subs behind the seat on 3k in the same truck. Super impressive and still have room back there.
I use to go to the junkyard and look for replacements and I used to sand the connector parts so I cleaned them up and install them (switches)
Always fun to update ol trusty.
always makes my mondays better thanks ryno
😅 one of the best thing about my 89 Chevy k1500 is the inner skin on the door can be fully removed
Sergio always coming clutch
Good old OBS door panels 😵💫😵💫
When will you do something with your other Obs ford the single cab ?
Nice selection of tunes. Love Wade Bowen
i need to show my obs some love
What about the plastic deals that hold the door panel on that clip into the back of the door panel and then pop into the door
What year is your truck and your truck is beautiful
actually I think I'm gonna take the old S10 Blazer LT Tahoe I have and start upgrading with non OEM parts for the the lighting and other stuff. I just installed sealed high power LED headlights. still gotta take it to the mechanic and get him to wire the in lamp blinker and day running lamp but..I love what I installed I do .
Getting the rear panel off on the door that won't unlock is "simple" pull the back bench out. :P
dude! it all works! awesome work Ryno.
hey ryan, if you can save one of the plastic piece that is nearly complete (or not totally broken) i can print you replacements in a few hours time. Like a few dozen at once if that helps.
The door lock actuator went bad on my back driver side on the old obs I use to have. Couldn’t open that door for along time and it was very annoying lol.
Genuinley got excited for the driver door handle fix i know how annoying things like thay can be
My brother in-laws keep wanting to buy older trucks and I tell them, you have to be ready for an old truck, I have a 93 k1500 and the parts guy kept telling me dude you're going to have a new truck by the time your done!!🤦 And he wasn't wrong 🤣🤣
You should rivet on the window trim to the door panel, that way it doesnt keep coming off.
ever, again, like when a window regulator tanks haha
I have a 92 F250 obs and my door lock would work on the power but would not work with the key. I decided to take the latch out and it turns out there's bracing in the way but I did get it out enough to get the key lever rod which was stuck got it unjammed able to put it back together. But luckily I did not have to replace the latch. I then sprayed the latch and key assembly with lube and it seems to work. It could be I was just trying to take it out wrong. Hopefully it was easier for you.
After seeing the rest of your video if I run into that issue again I will try sliding the track up like you did. Thanks for your determination
That's what I thought when I bought my 97F350 that it was just gonna need a little love 😘a lot of love and a whole lot of money later🤑 it's still broken and still eating parts and still breaking my heart🤣 Just wait until you start breaking door cables and door handles and then the door metal itself becomes weak and then you have to reinforce that and then you try and find the little switches that open the windows and locks and the ones you get are kind of sort of one size fits all of every Ford model🤣
They have all those plastic clips and bushings ate AutoZone and NAPA
You got a link for the factory screws ?
I got the same radio and I love it
My truck has the same problem with the back door locks
Hey Bud, I learned a few things today that is always good. Later.
What kind of deck are you using? Can you use Google maps with it? I want to do something similar with my OBS F150.
Cheap Dorman brand door bushings from autozone are also going to make a huge difference! Look them up!
Great stuff
So I had a f150 door had the same issue power windows power locks and let me tell you your lucky you didn’t cut your hand open I dreaded having to replace my door handle assembly and the exterior part as well
Hey Ryan can you do a video of how you wired your Chevy mirrors to your oem ford switch I’m also struggling 😂😫😅
Keep up the amazing work. My buddy had a few OBS for parts in Lancaster ca
Sergios friend is the kind of Mexicans I'm used to dealing with. They get it done no jokes no games just work. He understands everything he just prefers to deal through his own.
Heck yeah man day is complete got a dmax video
Talking about a can of worms, started with the driver side door handle. Finding all sorts of door issues
Anything worth doing, ya gotta work for it
Work for it💪💪
What do you or Zach recommend for grease for sealed bearing
Been waiting for this one 😂
The door pull handle can be taken off and on with the door panel intstalled. Makes it alot easier to remove the door panel and install the door panel.
my 2016 is hving door lock issues going off the fritts lights included any help is appricated! cant afford the $125 an hour my local ford dealer wants to just look into it not including fixing it sadly they were stumped when i asked them question ahh its so frusterating! great uploads buddy!!! wait for them all haha
That is why I do my best to find someone else to fix it because I don’t know what I am doing with them ether
Seems like you have had alot of problems with the sound system. Not a good look for that stereo shop that did the install.
Hey I gotta mint 40/20/40 seat you could have for the rear same opal gray,
That for him only or you cool selling it? I’d be interested for my Obs.
When will you regret not going to the parts store to get some new plastic pieces to replace the old ones?
Hanes manual is needed for your truck
I believe that it's Haynes, but you are absolutely correct sir...
@@sykwookiee you’re right but yes it’s the favorite of all non mechanics
What's driving me nuts the most is your steering wheel! When are you replacing that?!?! Lol
2 idiots garage comes thru 👌🏻👍🏻
did you fire zack??
YES MORE OBS CONTENT
Sergio’s homie reminds me of those guys that work on car in tee-jay, can dismantle a car in like 10 mins…
Awesome 👌
That face when they were drilling your door.... Hahahaha
What color is that truck
Don't worry I know how you feel about the doors I got 97 350 the way we get back doors open we got keep tapping the unlock button
Salute 💯🤟🏻
I feel ur pain bro lol I'm going thru the same shit with my jeep window s and lock s , always hated mess n with wiring , got a short in the driver's door wire s & nothing works
Ryan you get an A for effort 😂😂😂
Ryan who's your favorite red dirt music artist?
Playing some Whiskey Myers I see! Niceeeeee
the black vent goes behind the metal louvers inside the door
Time for custom made door panels
A lot of time with those parts you ordered for your vehicle especially for the door they want you to reuse those little plastic clips that are already in your door. I mean you can order them, but they cost twice as much then they have to be and only the manufacture of your vehicle has those clips unless you can 3-D print your own clips which I couldn’t for my little 99 Tacoma so I ordered stupid expensive clips
Where is Zach
I thought a Ford would unlock from just opening up the door with the inside handle without having to pull up on the little locking device
Iam an electrician and I even hate vehicle wiring😂😂
Was that glitter ain’t gold by whiskey Myers? I know for sure it was whiskey Myers
Wade Bowen fan huh??
Now It’s time for a steering wheel
The Smith and Weston knife’s are a lot better then that one
Nothing harder than working with in door parts. I would rather have my eyes scratched out. He he
Should have just called Zack to make it easier
You could have got one very easily at the junk yard off any F Series truck.
Very easily? It wasn’t fun getting it out of a decent door in my own shop, let alone trying to rip an old one out of a beat up truck in a junkyard. These notoriously fail, I wouldn’t want a used one
If Sergio can’t fix it your in trouble
Sorry I forget you put aluminum door handles last time,plastic handle 🤮
Truck looks like a dumpster. 😆
Damn you are treating this truck like shit. I use to really love your obs vids and even did similar things to mine but you have completely tainted that for me. Disrespectful to an amazing truck!
After watching this. Y'all need need Zack
Bye 😂
Found On Road Dead
Bye (Chris) lol
Where's your slim jim?